Regulator/Water Trap: www.amazon.com/gp/product/B07H2FPHK1/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07H2FPHK1&linkId=e57035dc25b2a8a06a55f2ca6817c7a9 Billet Air Manifold: www.amazon.com/gp/product/B07S6116PQ/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07S6116PQ&linkId=4cc72e2ec3817776e439d5b99791fedf Projecting Laser Level: www.amazon.com/gp/product/B073VJPM4Z/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B073VJPM4Z&linkId=3cb2e013382867ae528bfa8ecf92ea7d Pex Crimp Tool Kit: www.amazon.com/gp/product/B074K6R4D2/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B074K6R4D2&linkId=5a732b1e6bcbc13b1a5e077c85f07797 Pex Tubing: www.amazon.com/gp/product/B0088PYGQ8/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B0088PYGQ8&linkId=a78f61f0bef5ae770f9a9113815eb8b7 Shutoff Valve: www.amazon.com/gp/product/B01BTY6Q12/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B01BTY6Q12&linkId=c77cc41b665cbccf35b7a707e02e4e07 Quick Connect Fitting Kit: www.amazon.com/gp/product/B07Q9QS7BT/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07Q9QS7BT&linkId=ebe063401e8795e981dbb05edf52979e 1/2 Pex to 3/8 NPT Adapters: www.amazon.com/gp/product/B07CRTM8P7/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07CRTM8P7&linkId=5914b3da816e81bd059e76975dc5b421 1/2 Barb to 1/2 NPT to connect Pex to Manifold: www.amazon.com/gp/product/B07LDQQ86X/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07LDQQ86X&linkId=8264d423bcd2904bd84dc1340fb7670a Plugs for unused manifold ports: www.amazon.com/gp/product/B07BS8ZJHM/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B07BS8ZJHM&linkId=75ba6673ca3a04d20eef51b18041ad81 P-Clamps to mount lines to the wall: www.amazon.com/gp/product/B01N074XSY/ref=as_li_qf_asin_il_tl?ie=UTF8&tag=trialnerror-20&creative=9325&linkCode=as2&creativeASIN=B01N074XSY&linkId=3922890edc4200304dff3664a81c8879 BRAND SPANKIN' NEW CHANNEL MERCH! teespring.com/stores/trial-n-error Want MORE monkey business? Find me on Facebook: facebook.com/KZreadTrialnerror/?view_public_for=232815904127596 Thank you for watching! Please subscribe for future updates and check out my Facebook page for additional updates that don’t always make it into a video.

@ronesmith2770

3 жыл бұрын

I heard you say that you were putting in a Whole Garage run vacuum ?? If so I'm curious to know if you ever did it, what type, how it work etc ? I'm considering doing the same for a 3 bay shop. Thanks

@Trialnerror

3 жыл бұрын

@@ronesmith2770 Not yet. I do still plan to but I need to build a little utility room under the stairs first to put it in. As usual, I have more plans than hands lol.

@ronesmith2770

3 жыл бұрын

@@Trialnerror OK, and did you decide what type of vac your using, and pipe set up like pvc etc ?

Do a loop3/4in around your garage. Have one main line feeding the loop. Helps with volume, pressure and more drops

Hello: I live in the Caribbean (Puerto Rico) and have been toying with the idea of installing my own "Air Compressor System"; however, after checking out the many different systems available on line (all prohibited after adding shipping charges) and COPPER pipe is literally at gold prices, I started looking for something different and I came across this word "PEX"; after looking at YOUR video and comparing price, I am sold, it's the way to go (accepting modern technology), even if the idea has been around since the 30's; your video is very good, simple and cost effective and much easier to install, thanks for the idea, it works!

Nice, simple setup. Great job!

Sounds good. Once my shop is ready I think I'll do the same. Thanks for the video.

I love this. Thank you for sharing your thoughts and wisdom.

I've had 1/2" copper for about 20 years. Want to make changes but just didn't want to rerun copper again. This makes sense. I will run a 3/4" main line with 1/2" take offs.

Yup I had researched the crap out of using Pex like 7 years ago when I was building my house and couldn't be happier! It is super easy to change and alter if needed and there was no way I was doing Iron pipe or one of those systems that would not have been able to be customized the same as PEX and soo easy to find parts! Nice work

@crisnmaryfam7344

Жыл бұрын

People used to do this with CPVC pipe too, until it was made illegal because when one of those pipes fails it turns into a bunch of shrapnel. I suppose if you live in a non zoning /inspection area and dont mind the risk of a flying piece of plastic...

Like all the recent updates. For future installs they make a pair of pliers that are use for Pex to expand it to get on the fittings.

I have had this video dog eared for watch later for quite a while and I appreciate the links and suggestions for a better or cheaper way to set up air lines in the shop. Many many moons ago I used to Manage a shop on an Air Force installation called the Auto Hobby Shop and oiling air tools was a problem. Getting folks to remember to put a couple drops in the tool before signing the tool out was difficult and having oilers on the wall at each station was cost preventative. Also, air hoses could be signed out for any kind of work from mechanical to sand blasting and painting. The later of which you wouldn't want oil in the air hose. Our solution was Inline Oilers installed on all air tools that would require oiling and we would just have to inspect the gun and top them off when needed. I only mention this because you indicated oilers at each station. Not sure if you plan to do paint, sand blasting or Plasma cutting but I don't think you would want oilers for those items or oil in your shop hoses.

@MagaRickn

2 жыл бұрын

I remember Air Force Auto Hobby Shops! Sure miss them!

Make more videos! Great work!

I went with a galvanized pipe around the ceiling and used a simple "T" and a drop downpipe. I painted all the pipes red. I have an Ingersol Rand compressor feeding two 90 gallon tanks @150psi. as I have two inground lifts that use lots of air. 22 years later still holding air. if I ever have to do an upgrade, I'm doing it the same. Good video.

@LTVoyager

4 жыл бұрын

Galvanized is a poor choice for air. It is know to deteriorate putting metal flakes into the air system. If you read almost any technical paper on compressed air systems, galvanized pipe is generally suggested to be avoided.

Hello, Thanks for the video. How do you connect from air compressor to manifold? do you need a special fitting?

I actually called up the manufacturer like 4 years ago about using PEX. They said, "we don't recommend it, but that's what we use in our entire shop and have never had an issue."

@Pepe-dq2ib

3 жыл бұрын

i just use copper and didn't have to call the manufacturer. The copper looks really nice too.

@crapple

3 жыл бұрын

@@Pepe-dq2ib pex = $ Copper = $$$$$

@Pepe-dq2ib

3 жыл бұрын

@@crapple exaggerated, i did my entire garage to 3 hose reels and was only ~$100 with three 20' 3/4 pieces.

@fecnde

Жыл бұрын

@@Pepe-dq2ib it does. Costs an absolute fortune, but it looks nice.

@Pepe-dq2ib

Жыл бұрын

@@fecnde overexaggerated, it doesn't sound as bad when you say $100 instead of a "fortune". Not to mention my Milkwaukee M18 Propex kit cost $700. Pex-B would come out cheaper than Pex-A, but its still in the same ballpark as; copper, torch, propane, flux and solder.

Hey! could you show the connection from the compressor to the manifold? I really like your regulator on each outlet design and will probably add a water trap / filter at the compressor tank - into the manifold and add water trap / oilers at each tool station (where oil is needed). I think I will go 3/4 pex around the shop

This is so helpful! Thanks!

I am just getting into air tools and how to properly set everything up. I was looking at pex so this really helped. Only question is if I run 2 or three lines each designated for specific use ex. (1. Paint 2. Nailers 3. Acc/extra) do I need a shut off valve after the distribution to keep the lubricated line from mixing into the paint line or will not be a problem because of the pressured air flow?

Great video! Thanks for posting!

@Trialnerror

3 жыл бұрын

Thank YOU for watching!

Great video. I like the quarter-round edge on the OSB wall @ 8:19. Nice touch.

@Trialnerror

3 жыл бұрын

Good eye! and thank you!

@davekaylor458

3 жыл бұрын

@@Trialnerror I saw that too and was wondering what it was.

As scary as it seems to use something not ridgid, Pex can hold a lot of pressure. You'll cut down your throughput, though, on Pex B because of the barbed fittings. Pex A isn't as stout, but there's no reduction in flow.

I'd like to see where all the fittings go I don't want to miss up ^^:

I put in over 200' of PEX, 1" and 3/4" for dirt cheap. The PEX guys didn't make me feel fuzzy and warm. Not a problem, it works just fine at 130 P.S.I. Dirt cheap, and wicked fast.

Gotta a friend that owns a Body Shop and he ran PVC. He wasn't gonna spend a bunch of money on a expensive system because he felt the Landlord was in very bad health with cancer and he had to move soon, well that was 5 years ago and he is still painting cars every day on simple PVC piping. Thumps Up for Pex👍🏻

@chandlt

2 жыл бұрын

pex is not pvc .... it is pe x

@lajoyalobos2009

21 күн бұрын

Pex only splits if it fails but PVC explodes! PVC will work fine for years until one day it suddenly doesn't and there's an explosion with sharp PVC shrapnel. Please don't use PVC, use pex.

I’ve had pex lines in my garage for air for years I’m a plumber so it’s easy to get and I knew it could withstand the air pressure I’d run through since we air test new homes when we run pex so we can find leaks before we run water through them

@Trialnerror

3 жыл бұрын

Very good point. Thanks for sharing your expertise Chad!

Nice Superb Explained

I have a friend that owns a automotive repair shop. I helped him plumb his entire shop with PEX. Works great 👍

@dandorris8531

4 жыл бұрын

Been over a year with no problems.

@mikeholubek4419

4 жыл бұрын

@@dandorris8531 , what kind of temps? Zero - 90*F ?

@mikeholubek4419

4 жыл бұрын

@@Trialnerror what kind of temps so far? Zero - 90* F yet? Tks

@dandorris8531

4 жыл бұрын

The outside temp in the area the shop is located ranges high 20s to low 100s. The shop is insulated so nothing freezes inside. Hope that helps

Great channel !

Looks good

Cool idea, those system are f'ing crazy expensive and if you are overseas they are nowhere to be found really. Also laser level for life.

I used good old iron black pipes..in my home shop...old school..won't break.or bend..with my old school ..Saylor-beall air comprsoir..American made ..and built..in st.johns ,Michigan..good old American iron.. no China...crap.. great video..here..ty..

@johnkoury1116

11 күн бұрын

Got one of those with a Campbell 7.5 horsepower compressor . Real horsepower and not rated at high RPMs like the crappy ones...I started using black pipe as well but I believe I am going ot change to copper or pex...

@dontblameme6328

4 сағат бұрын

Pipe is best but $$$$$$$$$$

Are all the 1/2 filter regulators rated about the same as far as air volume capacity while maintaining the regulated pressure? How much drop in psi is seen when a large cfm is drawn from the system?

How straight our your lines? What is the distance between clamps?

I would gladly trade you for the actual dump that is my garage! That's rather nice, just a little messy, it's gonna be awesome.

how has the pex worked put so far? i wanted to do the same thing in my shop but when you read about using pex its a no no. Thanks

I didn't understand the need for a block centrally. I would probably put pass-thru type blocks at each station, but I guess it depends on your routing.

What size PEX did you run? Looks to be 1/2 inch

@1:20 the word you're looking for is "manifold" xD

I'm like you, although everyone said "you cant use Pex" hold my beer....been working fine at 150psi for 4 years , zero issues...

@LTVoyager

4 жыл бұрын

pex is fine as long as it isn’t exposed to UV. If any of your lines are locate where they will see sunshine, you will likely have problems in a few years. Other than that drawback, pex has a lot of advantages.

@fml5910

3 жыл бұрын

Good idea, thanks for the tip.

@denisdaigle5026

2 жыл бұрын

Hmmmm well guess wont work in a weld shop haha. Rapidair maxline it is then

@Marc-nz1dd

Жыл бұрын

You can also cover or paint the pex to protect from uv. Pex is tested to 180psi at 70 degrees. The warmer it gets the weaker. Just fyi. Pex is working great. And I saw on another vid to use lock tite instead of Teflon tape. It worked better and looks better for me anyway.

Nice job!

@Trialnerror

3 жыл бұрын

Thanks for the visit!

I'm working on setting up a small shop, love the idea of the PEX and your setup is pretty sweet... I've seen other setups where they use T's at the "bend" of the line from the ceiling to the separator or tool connection so that there's a down-spout with a ball valve for drainage. Necessary or not? Have you put one in at your bends before the water separator/regulators? Thanks.

@PeterB12345

3 жыл бұрын

Its a good idea. If you ever take any part off a compressor system you've been using, you'll likely notice condensation on it. It's in your lines too, and will eventually work its way down via gravity.

The only issue with using PEX is that it is not oil resistant. There is always a small amount of oil in compressed air, unless an expensive filter is used along with a pricey air dryer. You can use a specific grade of oil resistant poly tubing, although the stuff crawls all over the place with temperature change. That's an issue with any poly based pipe. For exposed air line, regular schedule 40 black pipe is the bomb. It will easily last 40 years, with a rudimentary air dryer and a good filter. I have installed air and compressors for 47 years, just my observations and experience.

@chemistryinstruments7156

Жыл бұрын

Plastic might shatter

@killthecardinals

Жыл бұрын

If you're going to use PEX then you must use an oil-free compressor, which is very common.

Great layout with the regulator, water trap and oil lubricator at each station, was thinking of doing this myself as I only Have a regulator/ water trap at the compressor. Can you use a oil lubricator with a sandblaster tho? Or could it contaminate the media

@Trialnerror

3 жыл бұрын

Yea, you do NOT want to get any oil in the blaster. It will clump up and turn your media into trash. I just never actually used the oiler on the outlet that I use for the blaster. Great point though and I'm sure it will help other people reading through.

Nice video

I ran a loop around my workshop in a mix of 1/2" pex and copper (depending on what I had available) and it works great. The total capacity of the loop exceeds a single run of pipe. Drops were made out of copper at the top (up and over copper bends at the top of the drop pipe to keep flow up and stop water coming down). I made a condensate coil out of scrap 1/2" copper, and drained off to the outside wall. Overall, the system didn't cost much, as I used offcuts and spare material I had from years of home improvements, but it works well.

Did you have to increase your pressure at the source to deal with pressure drops on your runs? If you measured, what kind of pressure drops did you get, roughly, in psi/length of run?

@Marc-nz1dd

Жыл бұрын

I noticed a large increase in tank capacity adding the pex line. In other words my compressor kicks on less often. And I have about 70' of 3/4 pex

I’m so confused !! Mains , loops , manifolds . . . I need “plumbing verbiage for dummy’s” . Sean from NJ. a.k.a gertrude0076 . I’m doing research for 1st time set up in my unheated ( well space heater ) garage. Been running 30 gal the last 18 yes & the tank is shot. Didn’t need all this for that compressor. Now I pitched an up right 60 gal 5 hrs 175 psi , so I will need to run piping . I gotta figure out what you guys are speaking of when using words like ¾ main , loop & manifold. Never to old to learn. 12/8/20

Regulator at each outlet and oil at the stations where those tools that require oil is fantastic! Not all tools need oil and would be a bad idea. I run a woodshop and I’m just starting to pipe in a 5HP 60 Gal that I got for pennies on the dollar at an estate sale. It has a 150 psi max rating but I’m sceptical about PEX as I live in Ontario Canada. Temps range from -45 C to +35 C. My shop is R45 insulated and heated to an ambient temp of 17 C at night and 20 C while I’m working. Although those numbers seem to be within the limitations for PEX, I’m wondering about any input from u you and other users?

@Trialnerror

3 жыл бұрын

I based my decision on the fact that all of this fell inline with the PEX specs and it's been perfect. Now, I live in NH so it doesn't get quite as cold here but we still dip below zero a solid 20 day's out of the year. I've had no issues at all. Best of luck with whatever you choose!

A year later since posting this how is the system working overall. Any issues or things you would do differently?

Not a single comment acknowledging the genius behind your "any criticisms comment B-LOW me" remark.

@Trialnerror

2 жыл бұрын

It took a true man of culture like yourself to notice. For that, I'm eternally grateful.

@K2KAYAK

2 жыл бұрын

@@Trialnerror Can’t help but subscribe to a gentleman of your caliber.

This is a great idea for personal use! But for commercial applications there could be OSHA implications. That's where PEX-AL-PEX is a great solution. That's what the overpriced RapidAir Maxline products are made of. But there are cheaper PEX-AL-PEX options out there that are safe and OSHA compliant and that you can get in 300 ft and 100 ft rolls. I thought I would mention that just in case folks looking for a commercial solution watched this video and considered PEX-A or PEX-B as an option.

@Trialnerror

3 жыл бұрын

Good call! I'm willing to risk my own safety but it's a whole other ball of wax when you do it commercially where you're risking others. Thanks for watching/commenting!

@ErikAsquith

3 жыл бұрын

Can you use the same PEX-B fittings on PEX-AL-PEX?

Recommend F1960 system better then the Crimp

How did you connect to your compressor? I'm new to this and going to be putting in a 60 gallon

@Trialnerror

3 жыл бұрын

It will most likely have a 1/2" or 3/4" NPT style connection on the compressor. All you need is that size to whatever size PEX you decide to go with. These can be found at Home Depot or Lows or Amazon. For example, if you compressor has a 3/4" and you ran 1/2" PEX you would need a 3/4 Male NPT to 1/2" PEX adapter. Hope that helps!

What fasteners did you use to screw everything into the OSB? Great video!

@Trialnerror

6 ай бұрын

Subfloor anchor screws. They bite into it really well.

Use boiling water to soften the pipe, it’ll slip on a treat.

only thing i can say is i do not know if pex will brake down in sun light . pex-al-pex would have been a better product i think.

I've considered doing this in my garage. How has the system held up? Updates please!!

@Trialnerror

3 жыл бұрын

No issues at all. I really love it and I just put a bigger compressor on it month or so ago that maintains 175 psi. Still no issues!

@SaltCityFab

3 жыл бұрын

@@Trialnerror thank you for the update. I'll be doing this in my garage soon.

Where did you get your clamps?

Mind me asking where you got that smooth metal corner bracket at 08:23 ?

@Trialnerror

Жыл бұрын

Sure, it's from Home depot but any plumbing supply store that sells pex tubing will have them.

Water separater is just fine but you don’t want oil in everything like plasma or sand blast I would install them separate nice idea though

@Trialnerror

3 жыл бұрын

Agreed but don't you think oil in the plasma air line would make a really cool flame thrower? LOL.

I used 3/4 cpvc pipe and it worked great nice video 👍

@shrconstruction

Жыл бұрын

Very bad idea....not if but when it will shatter....way to brittle.

I just got through running 3/4 pex for air in my new farm shop. Going to build a manifold with 1 inch fittings and have a 1 inch feed to the manifold from my compressor.

@Trialnerror

3 жыл бұрын

Well hell, that will do it!

I've even worked for a machine shop that used PVC for our air lines for years. Eventually we upgraded to steel, but the PVC worked fine (although it is dangerous). Pex is much softer and less likely to explode with shards of hard plastic going everywhere.

@LTVoyager

4 жыл бұрын

Yep, PVC works great right until the point where it gets brittle from age and explodes. 😁

Does no one like cherry flavored PEX? I am using orange because it has an intermediate air barrier. Since it is meant for heat the air barrier keeps air from wicking into your heat system. In theory, using orange PEX for air will keep water out or air in.

@Trialnerror

3 жыл бұрын

It also doesn't shrink/grow as much depending on temp. Should last a while longer than regular PEX. Thank you for bringing up that point sir!

The water /trap and oiler is good for tools only but the oiler part is no good for spray painting so i would separate them on another line

@mrmotofy

11 ай бұрын

Yep and it tends to bleed through many rubber air hoses...makes a mess. Learned that the hard way haha

I'll like to know the maximum PSI it can hold....

@Trialnerror

3 жыл бұрын

I'm now running it at 180 psi. Check with the spec sheet of the pex you order to see exactly what it can handle.

Nice,,,but your mains lines should be 3/4 to you separators,,, volume and pressure are totally different.

@Trialnerror

3 жыл бұрын

True. Since it's a one man garage and I knew I'd only be using one air tool at a time I figured I could get away with it. So far it's been great but yes, 3/4 would never be a bad idea for the mains. Thanks for watching and sharing your knowledge George.

@Drums4Freaks

3 жыл бұрын

@@Trialnerror for a one-man garage, would you say that 1/2" line would be enough for an impact wrench for wheel jobs or die grinders for example? I need to run about 25' rigid line to a 50' 3/8" hose reel. What to you suggest?

@Trialnerror

3 жыл бұрын

@@Drums4Freaks That's what I have and have had no air supply issues. I run my media blaster off about a 50ft length of 1/2" PEX then to 25' of 3/8 rubber and that thing takes a TON of air. No problemo

So its been about 2 years, hows the PEX workin out?

@Trialnerror

2 жыл бұрын

Mint! No problemo's.

What clamps did you use?

@Sicktrickintuner

3 жыл бұрын

They look like oatker clamps

PRETTY NEAT "" I LIKE IT !! PATRICK.P

great cheap setup. i saw the line whether 3/8 or 1/2. however if you're running air tools that using high volume such as air impact that require high volume I'm afraid it is not sufficient. it will cause great pressure drop. maybe in the future you'd consider 3/4" line minimum will cover most needs (depends on tools that you will be using). just my personal experience.

@Trialnerror

3 жыл бұрын

Fair enough. Thanks very much for watching!

It's been a year now, how's this system working for you so far?

@Trialnerror

3 жыл бұрын

Perfectly. Haven't had to touch or even think about it. I did upgrade to a much larger compressor and even higher pressure (175psi) with no issues.

People used to do this with CPVC pipe too, until it was made illegal because when one of those pipes fails it turns into a bunch of shrapnel. I suppose if you live in a non zoning /inspection area and dont mind the risk of a flying piece of plastic... Go for it. For me Ill stick to the safe stuff.

@Trialnerror

Жыл бұрын

FYI, this isn't pvc. It acts like HDPE when it lets go which is the same thing they make firework mortar tubes out of because it DOESNT explode into shrapnel.

PEX Class A is good to 160psi👍

How is this working out Now ?

@Trialnerror

Жыл бұрын

Still good as new

Those damn Nanpu separators... I give them a chance every few years hoping they improve their design since they're so cheap. Nope! Just returned the latest iteration that still leaks like a sieve, and made worse, the adjustment valve didn't actually do anything in this latest version. Yet you can't justify $2-300 in a more off-the -shelf solution. It's just an expansion chamber with a valve, I can make that...

Heat gun would work better for heating pipe

@Trialnerror

3 жыл бұрын

100% right. That's the perfect tool for this job. I'm just too much of a toll to have thought of that at the time lol.

comments or concerns... put it in the the comment secton. blow me!

Update?

@Trialnerror

2 жыл бұрын

All good! No problems.

My guy, a heat gun would have much better to use over a torch.

Like the idea of the regulator at each outlet, think I'll add that to my plan but a single filter and water trap at the source if sufficient if not arguably better. Using PEX is cheap, but it is not designed for air. Lots of people will say that they do it and it works fine, but there are also people that say they never wear a seatbelt in a car and have never had a problem. Would you put your kids in your car without a seatbelt? One would be better off buying less filters and traps and putting the money into pipe designed for air. That said, nice OCD install with the lazer. :-)

@nicholasweber21

4 жыл бұрын

I didn't know you were his safety boss. Why even post a dumb comment like that.

@lakeman2604

4 жыл бұрын

Nicholas Weber , while your comment added nothing useful to the conversation, mine provided some positive feedback as I was impressed by his very clean install and also provided a very valid argument against using PEX for air. If the poster understands the risks and chooses to use PEX, then he bears responsibility for it, but It would be tragic to see a viewer injured or killed by a pipe failure because he did not have enough information to make a better decision. Quite the opposite of ‘dumb’, but that is why I commented. Now if you choose to use PEX for air and it blows up in your face (pun intended,) at least you cannot say you didn’t know the risk. Cheers!

Iok

Your garage is cool, seen way worse than that.

Aaa

Get rid of those junk crimp rings and buy the tru compression rings, this cheapies give pex a bad name

@mrmotofy

11 ай бұрын

Crimp rings that are tested to hold up to like 1000 psi when the pex fails

People actually adjust regulators? Crank em all the way up and get all the power! Unless you're painting of course.

@Trialnerror

2 жыл бұрын

LOL, People with real compressors do. You dont want 200psi running through many tools if you want them to last more than 2 seconds. I'm running 175 now so I do need to be careful.

@djkommando

2 жыл бұрын

@@Trialnerror yeah, I only get 140 from my regulator max... 😫

Like the video and info, but am having a problem. In particular, the recommended "1/2 Barb to 1/2 NPT"....damned near impossible to get the pex onto, but with some hear, sweat, and swears, it goes. BUT neither clamps nor crimps will slide over the hose once on! I just noticed in the video, around 4:35 & 7:30, that the parts in your manifold are different from the link (short brass version, vs linked long stainless). Maybe these are a better option? www.amazon.com/dp/B08JTJRZH3/ref=sspa_dk_detail_1?pd_rd_i=B08JTJRZH3&pd_rd_w=U36vn&content-id=amzn1.sym.dd2c6db7-6626-466d-bf04-9570e69a7df0&pf_rd_p=dd2c6db7-6626-466d-bf04-9570e69a7df0&pf_rd_r=N76B0RD6D1H8719PPT3J&pd_rd_wg=QScBp&pd_rd_r=e8b43ab7-0dc5-4bdc-9ca2-2e0bbc982a20&s=industrial&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWxfdGhlbWF0aWM&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExMkZCRlFQMUgwOVU0JmVuY3J5cHRlZElkPUEwMDA3MzAxMkFRUzlBMVlPVzE2RSZlbmNyeXB0ZWRBZElkPUEwMTgwMjA1WUhTWDY2TVlQTUlJJndpZGdldE5hbWU9c3BfZGV0YWlsX3RoZW1hdGljJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ&th=1

@mrmotofy

11 ай бұрын

Use proper Pex fittings they're sized properly and tested to 800-1000psi when the pex fails before the fittings/crimps. One brand even went like 1200psi