Man this is rad! 100% my next purchase for my 68.

beauty and clean install a dream project some day ill try this but with a dual carb

@leeberry584

9 ай бұрын

It's possible you could use your dual carburator as a blow threw system but it would require more parts than just a blower. Thank you for your interest

That honestly looks like what a factory setup would have been! Very cool and great work ( also would look and work mint in a Bus )

@berrysblowers6411

4 ай бұрын

Thank you. That was the look I was going for. We now have more carburator intake options

@barryismygod

4 ай бұрын

@@berrysblowers6411 I’m curious how it would run with a appropriate CFM four barrel Or even a Holley sniper kit.

@berrysblowers6411

4 ай бұрын

I think for a 1835 the sniper would be to much but a 500 holley would most likely do good cause I have dome that with turbos

@barryismygod

4 ай бұрын

@@berrysblowers6411500 Holley would make it scoot! But holley does make an Autolite 1100 style one barrel sniper unit along with a unit similar to a Carter BBD Two Barrel. I also think a great carb to use on this would be a Weber 32/36 Progressive Two Barrel

What a beautiful engine

@leeberry584

Жыл бұрын

Thank you!!

Nicely done

@leeberry584

Жыл бұрын

Thank you!

Your kit is perfect, congratulations! I'm from brazil and I'd like to buy just the blower bracket and the outlet manifold! How can we do it?

@berrysblowers6411

6 ай бұрын

Please email or Facebook messages me please

Brilliant video. Does pulley size influance the psi the blower puts out? Ratio rockers say 1.25/1 help will with breathing more air into the motor? Electronic or vacuum boost gauge = what is the best? Distributor std bosch with petronix or after market kits is the best too use?

@berrysblowers6411

2 ай бұрын

The ignition is a 009 size with a 90 degree cap and yes smaller the pulley more the boost but I highly suggest a stock blower pulley on a 1600. And yes ratio rockers help

Did you change the jets of the original carb to work with the super charger?

@leeberry584

Жыл бұрын

I slightly ream the main jet and I opened up the pump jet all the way. Thank you for your interest

Awesome! Would you mind checking to see if a stock 73+ air cleaner would clear the deck lid?

@leeberry584

Жыл бұрын

Is yours a paper filter or the older oil bath system

@gregoryschwarz2730

Жыл бұрын

@@leeberry584 paper

@leeberry584

Жыл бұрын

@@gregoryschwarz2730 I'm not sure i have one to try but ill look in my storage building

@leeberry584

Жыл бұрын

I posted a photo of your air cleaner would fit. Its on berrys blowers Facebook page. It does not fit. Thank you for your time

@leeberry584

Жыл бұрын

I use a little paper filter

How difficult would it be to adapt the flange for a Holy or FIJet EFI system?

@berrysblowers6411

3 ай бұрын

Might not be to hard at all. Just would depend on the style of FI you have

Were can I purchase one of this kit that uses a side draft weber.

@berrysblowers6411

4 ай бұрын

Berrysblowersllc.com

Any issues with this set up with an alternator?

@berrysblowers6411

5 ай бұрын

I have not had no issues at all so far. We do have a steel intake now for the stock carburator and im Working on others at this time

What's the power gain over stock?

@leeberry584

Жыл бұрын

Ushly around 40% increase but depends on how the stock engine is built like mechanical compression and any head work. Thank you for your interest

I tried to get to berry's blowers and I could not get any were. I am a old man with a sand rail, pushing 110 hp and I think I need more. Can some body tell me how get get one of these blowers?

@leeberry584

Жыл бұрын

? How did you try to contact berrysblowers? And I am sorry I have no email or Facebook message?

Why did you make this new set up with the blower on the left?

@berrysblowers6411

5 ай бұрын

The older busses don't have room above the alternator for the carburator to clear the upper tray, so we flipped it. It was not my idea. A gentleman asked me to finish what he started and he now has the full kit and if he is happy and all workes well I will offer them. Thank you for your interest

The belt is inside out

@berrysblowers6411

11 күн бұрын

No. ?

Neat Idea, But the v belt will not last...they are not made to be ran on the back side. Really need to upgrade to a serpentine belt.

@leeberry584

11 ай бұрын

Actually, I have used v belts for a year and half one this car, and this month, we actually just pulled the engine to put a larger engine in

@georgejetson3648

5 ай бұрын

Looks like it rides on the backside only on the tensioner.