Awesome work man! I'll try to replicate your design as well at some point. My parents need a third helping hand in the garage. This might just do the job!
@HaWiWe
Жыл бұрын
Hey, I'd love someone to also make one. All the designs/dxfs were posted on the V1Engineering forums, nearly everything I make has been shared there for free. Feel free to pop in and get them. 🙂
@zubalea2 жыл бұрын
Your MPCNC looks to be working flawlessly. Did you do any updates to it since you first built it? Anything you would do differently?
@HaWiWe
2 жыл бұрын
I experimented with the drag chain, I had another solution before I didn't like, but this one is great. I also should have made the cables longer, it's a little tight in some places, so I can't add a dragchain at the side and back which I would like to have. Also I would (if I had the time) build a LowRider 3 and a smaller Primo, there is a lot of swinging in the pipes when milling in the middle of the workspace (it does not alter the results, but it sounds scary). I should also add that I am not using a Rambo board but a German one together with the TB6600 stepper drivers that have a lot more power than the small ones on the Rambo. More details can be found in my build thread here: forum.v1engineering.com/t/mpcnc-primo-schneewittchen-oldenburg-germany/20022.
@zubalea
2 жыл бұрын
@@HaWiWe That is good information. I am going to study that further before buying the parts. Thank you for your response. By the way that link points to a aerial photo of a village.
@HaWiWe
2 жыл бұрын
@@zubalea Ah, thanks for catching that (though it's not a village but a town!! :D). Copied the wrong tab... Fixed it for you. :)
@HaWiWe
Жыл бұрын
I added a dust collection which is really great, see here: www.printables.com/model/244558-dust-collector-for-mpcnc-primo-with-makita-router
Пікірлер: 7
Awesome work man! I'll try to replicate your design as well at some point. My parents need a third helping hand in the garage. This might just do the job!
@HaWiWe
Жыл бұрын
Hey, I'd love someone to also make one. All the designs/dxfs were posted on the V1Engineering forums, nearly everything I make has been shared there for free. Feel free to pop in and get them. 🙂
Your MPCNC looks to be working flawlessly. Did you do any updates to it since you first built it? Anything you would do differently?
@HaWiWe
2 жыл бұрын
I experimented with the drag chain, I had another solution before I didn't like, but this one is great. I also should have made the cables longer, it's a little tight in some places, so I can't add a dragchain at the side and back which I would like to have. Also I would (if I had the time) build a LowRider 3 and a smaller Primo, there is a lot of swinging in the pipes when milling in the middle of the workspace (it does not alter the results, but it sounds scary). I should also add that I am not using a Rambo board but a German one together with the TB6600 stepper drivers that have a lot more power than the small ones on the Rambo. More details can be found in my build thread here: forum.v1engineering.com/t/mpcnc-primo-schneewittchen-oldenburg-germany/20022.
@zubalea
2 жыл бұрын
@@HaWiWe That is good information. I am going to study that further before buying the parts. Thank you for your response. By the way that link points to a aerial photo of a village.
@HaWiWe
2 жыл бұрын
@@zubalea Ah, thanks for catching that (though it's not a village but a town!! :D). Copied the wrong tab... Fixed it for you. :)
@HaWiWe
Жыл бұрын
I added a dust collection which is really great, see here: www.printables.com/model/244558-dust-collector-for-mpcnc-primo-with-makita-router