Well done. Thank you so much for sharing this video.I have problems with mine at the moment too. I have only 10volts in the cigarette lighter and the display comes on and off but the car still starts.So I will remove but junction box and have a look too. I suspect it is the burned out battery cable.

Nice video specially when it shows the same symptoms as i have on my car , good job , gracias

Thanx very much your video helped me with my e92

Its funny.... my fusebox has exactly same problem. Where is from this water or something? Thanks for video, you helped me to do it myself :)

my BMW had a lot of moisture in it, do you think that could have caused this problem? every light in the dash is on and it won’t even try to crank

I had the same problem! Sometimes my car (E93) had no electricity at all! After a while it came back and everything worked normal again. Until next time where it happened again. In my car it was "only" the power cable that had a loose connection. Thanks man for your video. It helped me very much.

Thanks for ti.elapsing past the entire how to

Having the same issue on mine, going to pull mine out, hopefully goes well thanks for the video 👊🏽👊🏽👊🏽💪

@trendntopikk879

Жыл бұрын

Same here it was driving fine one day parked at dollar tree didn’t turn on changed the battery but I get a increase battery discharge and lighting warning

Great video man! I have just pulled mine out too,but it all looks fine really,I have bought another used unit but I suspect my junction box is faulty,shows up as (A738 power supply),but some things work and others don't,climate control is dead,shows no fuel in tank,wipers have a mind of their own,and no remote locking at all,starts and drives fine,checked the battery,had a new one just fitted and all connections are fine, radio did work but now no sound

@WarpDriveM

5 жыл бұрын

Battery has to be coded after replacing. Junction box and fuse box after replacing must have the jumpers in the same location as the original one otherwise it won't work properly! It won't power all the modules! Maybe for the central locking you have to change the battery in your key fob.

@graceyjack

5 жыл бұрын

@@WarpDriveM Thanks mr and for quick reply too,i'll check that out too

Grüße, hast mir sehr geholfen DANKE

Do you have to change the entire fusebox? If its just lose, why not use washers to tighten it?

Hello I’m getting code junction box A731 (Supply, terminal 30g-f) I changed the 30F relay but no luck. I have a brand new battery, the car turns on and runs. The only issue is when I leave it on accessory for maybe 3-5 mins my battery gets drained and I cannot start the car, I end up using a jumper box to start it. Can the junction box be the issue causing this? Or could it be the fuse block on top of the battery. Thanks let me know what you think :)

Question, how did you access the one screw holding junction box behind blower unit? Did you remove blower? If not, wow, not sure how you access that screw. There are four screws, correct? Thanks

@WarpDriveM

5 жыл бұрын

After you remove at least 2 screws you can rotate the fuse box enough to have access to that screw. A little bit tight but is doable

@GuestU2

5 жыл бұрын

@@WarpDriveM , I think using a 1/4" extension 6" with swivel and T20 will work at a 45 degree angle for the top left screw behind blower. Or, maybe just remove blower ot make access easier.

Dude u didn’t show us how to disconnect all the wires that’s what I am stuck on. U just fast forwarded everything

Great, thanks for the video

excellent video

Hi mate, thanks for the video, What was the main problem to make you change the junction box I have the same thing in 5 Series 535 F10. I'm not sure if I need to change some fuses all the whole junction box🤔?

@WarpDriveM

4 жыл бұрын

It was cutting all power off and the car wouldn't react to anything...

@ibrahimsharif1067

4 жыл бұрын

@@WarpDriveM mine come on the ECU with a junction box error but no other fault the car starts fine thanks again

@WarpDriveM

4 жыл бұрын

You can reset the error to see if will come back on. if yes you might check the battery

do you need to do any programming after changing fuse box (junction box). My mechanic told me need to do the programming which i was suspicious about

@WarpDriveM

5 жыл бұрын

If you change the electronic module as well and not just the fuse panel then you do.

Nice video.. Thx. I have the same problem right now.. What is the part number for fuse box?. I have an e90 320i, wondering if is the same part for US 328i.

@WarpDriveM

3 жыл бұрын

Normally the fusebox is the same just be sure you have the one for facelift model (from 2010 till 2012) or pre facelift (2005-2010) depends what car you have. Part nr is written on your fusebox. This is part nr for a fusebox facelift model 61149119445. Check jumpers and everything when you make the swap

That’s not the junction box. But nice video dude.

MY E90 is also dead similar thing..man thanks for this video

Nice job

My wife's BMW 3 series has a fuse box ( distribution)box problem, in that the horn no longer works and the remote door opening no longer works. In the UK no horn means immediate failure of the road worthy test and therefore dead car. Labour rates for an auto electrician in the UK,sky high. Total dead car as not economic to repair.

Easely to watch, hard to do :)))) Ce s-a intamplat cu acea mufa de cablu, ai schimbat-o si pe aia? De unde ai cumparat sicherungskasten? Danke für deine Antwort! :D

@WarpDriveM

6 жыл бұрын

Mufa am strans-o doar ca nu se poate schimba. Trebuie tot cablu de la baterie schimbat. Cutia de siguranta comandată de pe ebay.

Hallo, wie hast du das Den Batteriestecker da rausbekommen. Ich wollte nur den Batteriestecker rausbekommen und dann die Metallteilen etwas mit der Zange biegen bzw. säubern. Aber ich bekomm den Stecker einfach nicht raus. Liebe Grüße

@floriankirchner-qx4ye

6 ай бұрын

hey und was war. das problem?

@singhsarabjit

4 ай бұрын

I am having same issue? Don't know how to take out battery positive cable from back of fuse box? Thank you G

Hi mr.Warp , Please do you have a diagram for the Jbox E 90 2008 I'm having a problem, with a no start...symptom no MDE RELAY * ...NO DDE RELAY * Thanks in advance Regards 👍😎

My car starts in runs it just does get power when I hit on my gas to where I have to pull over to start it up again but it runs can sb tell me what’s wrong with my car I changed the spark plugs ignition coils

Wondering if I need a new JBE module. 2012 E70 Diesel. Had low battery warnings while inside car adding features to my Android screen. I then lost power to Steering Column tilt and all Climate Control. Carly adapter OBDii error codes are saying timeout at JBE box. The error codes are difficult to find info for. -- Systems error = Junction Box Passenger: K-CAN MESSAGE (ID2BF, VALVE): FAILURE BY TIMEOUT, Code 00A737 -- & -- Junction Box Passenger: PT CAN ID2A6 OPERATION WIPER TIMEOUT / K-CAN MESSAGE ( ID 246, STATUS AIR): FAILURE BY TIMEOUT, Code 00C914 Any help greatly appreciated!

@WarpDriveM

5 жыл бұрын

All your errors are most likely because of your battery. You have to check the battery and after that to start changing parts. I'm pretty sure that the battery is faulty

@PolskiDangles

5 жыл бұрын

@@WarpDriveM Thanks -- Pretty certain 99%, the battery caused these issues. But (too bad) a new batt did not fix. $80 JBE arriving today and going to let my local BMW mech install since he has the computer tablet to code it to my vin... Not sure if installing first, then driving it over to get coded is a good idea? Does the JBE need to be "IMMEDIATELY" coded? Hard for intermediate DIY'er to predict any possible trouble doing that.

I have a lot of problems with Terminal 15 no communication. Do you need to program the junction box after the replacement?

@WarpDriveM

Жыл бұрын

If you are replacing just the fuse box itself and reuse the junction box you don't need to reprogram anything but if you are replacing the junction box as well that needs to be coded

@Lu-e

3 ай бұрын

@@WarpDriveMhow do you code it if you’re using protools?

hi i have bmw same proplem . can you till haw i open tha kontakt for cable? becus the cable in may car vary hard

@WarpDriveM

4 жыл бұрын

There is a plastic piece on top of the connector you have to press it towards inside and it will release the cable. It is a little bit hard to do but thats the method

Do i need to clear the errors at the final with a diagnose ? Thanks if you answer to me !

@WarpDriveM

Жыл бұрын

Yes you need to clear the errors

Can angone tell me which year the recall was..i love these cars ive had four and really hope i can get ut fixed theyre awesome cars til something tears up and then its gonna cost you

@WarpDriveM

4 ай бұрын

The battery cable is a recall for all e90. You can check online if your car has an open recall or not. Google bmw recall put your vin nr in there and you can see if there is an open recall on your car.

What year is your car ? Because I know this model had a recall due to the electric fault

@WarpDriveM

3 жыл бұрын

This was 2010 model year, you are right a out the recall but sadly not in Europe

My OBD port don't response, did I need to change just the junction box ? Or the module with ?

@WarpDriveM

4 жыл бұрын

Obd has a fuse as well. Check the fuse and when obd is not responding usually is the FRM module bad

@AteshAhmedovic

4 жыл бұрын

@@WarpDriveM Is it possible my junctionbox is almost dead ? Today everything was perfect, no fault, nothing wrong. But this night, whole fault come back.

@tshepisosebetola614

9 ай бұрын

@AtenshAhmedovic Hi did you fix the obd port if so please assist i am having the problem with my e90

@AteshAhmedovic

9 ай бұрын

@@tshepisosebetola614 Yes it works. I didn't do anything. I just reinstalled the software on my computer.

This fuse box problem was the subject of a recall, first in the US, then in the UK. The replacement fuse box has a completely different connector for the main battery connection; a bolt an nut requiring an 'eye' connector on the battery cable. The BMW kit includes a replacement section of main battery cable to match the new fuse box. The old main battery connection is completely unsuitable for the current flow and overheats as shown in the video. The recall in the UK only happened after a BMW e90 driver was killed in a collision when their car died on on a dark road leaving them stranded.

@WarpDriveM

4 жыл бұрын

You are 100% correct! But at that time there was no recall. I've sold the car and I've bought another 3 series a gas one and it was done as recall problem. On diesel models just from this year will be done as recall problem....

@wytzzmf

2 жыл бұрын

Last weekend, same happened to me. Whole engine cut off electricity while driving. I even could not turn the hazard lights on. I was on motorway doing around 50mph. It was so difficult moment, and the electricity come back after 2-3 seconds. I took the car to BMW Sytner in Leicester, and wanted them to have a look to connection. They had a quick look, and told me it looks fine... However, now I do not feel safe. BMW did change no part, and told me everything looks fine. I could have also passed away when the electricity shut down. I think BMW recall should have also included replacement of the fuse-box, not only the cable! I am currently preparing for enough evidence to take a legal action if this fault turns out to it is caused by same fault. If you are interested, please see the discussion on the below link on forum; www.bimmerforums.co.uk/threads/i-almost-die-2dec-fault-code-voltage-issue-loose-wire-connection-on-junction-box.583474/#post-3343191

@danacollins8367

4 ай бұрын

My cars doing this too and despite what my boyfriend says I think it's from this recall I drive the car daily and I am more familiar with how it's doing and it's not the battery like he says..I stay this bc it's almost like there is a wire loose and it's only done this twice but both times he jumped it off and both times it didn't seem to be working when he jumped it off until he wiggled the cable then it just lit up I am a girl and most girls aren't good with cars I'm no exception but I'm not dumbass either and I have a feeling it's not the battery

Did you need to disconnect the battery before removing it?

@WarpDriveM

4 жыл бұрын

If is already broken it doesn't matter...but normally battery should be disconnected always when working on electrical parts.

@dragomirgo9199

Жыл бұрын

Yes, remove the black (negative terminal) cable only

My BMW 318i not starting. The fuse box was Bern. So hi get a new one on it still not starting why?

@WarpDriveM

5 жыл бұрын

Check if you put everything the same in the new fuse box as in the old one including the jumpers

@lionden9601

5 жыл бұрын

@@WarpDriveM what is the jumper?

Hey, richtig gutes Video. Ich hab exakt das selbe Problem. Mein Englisch ist jetzt nicht das Beste, dafür auf deutsch: Hast du alle Elektronikteile vom Original auf die neue „Platine“ eingesteckt? Ich meinte ich hab was gelesen, dass man das dann nochmal programmieren muss.

@WarpDriveM

4 жыл бұрын

Ich habe nur die Sicherungskaste gewechselt. Dafür muss man nicht neu programmieren lassen. "junction box " steuergerät müsste programmiert werden wegen ausstattung... richtig aufpassen bei Sicherungskasten das jeden Teil genau wie früher ist und auch die "jumpers" Brücke Verbindung genau sind. Viel Glück

@alawstory2520

4 жыл бұрын

Warp Drive M danke für deine Nachricht. Weißt du vielleicht, ob man nur den schwarzen Stecker vom Batteriekabel auswechseln kann? Ich weiß nicht, wie der Stecker heißt? Weißt du es vielleicht oder hast du eine Teilenummer? Liebe Grüße

@brucewayne4360

4 жыл бұрын

Hy ...musste auch die junction Box tauschen nur hab ich es bei BMW machen lassen ... funktioniert bei dir wieder alles ?

@alawstory2520

4 жыл бұрын

Ich war mit meinem Fahrzeug bei BMW. Die haben das checken lassen und meinten, dass mein Fahrzeug davon nicht betroffen ist. Die haben auch an dem Kabel gerüttelt. Und der Wagen ist nicht ausgegangen. Letztenendes war die Batterie defekt, weil die schon zu Alt war. Die wollten allein für die Diagnose 90€. Abzocker. Aber das war jetzt mein letzter BMW. Ich Wechsel zu Mercedes.

hello I have a problem with my E90 I have an electrical failure nothing that turns on the doors I have to open them manually the dashboard is off if you know help me a big thank you

@WarpDriveM

3 жыл бұрын

Check this video kzread.info/dash/bejne/jH2K2rVxe9OWg7w.html this might be your problem

the moisture is from the bad seals in the cowl

That’s not the junction box but nice video

Did it fixed the problem permanently.

@WarpDriveM

5 жыл бұрын

Yes. No problems since I change it!

Where can i buy a new fuse box for my e60?

@WarpDriveM

2 жыл бұрын

Ebay, Amazon, Bmw, just Google it or search fusebox bmw e60 on eBay/Amazon

You didn’t have the key fob in the first time you tried to start it after you replaced the fuse box .lol:)

@WarpDriveM

2 жыл бұрын

The car has keyless go/entry. I don't need to use the key. You just have to have it in the car. You can pit it in the slot as well...

I have a BMW x1 e87 but total electrons have been blanked, nothing is going to show

@WarpDriveM

5 жыл бұрын

Just try to shake the fuse box or check cables on the battery!

@golamsarwaralamsiddique2617

5 жыл бұрын

Warp Drive M I have tried several times but there is no profit, Just lighting the lights but there are nothing shows in the display

@golamsarwaralamsiddique2617

5 жыл бұрын

Warp Drive M actually Due to rubbing of rats, the water was submerged under the fuse junction box

когда турбо ?

Need to remove error codes or coding? Thank you.

@WarpDriveM

4 жыл бұрын

For fuse box no coding required but if you replace the junction box sometimes you need to do some coding if the new junction box came from a car with different options

@hunbrian6138

4 жыл бұрын

@@WarpDriveM Thank you for your fast reply.

Had the same issue but i had to change the battery 😅

I hope this work for me , I'm crossing my fingers!

@WarpDriveM

2 жыл бұрын

If you have the same symptoms this might work because this Is a known problem on this cars....have fun 🙃

@theophilusone7

2 жыл бұрын

@@WarpDriveM ended up being my eccentric crank sensor. 256k miles and still a fun car to drive.

This dude forgot the key that's why only the lights came. It only came when he pushed his key in wow lol

Just to add on to your issue. If the Integrated Supply Module in the Engine Hood Passenger side fuse blows off also this could happen. I managed to break in to that one too. Might benefit someone. Here's the Link kzread.info/dash/bejne/m4Z_zdCMlardj7g.html

@Seredinh

Жыл бұрын

The difference is, if you shake the 12v cable behind the glovebox and everything works, it is not an ISM module, it can also be IBS on the battery though, but then you have totally no power.

@bimmerhacks

Жыл бұрын

@@Seredinh is the 12v cable connector faulty!!! I have ripped the glovebox fuse box too and saw irreplaceable fuse and some small relays. I have posted it's video, I don't know if it will help out or not.

@Seredinh

Жыл бұрын

@@bimmerhacks I believe I also have the same issue now. Sometimes the car can go for days without problem, sometimes I totally have no electricity.

@bimmerhacks

Жыл бұрын

@@Seredinh rip it open and if you find anything wrong change it.

My bmw there's no power by the petrol pump and or the fulse is fine I and have replace the petrol pump

the cable is faulty in the us we got a recall mines still broken because they didn't replace the cable but they said they did

@WarpDriveM

5 жыл бұрын

In Europe we didn't have recall for this. Recently I've bought another e90 328i from US and for that they've done it. So just the US market can do this faulty cable through recall.

@TEAMCREAM_96

5 жыл бұрын

@@WarpDriveM i wonder why they didn't recall it over there

@WarpDriveM

5 жыл бұрын

I think because we have different options on the cars and different engines and for that the cables are different routed. And the percent of the faulty cars is way smaller the in the US market. Just my opinion....

Why didn’t u go slow motion on how to take it out why would u make it go so fast.

The error was?

@WarpDriveM

4 жыл бұрын

The fuse box. But the main problem was the positive cable that came from the battery. Now it's a recall from BMW. If you have this problem you can call your bmw dealership to see if they are gonna fix this for you (free).

@SirGipsy

4 жыл бұрын

Warp Drive M Fault code: P0056 Fault code: P0130 Fault code: P0160 Heated Oxygen Sensor Heater (HO2S) - Circuit Malfunction (Bank 2 Sensor 2) O2 Sensor - Circuit Malfunction (Bank 1 Sensor 1) O2 Sensor - Circuit No Activity Detected (Bank 2 Sensor 2) Can you help me? PS: i have change the all 4 sonda lambda the error dont go away."Reset to" Bmw 320si e90 n45 2006 Check engine on.

@WarpDriveM

4 жыл бұрын

That seems to be a wire problem. You have to check the wires between the firewall and the engine. There should be a metal holder. If that is gone it might be that your wires are burned from the exhaust

@SirGipsy

4 жыл бұрын

Warp Drive M do you have a video about this?

@SirGipsy

4 жыл бұрын

Warp Drive M do you have a Facebook Page?

Are you buying another BMW?

@WarpDriveM

6 жыл бұрын

Yes. That's the plan at least! 😁 or depends on what offerts I find on my expectations. But first I will looking for BMW.