just noticed this wasnt part of your e46 manual swap playlist. thanks Jason for gold content as always

I recently swapped my engine from n42b20 and automatic transmission to manual on my e46 2003 convertible and it's thanks to you and your videos I'm really thankful that your videos exists on youtube Big up ! 🙏

Like the way you describe details such as the clutch fork retaining spring and why to lightly & carefully grease certain points avoiding too much grease that might affect the clutch plate…good stuff as usual! 👍

This is the video that i was waiting, just about that zone. My gearshift has some slack and now i know i what the worn pieces are. congratulations your gearshift is been new !! regards from spain.

thanks this helps a lot to get the full visual of what i need to do to get the short shifter in

I had to leave the washers out when I updated the new linkage bushing, everything was nice and tight.

That is a cool clamp. Wish I had that for the caliper slide pin protective sleeves.

Thanks for sharing this with us.

You did like me and didn't replace that $6 selector shaft seal on the tranny. I'll do mine with the rear main. I did a short-throw with an OE 535i shifter, already had an M knob. That idler arm rear mount new and old seemed the same to me, LOL. On the front of the idler arm I used the nylon bushings from ECS to tighten it up even further.

That Bushing That Slides Right Out I think it’s called the shifter arm bushing if there’s not one on the trans the shifter will drop from it’s correct position right u would have to hold it up while shifting ?

Can you do a manual swap of the shift bushing when the transmission is still in the car?

Great idea

what if it's not going in gear? with brand new clutch and flywheel

How do I take it out?

If I was doing this swap,and putting a oem short throw shift kit in...would I be replacing all this anyway?

Great

Do you happen to know anyone that can program my e39 after a manual swap around the valley? Thanks

Hey man, I'm doing the 5 speed ZF manual swap in my 2002 330i . The donor car was a 2002 530i and I'm noticing my shift arm is different than the one you have. Do you happen to know if they are interchangeable? Thanx

I’ve seen it done but expect to spend many extra hours doing it. There are YT vids on it.

Hi just wondering is it possible to do this while the transmission is still in the car , thanks

I’d like to change the bushings only without taking the trans out. Is it possible

Few tips: use the appropriate grease, lithium spray is too light duty and won't last. Don't use silicone spray to push in bushings, glue like substances are actually specified as bushings should be fixed in place and lubrication weakens the hold.

Hello do you know if in a 1999 e46 320d, the transmission is the same as yours?

in the future get the delrin bushing for the front and the poly one in the rear with a z3 shifter and if u really want get a dssr and ur shifter will be perfect

@victoraugusto3610

6 жыл бұрын

Do you have these on your car? Does the poly one in the rear add any noise, vibration or harshness to the ride/shifter?

@mike.135i

6 жыл бұрын

which model z3 shifter? any of them?

I have a question

Nice

Thanks for the video. I really learn a lot from your nice videos. I have a question. Recently I replaced some of the bushings except the rod joint. Now shift lever lies slanting towards right side. I noticed that the selector rod is inserted from the right side (passenger side) but I inserted it from the left side. What could be the reason?

@tommyriffe9115

2 жыл бұрын

5th gear lean

@Wishnuful

2 жыл бұрын

@@tommyriffe9115 Thanks

Is this repair kit compatible with e90 2006?

did this fix actually solve a sloppy gearstick?

@garrettgiuffre7298

3 жыл бұрын

If yours has never been replaced there's a few factors the if the selector rod bushing is worn it'll create slap if the rear shift bushing is worn it'll create play if the shift rod ball is worn it'll create play if the shifter ball cup is worn it'll create play if the front oval bushing is worn it'll create play if they're all worn it creates a lot of play a perfect working order shifter will still have some play from the factory because it's not a race car but if you have a car that's never had any servicing of the shifter and it's $200,000 miles and you go from that to a complete replacement of all the shifter components it's night and day add a short throw shifter and maybe a zhp knob maybe polyurethane bushing for the rear big difference big big big big difference nachi

Good video, but does it address clunking noise when pressing the clutch which usually happen in bmw z3 manual or e46 manual cars?!

Is it possible to replace the shift lever bearing without removing the assembly from the car, or getting underneath? Could I do it all from the cabin?

@jasonputtock4428

5 жыл бұрын

no. you need to lower the transmission by 4 inches. Then remove the lever from under the car.

hei there! you really do great videos. i was posting in other videos. so i changed the gear mounts and the gearbox stick still shakes a bit. im guessing i have to do this repair like in the video? looks like a bit hard and expensive.

@50sKid

6 жыл бұрын

Nah this repair is specifically for a shifter that sticks when you move it over into 5th gear.

@northeastgiants775

4 жыл бұрын

rulerss guibo is worn

@angeloszagoris7418

4 жыл бұрын

50sKid i have a problem with my e46, cannot engage reverse, sometimes it goes in but most of the time i have a problem engaging, any ideas?

Can you access and take out the shift lever to replace the bushings without dropping the trans?

@haroldramislives

3 жыл бұрын

I also need to know this. I was literally driving to the garage this morning to get parking break fixed when all of a sudden my stick went slack and now my car is stuck in second.

@evancrawford5997

3 жыл бұрын

I know I’m a month late but yea you can, it’s a tight fit for the clip that holds the upper link on but it can be done with a screwdriver, you may also need to remove the driveshaft but it is completely possible to reach around and work with the shifter

hi 50s kid I want to know why my shift gear don't want to go into gear when I started engine but if I put in gear and started engine the car will roll with the clutch fully press do u what's wrong or what I need to replace?

@BlackJackGarage

5 жыл бұрын

Sounds like a clutch bleeding problem,either you have air in the system,or if it's run by cables they maybe got loose so your clutch doesn't disengage completely.

@mrs.w.4618

4 жыл бұрын

Hi... My car is doing the exact same thing. Very very hard to get in gear when running, but f I turn it off it goes in no problem. My car also rolls when in first with clutch fully engaged. My clutch pedal also has about 3 inches of play... Any ideas?

dude i pushed the bushing off and on easy with my thumb. you should only have a yellow spacer on the outside. thats why it would not fit.

@50sKid

6 жыл бұрын

No spacers at all with the new bushing I installed--it has integral bushings. Says so on realoem, in fact.

I don't know why I always watch other people's videos trying to look how to do something for hours and hours and get so frustrated and pissed off because they're all so much idiots that think they know what they're doing that regurgitate information and I always end up back here to the fifties kid and say wow why didn't I just do this first because you know what you're doing Dam it

Just for the sake of it, I put a dab of grease into the cushion foam since it will rub endlessly.

Would've loved to see the shifter removed while on the car. No one seems to have a good video of them actually removing that bitch clip without dropping the Trans or removing the drive shaft

Always replace that pivot point on the throw out rocker.

@ts-vu3dd

4 жыл бұрын

For this car atleast it can make it rattle in some cases

Beware: if your throwout bearing has a plastic sleeve you are not supposed to grease the sliding tube!

You definitely want to replace the pivot pin.

@50sKid

6 жыл бұрын

you talking about something I did not replace or that I did?

@cngzsn

6 жыл бұрын

50sKid The one that you said you didn't get a new one. The head on that pivot pin wears out evenly, so it "looks" ok.

@50sKid

6 жыл бұрын

Ok--I didn't feel any clearance in the pin after I had reinstalled it though--I think it's ok.

@E46TY

5 жыл бұрын

50sKid not where it installs, where it touched the clutch fork

I wish you were my brother

Are these bushings only for manual transmissions ?

@RidwanMaassarani

6 жыл бұрын

In terms of the rear bushing only

@50sKid

6 жыл бұрын

yes

video could have been 3 minutes long

niqqa

Question is, how the FUCK do you get this shit off when its on the fucking car