BMW E60 2006год. DISA упала на 232000 км. Симптомы: неполная тяга, вялость двигателя и ......(!) вибрации при нажатии на педаль газа на любой скорости. Автору СПАСИБО за четкое и нужное видео! Я делаю многое на машине тоже сам! Не знаю, поймёте ли русский язык, но Гугл переведет! Всем, кто читает и любит исправную BMW, удачи и любви! Я из РОССИИ!

Great stuff. Replaced the starter. While the car was apart I picked up a large DISA valve to install.

Splendid video, George!

That was cracking George; I was just checking mine and got stuck at the throttle body, so checked KZread - as always. Your video was clear, and easy to follow - Thanks a million - I've subscribed ;-)

@GeorgeAusters

3 жыл бұрын

Glad to help man!

You are a master!! tnx excellent video, audio, explanations, shots just perfect

George, you made it look so easy mate, good job.

@GeorgeAusters

4 жыл бұрын

Haha wait til you see the other DISA valve replacement👍🏻

A disa valve that does not close fully or open fully will affect the power, torque and responsiveness of the engine in a big way.

Hi George, very good tip about fix parts, didn't know them and checked their site now, they have interesting prices. 👍

@GeorgeAusters

4 жыл бұрын

Yep I only just came across them myself, very good prices👍🏻

Very good video Pal !!

@GeorgeAusters

2 жыл бұрын

Cheers👌🏼

Great video thanks for taking the time to make it, clear instructions. Gave me hope ill do it myself vs dealer just order OEM parts. Thanks again 07 530Xi owner

@GeorgeAusters

2 жыл бұрын

You're welcome!

Very good walk through video.

@GeorgeAusters

Жыл бұрын

Thanks Matt!

Very good tutorial

@GeorgeAusters

4 жыл бұрын

Cheers mate!

Hi mate, The normal DISA valve opens and shuts, right? The one you took out stays “open?”

Good job!

@GeorgeAusters

4 жыл бұрын

Thanks!

Super job

@GeorgeAusters

4 жыл бұрын

Thanks

cheers George

@GeorgeAusters

4 жыл бұрын

No problem Colin!

Just realised the rattle I’ve had since cleaning my intake is this! Shame fix parts online delivery is quite a while so what I did was order the febi one that takes 22 days for delivery and also ordered a Chinese copy off Amazon for £46 as at least it’s safe and not risking the pin or plastic going in my engine! Thanks George maybe saved my engine there mate 🙏👍

@GeorgeAusters

2 жыл бұрын

Good stuff, are you replacing both or just one?

@thedetailingdoctor5746

2 жыл бұрын

@@GeorgeAusters just the big one for now small one seems to be working fine but it will be on the list. The gearbox mount and guibo centre bearing and steering arms are first in line

Great info any chance of doing video of bmw engines fitted to avensis

thank you sir

I have a question, I need to replace my disa valves both upper and lower, on my BMW E92 325i 2006. The car has only covered 48000 miles since new, however the car is hardly used as i travel a lot thus i fear some parts will deteriorate over time, thus renewing before needed. I have elected to use Febi Bilstein disa valves which i feel are as good as the OEM units, what nis your opinion? on these parts. As said parts i feel fail too because of non use and a case in point the water pump last year, luckily it failed at home so i could replace it without any need to be towed home. This was replaced with the same make as was removed from engine a Pireburg, not correct spelling sorry.

Awesome.

Selam flap açık nasıl kapatabiliriz?

I have n52 and no disa where yours is located. Please help.

If you hook up a laptop with inpa software while the disa is removed but still electrically connected, you can operate the disa and see if it is opening and closing correctly on a consistent basis. Mine looked fine and worked fine most of the time. But when testing with inpa software, i could see that sometimes it would not fully open or not fully close. So will be replacing mine with a new Febi one.

@GeorgeAusters

4 жыл бұрын

Yep, I replaced the small DISA for a Febi one if you haven't seen the video

@seanpaul3050

4 жыл бұрын

@@GeorgeAusters Yes I will test the small disa valve with inpa too, when I get a chance. Although I believe the small disa operates at the high end of the rev range and thus sees much less wear than the big disa. So in theory it should last a lot longer than the big disa valve.

@ramazancivan2070

2 жыл бұрын

Nasıl bir yazilim nasıl bulucaz

What’s the ccv? That caused the leak

Hi Big DISA IS NUMBER 1?i have fault 2AA8 variable induction manifold 1 actuator😑

Thanks for the great tutorial! How/with what did you clean the throttle body?

@GeorgeAusters

4 жыл бұрын

Just needed a wipe as it's only oil

Hi George. Excellent video! This one and the intake manifold removal have been absolutely invaluable lately! I have a 2005 130i and have been having very similar issues to you... Developed a major rough idle this month (still not resolved but I think I've found the culprit..) and then the starter died totally last week so it kinda forced the issue and the intake manifold had to come off. Starts super quick now, valeo unit is a peach. However - upon manifold removal, something was rattling around in there which turned out to be half the flap off the large DISA! yes half! Which was worrying to say the least. I had taped up the intake ports on the head to stop anything falling in - the irony was the other half of the flap was sitting inside cylinder port #4 ! The flap had cracked in 2 straight down the spindle and the spindle had cracked off too. My car is on 90k miles and so yes, these disa valves can most certainly end up in the engine! Lucky that the starter died, really, so I had no option but to take the manifold off.. It doesn't bare thinking about. I guess the car was trying to tell me something! New DISA should be here tomorrow. Hopefully that will sort the hideous rough hunting idle (I put the DISA back in without the flap just to test had fixed the starter and that everything had been reconnected ok.) I'll update you when I get the new DISA in as it might prove useful to someone, who knows. Failing that, I'm thinking vanos / check valve cleaning may be in order. Thanks again for these vids. Super helpful to see someone else do it first on exactly the same engine. All the best

@GrooveDigger808

2 жыл бұрын

By the way, the hunting idle (which is now worse with the old DISA back in with no flap at all, than when half the DISA valve was still in there...) which shakes the car and feels like it's going to stall - settles right down after the initial open loop start up, completely disappears and becomes totally smooth, after 2 or 3 minutes. Very odd! No codes (except AUC sensor, bizarrely enough) I'm very keen to find out if it's totally down to the broken DISA ..

@GeorgeAusters

2 жыл бұрын

You’re welcome man, glad to be of help. Yes these engines need all the common problems fixing at the same time👍🏻

@GrooveDigger808

2 жыл бұрын

@@GeorgeAusters So, to update.. the rough idle which persisted after replacing the broken large DISA and entire PCV system (while changing the dead starter) was caused by - an air leak. Of course. I smoke tested the intake using a £7.99 transfer pump with a cheap cigar in the input. Worked an absolute treat! found the leak within minutes, one of the PCV hoses, the oil return, was disconnected. It was a right pain trying to reach to connect this tube when putting the intake manifold back on, I had decided to connect the lower end to the crankcase first and fit the top to the PCV while repositioning the intake. That was a mistake, it was incredibly difficult to reach at that point but I thought I had managed it. However, the starter cable pulled it off as it was being refitted into place, as it was routed the wrong side of this cable, which wasn't obvious while putting the manifold back on. If you're doing this job definitely fit the top end first, the lower end is way easier to do afterwards, believe me. So it turns out the original rough idle condition was caused by the big DISA with the totally broken flap and/or the PCV, which was letting a lot of oil into the manifold, so certainly needed replacing. Running sweet again now!

hey bro i got a 2011 bmw 328i N51 motor i keep getting miss fire on cylinder 3 i already change 6 new coil and 6 new spark plug / clean both vanos solenoid / change air filter / clean the MAF / change oil and filter / replace valve cover gasket / and i still got a missfire sometime is random muilt missfire and car run rought plus rpm keep going up and down idk what should i do next?

@GeorgeAusters

3 жыл бұрын

Tried scanning with ISTA?

Hi George, lots of wiggle room in the E61... if I pull this for inspection (I'm getting a 2AAB code) do I have to replace the seals (O-ring?) if it looks fine? Thanks in advance ☺

@GeorgeAusters

2 жыл бұрын

Pretty sure the seal is a part of the DISA so no way to replace it

Czy uszkodzona disa może powodowac pukanie

Thanks for the link where to buy the disa valve. They are the cheapest that I have found in Europe. Even I who live abroad save almost £80 when importing this part myself.

@GeorgeAusters

3 жыл бұрын

Glad to hear my friend!

Hi amazing tutorial do you need to take the Manifold off to do the small one thanks

@GeorgeAusters

2 жыл бұрын

Nope, I have the video on my channel👍🏻

How dirty was the throttle body ? I cleaned mine and the idle was so much better after cleaning.

@GeorgeAusters

4 жыл бұрын

No too bad, just had a smear of oil on👍🏻

Meanwhile my mechanic said it was a very difficult process to do it, so he charged me 4 hours labor time for time. Nice. I know I'm stupid, but I thought he was straightforward with me, next time when he says that I'll ask him about this DISA thing.

@GeorgeAusters

Жыл бұрын

Show him this video

Tonight I removed both Disa valves using your videos (because I had 2 fault codes in my last week purchased 130i😭) and found out the outher largest disa valve is broken, the inner smaller one looked fine and has no slack, but you think I should replace that one anyway?

@GeorgeAusters

3 жыл бұрын

I’d replace both yes👍🏻

@Blurky82

3 жыл бұрын

@@GeorgeAusters Tnx, might as well , i'm throwing money at it anyways now to make it drivably...

When you put the big disa back in, the flap was shut. I thought the default position with engine off is for the big Disa flap to be open ?

@GeorgeAusters

2 жыл бұрын

Yes but you buy them closed

My 07 BMW e70 3.0si went into "Reduced power mode" but when I restart the car everything went away. I checked with the OBD and it said 2AA9 error code. It means my DISA is dead, right? Thank you

@carcosatone7465

10 ай бұрын

I have the same code on my 2005 e90, 330i. Did replacing disa helped you?

@QuanNguyen-vi1fi

10 ай бұрын

@@carcosatone7465 yes, it was broken and while I was there I found oil in eccentric shaft sensor and intake manifold. It was caused by broken ccv.

Hi George! Is it true that last generations of this DISA (which you probably had in this new one) has aluminum rod (not a plastic one)? TIA,

@GeorgeAusters

Жыл бұрын

I’m not sure sorry

@romanjacobs1794

Жыл бұрын

@@GeorgeAusters Oh, OK. And how long they've been holding up?

@mauritz9691

Жыл бұрын

Yes, the new one has a metal rod and the Febi one also does (I just checked it with a magnet)

👍🏼

So the n52 without the 3 stage dont have a disa under the manifold?

@GeorgeAusters

Жыл бұрын

Correct 👍🏻

All you had to do is loosen the band clamp on that last section of intake at the throttle body. I literally just did that

@ears1991

Жыл бұрын

great tip, thanks! saves needing to worry about throttle body gasket

Is 2AAC the big or small disa?

@Blurky82

3 жыл бұрын

I had the 2AAB code and that was the big outher one, but it could possibly also be the other one. The large one is not very hard to remove, takes about 15/20 minutes.

I need to replace both of mine (2008 125i) any ideas which parts I need exactly? Thanks

@neo61uk

3 жыл бұрын

125i and 325i have no Disa valve.

@craigroberts3732

3 жыл бұрын

@@neo61uk They do actually LOL

@neo61uk

3 жыл бұрын

@@craigroberts3732 yeah you're right. For some reason bmw in all their wisdomnes decided to use n52 engine in 2008 125i, but same year 325i is n53 (no Disa valve) 🤦🏻‍♂️

@craigroberts3732

3 жыл бұрын

@@neo61uk yeah but it is a great engine and i love it in this car .. only downside is the cost to maintain it

@neo61uk

3 жыл бұрын

@@craigroberts3732 sure, good engines, n53 great engine too mate but have no disa valves to worry about.

What’s going on with your e60

@GeorgeAusters

4 жыл бұрын

It’s under construction👍🏻

Has anyone here ordered the FEBI DISA from the link in this videos bio (fixpartsonline) to the USA and if you have how long it did it take to arrive, is the part reliable, and is the shipping process smooth(customs charges?) please let me know! Because Im in a big need of this part but not looking to pay Bmw’s hefty 400USD/600USD price tag for this small plastic part. If somebody from the US has ordered this here please reply and let me know 🤞🏽

@GeorgeAusters

3 жыл бұрын

Should give you an estimated time when you’re on checkout. Choose express shipping to get it faster👍🏻

@spyderx2381

3 жыл бұрын

@@GeorgeAusters yea that it does, but the expedited shipping is way to exepensive.. making it less worth ordering I want to get it to save cost as much as possible but still receive a trusted/reliable paart the thing Im most concerned about too is if it will have any extra charges at the boarder ?? You went with the FEBI-DISA for your smaller disa right ? How is that holding up and how come not go with the FEBI-DISA for the outer(bigger Disa) aswell if you dont mine me asking ?

it stuck man how it is good condition , if you split it for two pieces you will find it full of oil

Do I have to pay for this advice ?

@GeorgeAusters

4 жыл бұрын

Of course my friend, BMW will charge around £500

Could this solve 2 lean bank errors?

@GeorgeAusters

3 жыл бұрын

Depends if this is your issue

@Magic4599

3 жыл бұрын

Did you solve the 2 lean bank errors ? I had a code like that. I finally got the oil leaks done. The serpentine belt pushed in the crankshaft seal. The code causes us to think it's an electrical issue, when it's an air leak. In my case, crankshaft air leak.

@walletphonekeys

3 жыл бұрын

@@Magic4599 how did u find out it's the crankshaft leak? I still have the and I first thought was o2 sensor, or maybe even the maf

@Magic4599

3 жыл бұрын

@@walletphonekeys the oil filter housing gasket leaking oil on to the serpentine belt causing it to break and rap around the crankshaft, pushing in the seal. First I thought the leak was coming from the oil pan gasket. Interestingly I found pieces of the serpentine belt in the pan before it clogged the oil pump. Maybe both were leaking oil, before the belt broke and trashed the crankshaft seal.

Yes yes

@GeorgeAusters

4 жыл бұрын

Do you want to see more videos like this?

@mrboostification

4 жыл бұрын

@@GeorgeAusters Yes bro, I got the same engine 258hp 530i

@GeorgeAusters

4 жыл бұрын

Awesome man glad to have you here🙌🏼

Removing the intake manifold has never been necessary to replace the large DISA. The opposite for small DISA tho.

@GeorgeAusters

8 ай бұрын

Don’t need to remove the intake manifold to remove the small one either.. watch my video replacing it👍🏻

It is never a good idea to cheap-out on any part for a BMW.