boiler low watercut off issues
Тәжірибелік нұсқаулар және стиль
boiler low watercut off issues
www.valuetesters.com
merch = teespring.com/stores/steve-lav
/ stevenlavimoniere
lavimoniere productions llc
subscribe to my channel
/ @stevenlavimoniere
lavimoniereplumbingandheating....
Пікірлер: 38
"I had one in the truck." We knew that.
Always good to carry a spare LWCO probe for those Hydostats I've come across that issue myself. I like the Honeywell Aquastat myself. Good video as always.
The metal clip on the temp probe sometimes needs to be bent slightly so that it makes good contact with the inside of the immersion well on those Hydrostat controls. That’s the only issue I’ve seen with them. Haven’t had to replace a temp probe yet, but good to know they are available as a service part.
Nice setup. New tanks and that burner looks good. Recirc pumps look good too. Miss Molly, well she looks good but that's because you got her spoiled. lol Take care of her Steve, you and her are sort of connected at the hips .
Steve, I learned something about those probes!
Seemed like too new a unit to be having troubles. Sometimes having more sensors isn’t a good thing. Just makes for more problems down the road. Miss molly looks pampered for sure
Thabks to your video, I learned about the probe for the lwco. Like you said...I knew I had water as it was at 20psi. I turned off power at the service switch, push the probe wire in more (must have gotten loose) and disconnected then reconnecred it on the hydrostat. Turn the service switch back on and had to reprime after due to waiting for an oil delivery and putting in 10 gallons of diesel to tide us over. Up and running now. Didn't have a probe in my truck so figured I would just make sure the current probe was in the way it should be first. Maybe a good first step if you don't have a probe and doing it solo. However, if you're already paying for a repair it's nice to know that you replace it as a precaution seeing that you're already charging. Have any videos on replacing a slightly leaking hot water coil gasket?
I live in VA same for us. Rain Mon Tue, Wed switch to snow
Steve you forgot to change out the sump pump unless you're trying to make that into another video. I'll see what video you put out tomorrow. Molly's new sweater looks great. Peace brother and Molly
Nice clean system to work on. Looks like you had same crappy weather I had in Ohio. I was re watching one of your vids from 3 years ago again when notification popped up for this one.Thanks for the video Steven!
@picklerix6162
4 жыл бұрын
That boiler looks new.
Parents had an issue with the low water cutoff a few years back after my Dad did the annual service on it. He couldn't figure out why it wouldn't fire up (last year doing it himself, mind is too far gone from Parkinson's now). Must have had air in just the wrong spot. Bypassed the cutoff just long enough for it to fire and let the circulator run, heard the air at the high vent, then shut it off and reconnected the cutoff. Been running fine since. It's an older cutoff though, just interrupts power if it doesn't detect water in the pipe. Just move a wire over to bypass it.
@cappachino007
2 жыл бұрын
Trying to troubleshoot on a laars pennant. Goes into auto high limit. The low water cutoff keeps blinking
Miss Molly looking sharp
Just finished watching
You know your stuff!!!!
great info. thnx. if the probe type LWCO is defective, what other device is there to SHUT DOWN the boiler, in a low water situation? I am scared, to think that there is no OTHER safety DEVICE on a steam boiler, if the probe type LWCO, FAILS. Please comment. Anyone else also can give an input.
Mine is stuck in the well. Any idea how to get it out without ripping it apart. Btw, burner has been off for about 24 hours. Not sure if that’s the reason it’s jammed (expansion/contraction)
do you happen to know where i can order that probe sensor or have a part number. have same issue with mines but cant find a it on their website or do i just go with what shows up online for hydrostat.
Above my pay grade? Really!
New Peerless and tanks that won't a cheap job. I had a customer who actually put in a 10 gage 500. That thing will still be there when all of us are gone.
@kenenos6520
4 жыл бұрын
Kyle Bass huh?
Another sweet video, thanks! After you perform a combustion test, what do you use to “plug” the holes in the exhaust pipes?
Where would someone buy that probe?
Cool 😎 Peace ✌️
Steve-after all these years of service calls, it seems Becket has the monopoly on boilers. any experience on better units?
@erikj.2066
4 жыл бұрын
Beckett makes the burners, not the boiler (this boiler was a Peerless). The other common burner manufacturers are Carlin, Riello, and Wayne. Everyone has their favorite flavor, and some makes/models are better for certain applications than others.
Where do we go for more interactive talk?
Hello, im from Rhode Island and i have the same boiler with the same system, what would be a proper temperature setting for heating?, my is also oil. I feels like my boiler is not heating well
@Jordan-yx5gb
11 ай бұрын
Low 160 High 190 I’m from RI also
Houston we have ignition! Itchy wabbit lol
Ms Molly looks a lil hot there. better turn down the gundy there in the cabin!
I believe the boiler water completes a circuit to the probe by acting as a ground. When the water becomes low, The ground is broken thus the circuit is open. Not a 100% on that.
system is to new to be having issues like that
@Wolfhound.
4 жыл бұрын
@@v-modsolutions6946 ahh well would that of been his fault or something factory not installed right
Reminds me of buggs bunny
Dang, I'm first today. Good golly Miss Molly.
First comment