Work explained with details shown on a Leeson C42D48OB3B model, 102 VDC, 1.62 HP, n=5190
Жүктеу.....
Пікірлер: 13
@simonjones73963 жыл бұрын
Thank you, very informative
@theoverengineer
3 жыл бұрын
Glad it was helpful!
@wissambarsoum58893 ай бұрын
Can you please send me more details about those rings and how to get them, thanks
@suzesiviter60832 жыл бұрын
Great but how do you install bearings on shaft sizes around 5mm, can I just heat it up and tap it onto the shaft?
@theoverengineer
2 жыл бұрын
Tiny bearings need no heating. SKF has a bearing installation guide book, it says on page 53, Cold mounting www.skf.com/binaries/pub12/Images/0901d1968013be94-SKF-bearing-maintenance-handbook---10001_1-EN(1)_tcm_12-463040.pdf "Mechanical methods Bearings with a cylindrical bore (d = max 80 mm) Small bearings should be mounted with an appropriate bearing fitting tool, e.g. the SKF Bearing fitting tool kit († fig. 14a)."
@cadillacescalade13 жыл бұрын
The correct video is for showing us how you hv removed the bearing!!!
@The_Mimewar4 жыл бұрын
Is there any reason you didn’t heat up the bearings? Instead of POUNDING THEM ON, do it the right way, and don’t destroy your shaft.
@HairyTheCandyMan
2 жыл бұрын
Maybe his wife wouldn't let him borrow the oven 😉
@ivansentanu3498
Жыл бұрын
this is old comment and maybe too late too reply, I know by heat up bearing it can removed but some design, in my case the bearing was too close too rubber where the rubber cannot be removed. I think the goal of this video is not to remove bearing but how can we design so we can install and remove it easier.
@chrissanchez66753 жыл бұрын
Never hit the inner race of the bearing for installation, always use the outer race.
@theoverengineer
3 жыл бұрын
Right on, bro, thanks for watching!
@HairyTheCandyMan
2 жыл бұрын
I always take a chisel to the rubber sheilds and inner bearing balls. The grooves it creates make them run squeeky rough.
Пікірлер: 13
Thank you, very informative
@theoverengineer
3 жыл бұрын
Glad it was helpful!
Can you please send me more details about those rings and how to get them, thanks
Great but how do you install bearings on shaft sizes around 5mm, can I just heat it up and tap it onto the shaft?
@theoverengineer
2 жыл бұрын
Tiny bearings need no heating. SKF has a bearing installation guide book, it says on page 53, Cold mounting www.skf.com/binaries/pub12/Images/0901d1968013be94-SKF-bearing-maintenance-handbook---10001_1-EN(1)_tcm_12-463040.pdf "Mechanical methods Bearings with a cylindrical bore (d = max 80 mm) Small bearings should be mounted with an appropriate bearing fitting tool, e.g. the SKF Bearing fitting tool kit († fig. 14a)."
The correct video is for showing us how you hv removed the bearing!!!
Is there any reason you didn’t heat up the bearings? Instead of POUNDING THEM ON, do it the right way, and don’t destroy your shaft.
@HairyTheCandyMan
2 жыл бұрын
Maybe his wife wouldn't let him borrow the oven 😉
@ivansentanu3498
Жыл бұрын
this is old comment and maybe too late too reply, I know by heat up bearing it can removed but some design, in my case the bearing was too close too rubber where the rubber cannot be removed. I think the goal of this video is not to remove bearing but how can we design so we can install and remove it easier.
Never hit the inner race of the bearing for installation, always use the outer race.
@theoverengineer
3 жыл бұрын
Right on, bro, thanks for watching!
@HairyTheCandyMan
2 жыл бұрын
I always take a chisel to the rubber sheilds and inner bearing balls. The grooves it creates make them run squeeky rough.
Chutke ganduu