I think I'll always do maintenance on my own cars no matter how rich I get. No better feeling that fixing something that driving around town knowing you did it

@DayOffDIY

Жыл бұрын

its a great feeling!

Beautiful mustache Sir. So beautiful it made me cry a little. Thank you for sharing your mustache with our eyes.

@DayOffDIY

Жыл бұрын

Thank you Obie, my mustache says thank you :)

@qmann5714

23 күн бұрын

Lol!

My man! Loving this E46 service series :) You seem to be getting better with every single video, hope you keep it up :)

@DayOffDIY

Жыл бұрын

Michal! My man, thanks for the watch and support

Great video, clear and concise instructions plus a bit of humor. Thanks

@DayOffDIY

Жыл бұрын

Glad you appreciate it ! Thanks for the comment

Loving this e46 series ! Can never be enough e46 content..

@DayOffDIY

Жыл бұрын

Thanks Chad! Good to see you again

I love how you make car maintenance so simple

Thanks for the how to!! I just completed my first flush using a similar bleeder kit!!

@DayOffDIY

8 ай бұрын

awesome to hear that. thanks for the comment

Great incisive video on how to correctly bleed the brakes using a pressure device. Exactly what I needed to flush my BMW e39 540i. Subscribed!

@DayOffDIY

4 ай бұрын

Thanks Brian! Glad it was helpful!!!

I like the way you did this video, 1st one ive seen. Show n tell perfectly!

@DayOffDIY

8 ай бұрын

Thanks Hector! If you like this one, i think youll like some of my other content too!

Great video as usual but this one is super good. It’s a quick step by step guide to doing brakes yourself. Can not improve on this video you covered everything. I’m so glad you talked about the fluid level vs brake wear at 6:50 it really helps letting as many people as possible know this. 👍

@DayOffDIY

Жыл бұрын

Phantom! Thanks for the comment partner. Always a joy to hear your feedback

@DayOffDIY

7 ай бұрын

Phantom, Ive been looking for you in the comments for months! How are you?! you alive? check in or email me!

You did an excellent job on this video. Thanks!

@DayOffDIY

Жыл бұрын

Glad you liked it! Thanks for the comment

Great video. I use the same bleeding tool. Using this tool, I would recommend always bleed the clutch on a manual too. Works the same easy way. Cheers from Gemany, BMWs home country!

@DayOffDIY

Жыл бұрын

Great idea, should’ve hit the clutch while I had it up

@terrycarlin2443

5 ай бұрын

That is Correct , to lastly bleed Clutch being it runs off same master cyl.

way cool man. thank you. going to have mine changed today. I never knew it was necessary.

Wow man you made that job look so easy for a 1 man job, THANKS I love my BMW even more when I can do some of the work on it myself.

@DayOffDIY

Жыл бұрын

absolutely! the more you do on em the more you appreciate the process. progress not perfection

Thanks for the awesome video. Will be doing this soon.

@DayOffDIY

Жыл бұрын

glad it was helpful! thanks for the comment!

Very clearly explained. Thanks!

Like this video - straight to the point with good advice 👍

great video! Thanks for the info.

Really enjoy your content ! Straight to the point , informative and I can tell you pay attention to detail. Going to try this on my 528i E39.... would you mind telling me all the tools used for this brother? Do i need to buy the pumps? I am def looking forward to more videos and content with help my E39! lol

@DayOffDIY

Жыл бұрын

Just the Ystool Brake bleeder kit, and a wrench set to break loose the bleeder screws on each caliper. I believe this car was 9mm. usually its a 7,9,or 11 mm for bleeders on BMW

When I bought my 3-Series, not only that my brake fluid was as dark as yours, but the whole system was clogged with big white chunks of deposits. It was probably never changed in 20 years. It took a lot of effort to clean the master cylinder, abs pump, and the pistons in the calipers.

@DayOffDIY

Жыл бұрын

What a nightmare! It’s not hard to believe brake fluid went unnoticed that long, most people forget about it and never service it

@user-fx3fu1nc1r

7 ай бұрын

My e46 was similar. Looked like jizz

Very informative video - I'll keep this one open till I'm ready to change brake fluid! On the pressurized collection bottle problem - is there any reason that bottle should be pressurized? would it work better if you leave the cap of the collection bottle a little loose?

Thanks for the video! Just a thought, when you disconnect the silicone rubber connector at the brake bleeder nipple it causes a mess because the pressure in the collection bottle pushes the used brake fluid back up the collection hose. Instead, loosen the cap on the collection bottle after closing the brake bleeder to release the pressure without the danger of spewing brake fluid. Also with the loosened bottle cap the fluid in the drain hose will gravity drain back into the bottle when you pull the silicone connector off

@DayOffDIY

11 ай бұрын

good info! i used it again recently and i just took a lighter to a pick tool, and poked a hole in the top of the bottle to relieve pressure. i was tired of this thing spitting at me every time i disconnected it lol. great insight and thanks for the comment ! :)

@flxmkr

8 ай бұрын

@@DayOffDIYCan you add a demonstration of what you’re talking about to your video? I think I know what you’re talking about, but I’d rather see it in action so I know for sure. If I can get my husband to remove the tires, I think I can get the rest of this done. He thought I was nuts when I asked him “When was the last time we changed our brake fluid?” Like I was asking him, “When was the last time we changed the air in our tires?” It looks like our 2007 Dodge Caravan is due for a change in brake fluid. Mechanics (AAA) don’t typically do this when we ask them to change the oil, do they? Would we also have to change the power steering fluid? Thank you for this video!

@dodgysteve7699

5 ай бұрын

@@flxmkr I'm pretty sure that's American for "heat up a pointed tool with your lighter and melt a small hole in the top of the bottle" to relieve the pressure. A drilled hole would work also.

keep up the hard work 👍

@DayOffDIY

Жыл бұрын

Thanks, will do!

I'm second! I liked knowing the part about bottle level. Now I know why.

@DayOffDIY

Жыл бұрын

Good to see ya again partner! brought the work light around to each wheel for lighting with you in mind

@bogusienombre355

Жыл бұрын

@@DayOffDIY lit beautiful! Hate dark wheel well videos. Does nothing for the learning experience. Great job my man!

I have had the same fluid since 2008 - brakes work perfectly... I might change it for fun one day... but it gives me the impression, it's going to last another 10 years yet.

@DayOffDIY

Жыл бұрын

Probably so! Probably better for the rubber and hard brake lines to keep the water out of the fluid tho

WELL DONE BROTHER

Excellent work, 5 star ..thanks

@DayOffDIY

9 ай бұрын

Glad you enjoyed! Thanks for the comment

Great video. Thanks!

@DayOffDIY

9 ай бұрын

You're welcome!

I wish I could use one of those pressurized bottles, I have the old school square style one that you take off the metal lid, 1974 Oldsmobile Toronado

@DayOffDIY

Жыл бұрын

yeah thats a shame they dont adapt to the old style. You could use a fluid extractor with a piece of vacuum line on the bleeder nipple to expedite the bleeding procedure though! but thats just extra. gravity bleed would be a easy option

Couple of comments. First, I admire your tools! Second, You mention that brake fluid absorbs moisture. This is true and the propensity to absorb moisture increases as the DOT rating increases - Dot 2, 3 and 4. The reason moisture in the fluid is bad is because it will eventually corrode/rust the internals of the braking system. i.e., result in rusted and frozen calipers and/or slave cylinders, and even the master cylinder. Finally, when I bleed a brake system I compress the calipers and/or slave cylinders to remove as much old fluid as possible. Thanks for your posting.

@DayOffDIY

Жыл бұрын

Great information!!! Appreciate the feedback. You’re doin it right my friend!

Before anything, take a marker and mark the current fluid level. Then at the end, fill it ti that level so you know it’s not over full.

@DayOffDIY

9 ай бұрын

thats a great tip tyler!

Thanks, great info.

@DayOffDIY

9 ай бұрын

Glad it was helpful!

Great video

@DayOffDIY

11 ай бұрын

thanks marcus!

I would like to see you do clutch bleed. I have an e46 manual and need to get it done on my car. Would like to see your tricks.

@DayOffDIY

Жыл бұрын

Great idea! Should’ve added it into my brake flush video but I’ll do a separate one for clutch

Great video on a badly overlooked maintenance. If your hard up for cash and don't want to spring for this tool, Auto parts who have these will rent the pump to you and refund your money back once returned. Man, the times we live in. See how he has the towels where he works, brake fluid is an effective paint stripper. If yo do spill on paint, Soapy Wooder, sorry, soapy water, is best. I like to open bleed screws and push fluid out there when pushing pistons in, instead of back through the system so they get some new fluid in the system after declining a system flush, unless it has fresh fluid already of course. Older GMs were bad about the old fluid messing up the ABS unit valves. Remember the days when all we had was little test strips before the electronic moisture detectors, one end for brake fluid the other for coolant? I still have some, LOL.

@DayOffDIY

9 ай бұрын

Thanks weaver! All kinds of good information in your comment I used to use those test trips! Used to attach them to all of my old inspection sheets for the service writer. Gotta hit all the fluid with soapy wooder 🤣 Water will neutralize any spilt brake fluid. It can absolutely destroy paint if left alone Thanks for the comment friend!

Thanks for another informative video. I saw in your other recent videos that you jack up the E46 in the centre of the sill area to place jack stands both front and rear at the same time. Does the E46 have a jack pad in the centre as well? My two E36's only has jack pads front and rear. I got to get myself a bleeding tool like yours, my wife just runs when she hears me calling from the garage to come pump the brake pedal.

@DayOffDIY

Жыл бұрын

Glad you liked it! There’s no jack pad there, but the unibody is plenty strong to support the jack there in my opinion. Maybe I’ll do a quick video on some jacking tips for BMWs, because strictly relying on the jack spot locations is a pain. Yeah the bleeder tool makes it real easy, for brakes or clutch, turns it to a one person job :)

@MLC...

Жыл бұрын

@@DayOffDIY That would be nice, thanks. A lot of the BMW factory racers here in South Africa in the past have had jacking points welded into the centre of the sill area as well. Makes for quick pit stops

Thanks for the vid! Should I do the brake fluid flush before or after I change my pads and rotors?

@DayOffDIY

5 ай бұрын

i like to do it before so i don't spill any brake fluid on new pads and rotors, but either way is okay :)

I was here from the begging with another Harry Balls account(yt ban me lol) i said it then, glad i find it, this channel is awesome, you will get 100k in a no time for sure. Great editing skills in this one 😁

@DayOffDIY

Жыл бұрын

Harry! They took away your account?! Bummer! Thanks for stopping by

@DayOffDIY

Жыл бұрын

Appreciate the support, ain’t stopping til I hit 100k!

@Crotch_Goblin1

Жыл бұрын

@@DayOffDIY Yeah man, apparently some comment was against rules, but they didn't show me what comment and i couldn't appeal?! Crazy stuff man

@Crotch_Goblin1

Жыл бұрын

@@DayOffDIY You will hit it in no time, channel is amazing 😎

@DayOffDIY

Жыл бұрын

@@Crotch_Goblin1 lame, good to have you back ! Always enjoyed that username lol

One day can you make a video of your camera gear and how you set up everything in order to film? Also where can I get that type of hood camera stand that you used for the engine shots in the other videos?

@DayOffDIY

Жыл бұрын

Absolutely! I can run though that stuff. That might make a good video

Its funny how much auto maintenance knowledge my father shared with me from his decade+ of working on cars professionally (also from his lifelong hobby of working on cars and bikes). It has allowed me to do most if not all the work on any of the cars I've owned with great success. The money I've saved from troubleshooting my own vehicles and the time we've got to spend working on cars together has been irreplaceable. The one thing that truly baffles me is for years he was adamant that no matter what, brake fluid is not a consumable. So long as you do your brakes correctly and don't introduce air into the system, brake fluid doesn't go bad. He actually refused to help when I told him I was just going to bite the bullet on the next brake job and flush out the fluid for some fresh because "I was in for more trouble that it was worth". He's a great mechanic and knows how to work on anything so the brake fluid episode from nearly 20 years ago just baffles me...he changes the shit out on his motorcycles religiously so I don't know where the caveat with cars applies in his mind and he ain't telling, lol.

@DayOffDIY

2 ай бұрын

there is always more to learn! I will try to be a student til the day I die! the day we stop learning is the day we stop growing! Sounds like your dad shared some awesome knowledge with you. thats great !

knocking it out of the park bud. FYI, only england and old english territories drive on the left, all other european countries also drive on the right like we do. Hell, you have a lot of days off! I love it! That bmw is going to be better than new when you're done with it

@DayOffDIY

Жыл бұрын

Thanks partner, appreciate the info too! didnt know that bit about UK

@M3goon

Жыл бұрын

Only England? And old ‘English’ teritories 😂 did you forget Scotland, Wales, Northern Ireland…. For reference, countries and overseas territories that drive on the left and are right hand drive cars in Europe are: Akrotiri and Dhekelia Cyprus Guernsey Republic of Ireland Isle of Man Jersey Malta United Kingdom (England, Scotland, Wales & Northern Ireland)

@DayOffDIY

Жыл бұрын

@@M3goon dropping some knowledge!!! Thanks for clarifying Craig, appreciate the info

@Seba-wn3vl

Жыл бұрын

@@M3goon still it is a small amount compared to the left hand drive, he probably reffered England as a whole Britain, and 90% of people dont even recognize rest of the countries that you mentioned.

@fregyt

Жыл бұрын

Australia too left

Nice one.. Not just for the car ,,,motorbike well ..I was wondering why my motorbike's brakes failed when it got to hot..Thnx

@DayOffDIY

6 ай бұрын

this is true!!!

Great video, you look like my buddy named Pete he is a mechanic as well; same thick mustache

@DayOffDIY

Жыл бұрын

lol, thanks Jeezy!

When should you bleed the breaks, After or before changing calipers,drums,rotors? Or all? Does it damage the new caliper when bleeding the breaks after?

Can you do a video on checking/changing the fan clutch, as these are common failure points and most people don’t realise it’s reverse thread etc.....

@DayOffDIY

Жыл бұрын

I actually filmed it long ago but never edited it up, when i replaced the fan portion. Had a missing blade. Ill dig around for the clips. Good idea! I love suggestions, thanks bobby

Very clear and concise lesson. Thanks.

Did you ever take a moisture sample from the caliper bleed port after letting some fluid out then take the sample? If so what was the moisture content then? Does moisture that gets absorbed by the fluid at its weak point, the cap area, then transfer down thru the lines like a worm? Or do you think that the moisturized fluid stays up mostly in the reservoir area?

@DayOffDIY

8 ай бұрын

thats a great question! I havent tested at the bleed port yet but i will my next flush. I think moisture works its way in through the cap at the master cylinder, and maybe through the rubber hoses... not sure how it gets in there

Greetings from Canada

@DayOffDIY

Жыл бұрын

Hello there! Thanks for stoppin by

Do you need to pump the air frequently or is once enough? Cheers

Good info

@DayOffDIY

8 ай бұрын

thanks neal!

Afte watching few minutes I noticed the thumbnail. I'm still here, but I have to ask, thank you for not sucking on the bleeder calves.

My Acura recently went for a 20k mile service and was told it needed a brake flush. I was surprised as this is the 4th Acura MDX I’ve had and never been recommended this before even though each vehicle has reached 35+K in three years. The way I use the car and location has not changed. I question where it needs changing yet? Any advice or thoughts?

@DayOffDIY

8 ай бұрын

Hey adrian! that comes down to the service advisor. A good one should recommend a brake flush at a reasonable interval. Thats why i test all the vehicles i recommend it on, so i have proof that its due. BMW actually recommends the service via the dash indicator every two years

@adrianpgoode

8 ай бұрын

Thanks for your input and comments. I did just take a small sample from the master cylinder and if not mentioned by the service advisor the color would not alert me to a flush being needed.

@DayOffDIY

8 ай бұрын

Sometimes the color can be okay but it’ll contain moisture as well. All depends on how it tests. If you’re curious you could always buy some water testing strips or a pen in the description 👍🏻

I have one of those bottles but the cap that goes onto the reservoir wouldn't seal and I got fluid seep out and food the area.

@DayOffDIY

Жыл бұрын

What a bummer! You inspect the deal or contact the manufacturer?

How much old dirty brake fluid was left in your ABS modulator? On ABS cars they tell us to exercise those channels/valves with a bidirectional scan tool to flush those out too without introducing air bubbles in there. Overall the system should be fairly well sealed and should not let water in, almost as hermetically as AC refrigerant circuit?

@DayOffDIY

9 ай бұрын

Ya know, I did brake flushes for 6 years and never went through the bleed function on the ABS. Never had any issues with it

Dude! Your ‘stash game is so good, it looks fake 🎉🎉🎉🎉

@DayOffDIY

7 ай бұрын

Hahahah thanks tomas!

Also wear safety googles. They look goofy and ugly but if that fluid gets in your eyes you may find yourself in the emergency room. Also watch when you take that hose off so the spray doesn't go everywhere. Brake fluid is bad for your paint. I am not sure how bad DOT 4 is vs DOT 3 but I know either one is poisonous and corrosive. It is not corrosive as in "I'm melting" but it is not good for you or your paint! I have no idea how bad modern brake fluids are on paint but I do know don't get it on there and if you do, get a wet sponge or rag and wipe it up quick. Also treat it like coolant and don't let your pets lick any of it if it spills. I like to let my cats roam outside but I am cautious when I do my brakes not to let them near and to watch them more closely if they get near so they don't lick any. It has a bittering agent but I would not trust it to stop them from consuming a harmful dose since it does not take a lot.

@DayOffDIY

10 ай бұрын

thanks for the heads up! ive been wearing safety glasses a lot more often now, and I always rinse down any spilled brake fluid to neutralize it afterwards. I also drilled a hole in that brake fluid bottle to relieve the pressure so it doesnt spray anymore.

Thanks

@DayOffDIY

Жыл бұрын

Thanks for the comment Lineman!

Good story line

@DayOffDIY

5 ай бұрын

thank you! much appreciated!

Cheers! Question: Will this flush the ABS pump as well? Meaning no need to run the pump manually through the procedure with the diagnostic tool?

@DayOffDIY

Жыл бұрын

With the pressure from the bottle I can only assume it flushes a majority or at least a portion of it. I think the bleed procedure would get the rest of it through, however with the volume of fluid after a flush, if it doesn’t get all of it it would dilute it with enough fresh fluid to call it good in my opinion. The bottle with 30 psi should be enough to push the fluid through the ABS. I think.

@DaPhobos

Жыл бұрын

I would agree. Thanks a lot, great content!

@DayOffDIY

Жыл бұрын

@@DaPhobos thank you!

Hi. so i noticed my brake pedal a bit stiff after i refilled my brake fluids but did not bleed the brakes. Would this be the main cause of a stiff brake pedal? thanks

@DayOffDIY

Жыл бұрын

it could be multiple things, you could have a compromised vacuum line going to the brake booster, which is attached to your master cylinder. A test for this is to pump the brake pedal with the engine off til its hard, then start the car and feel for the brake pedal to depress. not bleeding the brakes usually leads to a soft squishy pedal

@cloudchaser9951

Жыл бұрын

@@DayOffDIY Thanks i just tested the brake booster. it is working fine. hmmmmmm

I never suck fluid out of the master cyl. I just use a 1 man bleed kit and trust me, that master cyl will go low plenty fast. Pump and fill, pump and fill. Works like a charm.

@DayOffDIY

4 ай бұрын

thats a good way to do it as well!

Brake Fluid: you can depend it leaking out when you service it. MUST HAVE ON HAND: Blue shop towels, old torn tshirts, ETC. You cant skip the dry air test. You can figure out what adapter o-ring works best. Pressure up to 12psi. 15 psi is gonna bust the typical 7 year old car seals.

I have heard from someone recently who had their car at the dealer for service. Service manager recommended fluid flush and the owner said he had never heard of this in 40 years of owning vehicles. I think with leases you probably never get to the point where the fluid is compromised enough initially. When that ABS module goes out you will wish you had the fluid flushed. They are not cheap to replace since most need proprietary (dealer) software to function for specific vehicles.

@DayOffDIY

9 ай бұрын

In my experience I’ve always heard of brake fluid flushes since my time in auto academy in high school. It’s often overlooked but the moisture content results speak for themselves

@user-tb7rn1il3q

8 ай бұрын

It’s a lot cheaper to put tape over the ABS light. I hate ABS, traction control, stability control, etc. They actually make it dangerous to drive.

@user-fx3fu1nc1r

7 ай бұрын

I just don't know. Automotive education is all over the place. Uneducated service departments lead customers to believe they are serving their vehicles as it should be when in reality they are getting oil changes and no major work. Or customers not listening to correct service advice and poorly maintaining a vehicle

@plugpenguin1660

7 ай бұрын

You just need free inpa software on any windows laptop

@user-fx3fu1nc1r

7 ай бұрын

@@user-tb7rn1il3q I opened the speedometer and removed the bulb and dingger

Straight out Valvoline DOT4 was already at 2% what's your experience with fresh fluid?

@DayOffDIY

Жыл бұрын

To be honest with you I’ve never really tested it right out of the bottle, but I want to now!

Dropped a like👍 Most of Europe have LHD cars and drive on the right btw

@DayOffDIY

Жыл бұрын

Thank you! And thanks for the info :)

Thanks!

@DayOffDIY

5 ай бұрын

Bobby youre thee man! thanks for the support!

I’ve been starting to work on my car myself, is this concept the same for most cars? Sorry if that question is dumb lol I have a 2015 camaro and I’ve had it for about 3 years but I have not yet had a brake service done especially from Chevy dealers cause it’s expensive lol but I do wanna try myself, just a tad nervous I’ll screw it up.

@DayOffDIY

Жыл бұрын

There are no dumb questions my friend! This concept is pretty much the same for all cars. the only thing that changes is the threads on the brake fluid reservoir as well as the brake bleeder screw sizes. If you have a kit like i listed in the description you should be able to flush brake fluid on really any make an model

@icegodskittles

Жыл бұрын

@@DayOffDIY I appreciate it ! Thank you man, I’m gonna try when I look up a couple more vids. Wanna make sure I know what I’m doing going into it! Great content btw super helpful (:

@eligreg99

Жыл бұрын

Dude I literally went in for a recall and they recommended a brake fluid change for $293 on a Chevy Malibu 2013 lol. The dealerships are crazy

@icegodskittles

Жыл бұрын

@@eligreg99 that’s my point they’re so overpriced lol plus they always “find something else” that you didn’t even go in for

3:29... For all of you who say you will never use the 9 mm in a wrench/socket set...lol That's not the only place... you'll need a 9 mm on some cars to hold the piston in place on a McPherson strut.. that's also a 9 mm...☝️

@DayOffDIY

Жыл бұрын

Hahahah rare but still used! Thanks for stopping by

Excellent video!!! A brill tool to service the braking system!!! But please remember that brake fluid is a very toxic liquid!!!! Will take the paint off your car before you can say shit!!!! Regards Ian 👨‍🎤🇳🇿👍

@DayOffDIY

8 ай бұрын

Absolutely, brake fluid will destroy your paint. Thanks for the comment Ian!

Could we get one for the coolant system? :)

@DayOffDIY

Жыл бұрын

Absolutely! Great idea, just added it to the list

@namvu4180

Жыл бұрын

@@DayOffDIY woooo

a tip for you though drill a small hole at least 2mm on the cap of that catch bottle so You dont pressurize it when using the pressure bleeder so You avoid 3:46

@DayOffDIY

5 ай бұрын

Great tip. I did it after I shot this video, heated up a pick tool and made a little hole for pressure

mandatory wrench drop.. sometimes multiple drops are required

@DayOffDIY

Жыл бұрын

Always, you never know how many itll take to get the job done lol

@AllanAdamson

Жыл бұрын

@@DayOffDIY for sure, maybe one day I get through a job where I don't drop something haha

informative personal~

I put power steering fluid in my brake fluid what should I do lol

@DayOffDIY

5 ай бұрын

did you really?

I never use a fluid tester cuz there is one overlooked flaw: water sinks in brake fluid. So way before the tester will even indicate the presence of moisture in the master cylinder, water present in the system will have already sunk to the lowest point, which is at the calipers. I as a rule change out the fluid on a time basis regardless of what the tester shows me.

will this procedure work for hybrid car?

@DayOffDIY

11 ай бұрын

i dont see why not!

I have a question, is there any way you can link those tools in the comments and @ me? I want to purchase them for use

@DayOffDIY

6 ай бұрын

Hey Elvis, all of the product links are in the description of the video 👍🏻

dont need to use the diagnostics to bleed ABS/DSC module?

@DayOffDIY

9 ай бұрын

nope! never had to for this type of flush. youre technically not introducing air into the module, unless you were to suck the brake reservoir dry and then add fluid then bleed.

30 psi?! That's about TWICE the recommendation. Whomever is reading this, do NOT push 30psi through your brake lines.

@DayOffDIY

4 ай бұрын

good to know, i usually do 15-20

@FckYourFeelingsYT

2 ай бұрын

@@DayOffDIYnot 30 psi? It’s what you said.

@Matt-bg6kf

2 ай бұрын

I 35 psi during stop and go traffic

@ChooseMyNam

2 ай бұрын

​@Chrisp_az Yes he did. 2:36

I find that compressing the calipers while the bleeder is open and removing the fluid from thr caliper cylinders is a good idea. That fluid needs to be replaced and will not if you don't compress the calipers.

Firestone wants to charge me $170 so i decided to search what is this about. Wonder if they do all that tho bleed all four wheels. I should asked them whats included

I'd recommend using a clear tube

@DayOffDIY

5 ай бұрын

for the brake fluid catch bottle?

When you change the brake pads, shouldnt you be competent enough to keep an eye on the brake fluid reservoir, and drain as necessary?

@DayOffDIY

6 ай бұрын

not everyomne is that knowledgable

How accurate are those amazon pens really?

@DayOffDIY

Жыл бұрын

theyve been surprisingly accurate for me over the years. worth the small price in my opinion

What if one never change the brake fluid for the last 10 years, and there are seem to be No brake failures, given that there are No leaks in the brake system?

@saomychau7010

6 ай бұрын

I think your answer is at (8:00)

@DayOffDIY

5 ай бұрын

well said!

I believe there is a step to pump the brake 3 times and hold down to get all the fluid bleeded out.

@DayOffDIY

10 ай бұрын

thats how it would be done without a pressurized bottle. if you didnt have this tool and had a friend to help you, thats how you could get it done

@DayOffDIY

10 ай бұрын

with this tool its a one person operation

@John-tc7yp

10 ай бұрын

@@DayOffDIY thanks!

my brakes are soft---is that becuse I have ignored this DRAIN /FLUSH BRAKE FLUID notification?

@DayOffDIY

Жыл бұрын

Could be a few things Lisa, but lack of maintanence of brake fluid usually wont make a pedal go soft. its possible it could be an issue with the brake booster, or even a leak somewhere. Id get it inspected

@MsFirstserve

Жыл бұрын

@@DayOffDIY Thank you.

are you not supposed to pump the brakes when draining?

Does this affect the clutch pedal also?

@DayOffDIY

9 ай бұрын

nope! never had it affect the clutch pedal

@gameova5962

9 ай бұрын

@DayOffDIY ah crap. My gear changes are not as smooth and I thought it may be due to brake pad wear. The clutch peddle feels like only 75% effective. Any ideas? I think it your country its the same gearbox as the 1.4t chevy cruze

@DayOffDIY

9 ай бұрын

its possible the clutch plate could be wearing down

If it doesn’t exactly change drivability of the car, why do it?

@DayOffDIY

Ай бұрын

Prevents rust and early failure of brake calipers and brake lines n hoses. Will affect brake feel eventually if not done

I won't change and flush the brake fluid if the paddle does not feel spongy. I only replace the brake fluid in the reservor with DOT 4, NOT DOT 3.

@DayOffDIY

9 ай бұрын

Brake fluid should be replaced every few years imo

most of europe is actually LHD, only the brits are RHD. so its mostly the same for all of the procedure.

Thought he was talking to me because my names Alec. I was shook

@DayOffDIY

7 ай бұрын

Lolol hello my fellow Alec! Thanks for the comment

That catch bottle should be vented properly so it isn't being pressurized.

@DayOffDIY

9 ай бұрын

You’re right, I’ve drilled a hole in it since then to relieve pressure

He didn't test the new fluid to show the device is good or bad...overall, great video!!

How much brake fluid should i buy for a Tucson GLS flush?

What you said is right, but the tester may be a trash. Dip it into new brake fluid it would be the same

@DayOffDIY

8 ай бұрын

This is true! I’ll have to test it and double check it, however, I have been testing other cars and the results vary

What about abs?

@DayOffDIY

Жыл бұрын

you can bleed the ABS through a scan tool during the process, but i never do any pay attention to it

There are reviews on Amazon stating that this tool reads even new brake fluid as bad.

@DayOffDIY

6 ай бұрын

Ive tested it against both and mine is testing accurately. I assume they can be hit or miss

Bow chicka bow wow brake flush

@DayOffDIY

8 ай бұрын

were bringing brake flush back