another great video explaining👌👌👌

Hi I know you already do a nice job . On the app. I have something that I would love to add. I would ask if you could add favorites in the edit parameters list . It would be much easier to adjust the motor rpm . And other things .

@TheCarpPilot

Жыл бұрын

That's a good idea. It is actually on my todo list, just not had the time for it (and sadly will not have time either in the near future). But for sure, a screen with the most useful parameters to set will be time saving indeed!

Great presentation. You stated in the video that you purchased the main wiring loom ready made. Do you have a link so I can purchase ? Many thanks. Am looking forward to the rest of the build.

@TheCarpPilot

Жыл бұрын

It came ready made from Dennis as well. Reach out and ask him.

@stuartgriffiths4299

Жыл бұрын

@@TheCarpPilot Will do. Thanks.👍👍

Nice job👍 where i can buy bait thrower? You make alone?

@TheCarpPilot

Жыл бұрын

It is an original bait thrower from DHconcepts that fits their boats like a glove. I have however custom fitted a new holder (a lot of measuring and 3D printing involved) as I wanted to reduce weight even more with a light weight brushless motor. Hence my use of a brushless WSC and the 3-wire aviation plug. The standard version is a brushed type, using a 2-wire DC plug. And to be honest this is also much easier to install.

@patrickweij7028

9 ай бұрын

Hi, im realy glad with youre video's! So good explayned😁 May i ask you what motor you used on the baitthrower and what esc please? Thanks in avance 😁

Where did you purchase the prefabricated cabling system? How can I find it to buy?

@TheCarpPilot

4 ай бұрын

I bought it together with the hull as a kit. It came tith all the right lengths and connectors to fit the boat. Not easy to build something like that for any boat...

How did you shorten the RM 5Pro cable?

@TheCarpPilot

3 ай бұрын

Two options, tried both. No favorite: 1. By cutting out a middle section and keeping the connector: Here you should practice using the cut-off middle section before soldering your result. You must make sure to carefully peel back metal film and plastic film on each end. Then remove protection and solder one wire at a time. And finally reapply the metal and plastic wrapping. I also added a shrink tube with glue outside to protect from moisture. By reapplying all protection in the same order you should keep the shielding and avoid to get a spot in the cable vulnerable for EMI from other electronics in the boat. 2. Here you need some guide. Colors and pins are described in a picture on the facebook Carp Pilot Pro user group. What you do is to desolder the socket from the main board. Then you cut the cable to the desired lenght (allow some extra length so you can correct a mistake by starting over). Remove protection for 4-5 cm of the outer cable, then remove isolation of 0.5 cm and then solder the wires into their respective holes where the socket once was placed. Here you must take great care not to break the red and black wire for the transducer as these are very thin and brittle.

good morning, I am writing through a translator. please write me where I can buy the raymarine dragonfly set that you show in the video. I have already found the signal amplifier. I don't know where to buy the rest. Thank you for your answer.

@TheCarpPilot

11 ай бұрын

Well. Shops dealing with boat equipment would be the first to try. Living here in Norway, around 95 % of the components needed for a baitboat must be purchased abroad. But Raymarine I can get here locally. There is a rumor this mode is about to be cancelled. So if you want one then do not wait too long Did a quick search and found new and used also on eBay. As for online shops abroad I do not have a list for Raymarine.

@mariuszlis304

11 ай бұрын

Can you send me a link where I can buy.

where can I find such a thrower?

Do you have a link for the mavbridge UDB please

@TheCarpPilot

Жыл бұрын

I used this (the "color" option 1.0 for pix) 2.4G Wireless Wifi Radio Telemetry Module With Antenna for New MAVLink2 Pixhawk APM Flight Controller FPV Drone Smartphone Table a.aliexpress.com/_mNbGxja

Hi. What motor did you use for the bait thrower?

@TheCarpPilot

7 ай бұрын

It is a spitz motor (brushless). The specs are visible in the table in the first video (around 1 minute in). Spitz C3242-06 (5mm shank, 1000 pwm, 50 A). For this small bait thrower the motor is totally overkill (it is small but very powerful). I tuned it down to reach max 1650 PWM. And when running it from the app (servo button) I set it to "momentary" with only 1 sec running time. The basket is empty before that second has passed.

@CosminFrinculescu

7 ай бұрын

@@TheCarpPilot Here, we have some modules for the bait thrower motors, to start slow and then rev, not full power from the start. I liked your motor because of it's dimmensions, I think I will try to find one similar. Thanks for the info.

Where did you buy the shank ?

@TheCarpPilot

Жыл бұрын

The shank is a premium propeller shank solution that comes pre-greased and is also with ball bearings, made in Germany by the DHconcepts company deigned for and use with all of their boats.

@JDeBoer-un9wt

Жыл бұрын

@@TheCarpPilot awesome i will check if i can buy them seperate