I wanna cosplay like hawks for bnha and it so cool so I'm gonna make a huge version of this

@marialchrz768

3 жыл бұрын

I was looking for a solution to make my hawks cosplay, and i just saw your comment first, made me laugh a lot

THANK YOU. I hope you could add some audio instructions or tips in the next videos :)

Please upload a video of step by step because all are slow learners

Quito Ecuador excelente trabajo

How would you put it on your back and still make it move

where can i get the blueprints?

Blue prints please

SERIA BUENO LOS DIAGRAMAS AHAORA A HACER CAPTURA DE PANTALLA

Are you selling the pdf/blueprints?

How do i print it though? I would like to make very large ones so how do i print them and how do i make it so that i can spread the wings from the front

@ChefWant2Be

4 жыл бұрын

You may consider projecting the template on the paper in the desire size. Trace the outline with a pen, then cut it.

How do the other wings expand?

Do you teach classes?

Would this work sized up? Or would it be too heavy.

@pineapplz7162

3 жыл бұрын

Well, using a single layer of posterboard, the MAXIMUM practical width is about 8 feet (244cm) fully extended. The sizes of the spars and wooden arms in the various pictures of the larger set are the bare minimums needed to support the weight at that size, so they do flex a little. If you can source it, consider using ultra-thin corrugated cardboard for all or most of the sections, instead; the build would be easier. Double up the wooden arms and spars, if a bulkier look is OK. The pulley diameter is sufficient, but it could be made wider to increase leverage. Perhaps a more important consideration is that wings which are 8 feet wide across the top when open are 4ft (122cm) wide at the bottom when closed.

may I ask how one would go about making the feathers?

@pineapplz7162

5 жыл бұрын

Hi. Were you asking about the material and shaping of individual feathers or about a tutorial for the build overall?

@soundwave7502

5 жыл бұрын

@@pineapplz7162 i was interested in what the wings would look like before they were folded, how to fold them, and what they should look like when they're done. thanks

@pineapplz7162

5 жыл бұрын

@@@soundwave7502, see kzread.info/dash/bejne/lGucs5qcYqTOopc.html for a condensed sequence from template to assembly for one section of wing. Basically, the large set will look the same as the small model (identical blueprint dimensions), except the arc connectors will be made of wood, rather than paper.

I'd like to know how to do the wings in the same way as version 1 with the pulley system like just pulling a string and it extends I know that this is quite an old video but by far the most reliable.

@pineapplz7162

4 жыл бұрын

Version 2 is essentially the same system as version 1, but with a better pulley setup and different feather outlines. I don't show the strings anywhere in version 2, because the strings just feed through plastic pipe over the shoulders and pull up on the ends of the wooden rods. The new version is about 80% complete, and is 1.5X larger. However, it can be made at any smaller size. Recording all the steps in detail is a very slow process, but I'll post a tutorial when it is done.

@IAmDeadBread

4 жыл бұрын

@@pineapplz7162 okay thank you I'll make sure to turn on notifications then. I admire your commitment to this I don't have that much patience. ^-^'

@Zara-ZAF

8 ай бұрын

​@@pineapplz7162hv u uploaded

Watched it so many times, m too dumb to understand this

Do you have the map to download it'?' thank you

@moniquecarty4859

6 ай бұрын

Too small to fly right???????

Hi can i ask are you selling this?

@nerd3612

4 жыл бұрын

jabez jael del rosario mika

With is u don't have wood?then wha

👍👎