The only good video on plastic welding on KZread. Good bond, good technique And a nice finish.

welder by trade and this is the only video i have come across that shows how to properly spin the filler material to achieve a solid bond- way better than just mashing it in! thank you sir-

Excellent tutorial. This man knows what he's talking about! Great job, thank you!

If he’s still with the company, give this man a raise

was hoping to hear him sing "silver and gold" at the end

I agree with the others, this is the best plastic boat welding video I've seen.

You tutorial is helping me bringing clasic kayaks and new kaykas all across Earth, thank you Very Much!!!

FYI: This is the ONLY GOOD video on boat welding I have seen on KZread!

@doorcountykayaktours9387

9 жыл бұрын

Nice! Boat welding is tough work to do.

@samatsamat1416

7 жыл бұрын

Top Kayaker

@ImMora1

4 жыл бұрын

Yeah most others just melt the material they are adding and smear it to the crack. That is not welding.

That's the best plastic welding job I've ever seen done

Beautiful!! Thank you for sharing your tech! I will be doing a test pnl and atempting your twirling trick to mix the plastic soon. Thank You!

Finally, a real plastic welding video, not a soldering one. Welder by trade here too. As soon as I saw the swirling I grinned from ear to ear. As it weird that I'm actually looking forward to scratching my new kayak now?

I'm a welder by trade I've never welded plastic but this looks like a good way of doing it to me , Nice job and nice clip

Thank you for an excellent tutorial.

Lots of cheap stuff is made out of HDPE, which is what you need to weld your kayak. There is a triangle molded into the plastic item, usually on the bottom, with a 2 in it if it is HDPE. Gas cans, flower watering cans, and loads of other cheap things are made out of this stuff. All of it will melt into and fill a crack in an HDPE kayak. You can buy welding rods, but you don't have to have one if you have an old plastic gas can lying around.

Excellent! Thank you.

This is the best crack repair on a HDPE kayak in KZread

thanks nice video very helpful and I seen those welding rods on ebay

Nice work!

Thanks a lot!

Excellent!

thx Dude..... thats Welding in plastic top nice

fantastic. I've got a 2013 Stomper 90 with a long gouge in it, 2mm wide, 0.5mm deep right under the cockpit. I was wondering weather I should infill that like you would on a second pass of your weld. or just leave it. I have the heatgun, I need to get a step down nozle and rods so no rush.

Thanks guys it is a good demo on how to weld, If using a donor boat for welding rods is the size of the rod important, also would you say this produces a boat as good as new or is there always a weak spot?

thank you for sharing

Brilliant ThankYou

Had poly craft nearly 20 years never had problem with itfished rough conditions narooma too evens head crossing bars bad seas all conditions still have it love it fished everything from shallows too 40kms offshore if you guys break boats not know how

Excellent.

Do you think this will work on a Malibu extreme kayak the hulls are thinner

if the plastic is not too thin, try sanding off the high points, then use wax to fill the low areas and buff it out. this does 2 things, it fills in the scratches, and adds a smoother finish which slips through the water nicer.

Great tut and info...A lot like brazing metal just way cooler and with hot air instead of flame..My guess practice makes perfect...Gona get me a bucket fresh clean and not brittle...Cut out a couple stirps for welding rod...then make a few deep scratch and holes in bucket...then Practice the above instructions on bucket instead of KAYAK tell i feel confident.....Be sure Bucket is HPDE 2...

شكرا لك على هذة المعلومات القيمة 4CRS الان أصبح العالم قرية صغيرة ولابد وأن يكون هناك أمانة وصدق فى التعامل مع الاخرين وكل إنسان يقدم لهذا العالم ما يقدر عليه من أالجنس البشرى شكرا جزيلا لفريق العمل إسماعيل عامر مصر

Will this work on an old green Colman canoe? From the 80's

Obie wan canoe be:)

Can this method be used to repair Christmas blow molds that are made of HDPE plastics?

Is that a Milwaukee heat gun with an adapter tip?

I want to weld plastic pods on to a plastic boat would this work

Super

you dont drill a hole to keep the crack from spreading ?

@dp4auburn

6 жыл бұрын

nileor1 that would be true but the crack would go all the way through for you to need to drill it. This equates to a deep surface scratch realy

Thank you for the video. Quick question. I have a small dinghy plastic boat that developed a hole. Does the boat have to be made from HDPE in order to do plastic welding? If yes, how can I tell whether it's HDPE or not?

@nate4036

3 жыл бұрын

I’m almost positive that all plastic water crafts are HDPE. If you need a piece of material for the weld or patch. Just look for the triangle or square with number 2 in it. Hardware store buckets, even some detergent containers will be correct materials

@perfidiousalbion9975

8 ай бұрын

Some are LDPE

where i can buy the welding rod?

@rondeti4532

7 жыл бұрын

what is the rods called and where can i buy please thanks

@wesleynelson1776

4 жыл бұрын

You can make Rods by cutting strips of any HDPE2 plastic. The emblem will be on most plastic products like five gallon buckets milk crates and such

how do u find out what type of plastic the boat is made of?

@jimmywaynejohnson2735

7 жыл бұрын

contact the manufacturer to make sure, but nearly all kayaks are HDPE like the one in this video.

It's called a V butt weld👍

Everyone asking where to get the rod, most of these boats are made of the same plastic as milk jugs....

what?

remove scratches from dragging on mud or sand? You don NOT remove said scratches.. you ignore them ;D

You can light an empty oil bottle on fire and let it drip onto the crack

Plastic boats crack dude... If you're hitting enough rocks to crack a boat in 6 weeks of use you should already know this though...