Nice channel, greetings from Poland

@BlueCollarBiceps

2 жыл бұрын

Thank you!! Hope all is well in Poland! 👨🏻‍🔧💪🏼

Nice vid bro ... we don't use putty on the connections much over here. Its generally silicone sealant.

@BlueCollarBiceps

4 жыл бұрын

Thanks bro. No kidding, I’ve actually heard of guys doing that over here as well, maybe something new to try!

The video you came for starts at 5:00

@BlueCollarBiceps

3 жыл бұрын

Sorry about that! Haha new KZreadr problems 😂

8:17 food for thought with some wide spread faucet's you can use a 12in crescent wrench for the under nut room permitting. With ones that don't have the water ports sticking out a tub socks will also do the trick. Also might want to install the faucet before setting it on the top other then that sold install.

@BlueCollarBiceps

3 жыл бұрын

Thank you! I wanna say doing this one I was a little out of order on my filming but typically do install the faucet first which is what I ended up doing as you could see it the video after. I appreciate the feedback and input!!

Great job 👍

@BlueCollarBiceps

3 жыл бұрын

Thanks!!

I’m loving all the edits! Great content and I learned so much!

@BlueCollarBiceps

4 жыл бұрын

Thank you. I appreciate the kind words and positive feedback!

Put in a Moen Genta 2 handle in the bathroom and both faucets leak leak a little at their bases when turned on. No water underneath. Did exactly as you did, decent roll of pipe dope, snugged up the faucets underneath but not really cranking on them. Retightened them, leak is worse. Going to pull them both off, redo the pipe dope again. Is it normal for the faucet valves to leak in operation? I gather it is since they require dope or o-rings. Kind of pissed that for the prices they want for fixtures, they can't throw in some 10 cent o-rings.

@BlueCollarBiceps

4 жыл бұрын

They definitely should not leak during operation! You say you used pipe dope? The only sealing you should have to do is with plumbers putty on the underside, maybe that’s the issue possibly? Let me know if you figure it out!

@Bryanvcarbino

3 жыл бұрын

If you use plumbers putty and put a complete roll around it it should never leak. Plumbers putty has been a round forever and for good reason. I would never use anything else where plumbers putty will work

Love the Home Depot edit 😂. Another good video man!

@BlueCollarBiceps

4 жыл бұрын

HVAC Tool Review Haha thanks man! Appreciate the support 👊🏼

I only use 1 step clear glue on small diameter drains

@BlueCollarBiceps

3 жыл бұрын

Any specific reason? It’s new to me man so I’m genuinely just curious.

@jstu45

3 жыл бұрын

@@BlueCollarBiceps I think clear glue is weak compared to blue glue

@BlueCollarBiceps

3 жыл бұрын

Okay makes sense. I’ll have to give the blue glue a try, I’ve only used clear. Thanks for watching!

I just installed exact same faucet and followed instructions to a tee... all I am getting is a light drizzle, not a full flow like your shows... water supply is strong, I tested those lines and they are clear and working great. I tried taking out tiny filter all together, made no difference.. any ideas what the problem might be?

@BlueCollarBiceps

4 жыл бұрын

Alicia Waldschmidt everything is completely on at the water supply shutoff valves?

@Bryanvcarbino

3 жыл бұрын

Any luck with that vanity faucet. Mines the same. All kinds of pressure feeding the sink but my identical faucet trickles water. I dropped the plastic cover under the spout and removed the two Allen screws. Going to get tool and remove the aerator. Is there some flow restriction on these faucets. This is my master bath vanity faucet

I have the same faucet and the water pressure is super low. It was fine before i installed it. Do I need to remove the aerator?

@BlueCollarBiceps

3 жыл бұрын

Yes definitely take that off and see if there is any sediment caught inside and if so just rinse it out

How did you connect the pop up?

@BlueCollarBiceps

3 жыл бұрын

This one feeds up through the neck of the spout and hooks up that way. It should be right in the manual as well!

How you like those tundras?

@qomco

3 жыл бұрын

Also, nice work. Those details make the difference

@BlueCollarBiceps

3 жыл бұрын

Thanks man!! I love my Tundra it’s an 08 and it’s treated me well. I don’t see myself getting rid of it anytime soon!