Basic STANDING SEAM Metal Roof | How To install.
In this video we’re doing a basic standing seam metal roof, I hope y’all can learn something, and just be aware this might not be the exact type of trim and panels that you have access to in your area, but some of the basic principals could still apply. Also normally you would probably have an “A” Frame roof your working on, not a Lean-to like this one, in that case line up your Rake, (Gable, or Corner) trims up at the peak, and make all the points meet. On another note, Some metal roofing shops can make custom trim so take advantage of that,
Here are some of the tools we like to use, these can be found on amazon via the following links;
Left off-set snips: amzn.to/3uJD5kF
Right off-set snips: amzn.to/3NcSpMS
Edge roller: amzn.to/3GtsBs6
The caulk we Love to use (super strong!!) amzn.to/3GzyF2r
18” hand break: amzn.to/3GrB0wn
You can also get this in a 24” length for Hemming the bottoms of valley angles on standing seam.
Our favorite gloves: amzn.to/3T5jp4R
Our favorite roofing Shoes: amzn.to/482YyU4
(AKA) Hiking Boots)
Power Metal Shear: amzn.to/46IIh5B
Impact driver: amzn.to/3t26iqn
Hand Break 6”: amzn.to/3R6uiRb
Hand Notcher to notch the bottom edges of your standing seam panel for Hemming the bottoms if they don’t come pre-notched from the manufacturer: amzn.to/3Tbl88K
Rubber Mallet: amzn.to/46HAk0A
I am an Amazon associate, and may earn a commission if you purchase any of the products using the links I have listed in the description.
Пікірлер: 15
Thanks guys, It's nice to find DIY videos made as well as yours. I can't think of anything that would make it better. Thanks again.
Nice job. Great info. Thanks!
I liked your presentation. I just need more tools 🥰🥰
@plankroofing
6 ай бұрын
Links in the description for some of the tools we use.
good work
very professional. Nice work.
Nice work guys, can you make a door to close the end on the overlapping panel at the drip edge
@plankroofing
6 ай бұрын
We always bend a piece around to close the end of the rib. whether it’s a factory pre-cut that you just bend around, Or using a tin snips to make a “door” To cover the end of the rib.
@johnbruzzi4381
6 ай бұрын
@@plankroofing I didn't see it in this video
@plankroofing
6 ай бұрын
@@johnbruzzi4381 it’s at the 6:00 minute mark. Between 6 and 6:10 All he did was bend the tab around to close the end of the rib. Because it came pre notched from the manufacturer. If it’s not already notched you have to cut out a tab with your Tin snips to make a “door” I wish I had a video demonstrating this but I don’t.
@johnbruzzi4381
6 ай бұрын
@@plankroofing no I know how to do just didn't catch it in the video, my bad
Hey quick question what’s the rake trim name
@plankroofing
Күн бұрын
@@samvarios610 we just called it standing seam rake. This is about the only company I know of that makes them this way. Royal oak metal sales in Michigan. But there are some metal suppliers who will make something like this custom.
where do i buy the bending machine
@plankroofing
6 ай бұрын
Which one? Are you taking about the edge roller for bending up the finisher piece? Or the 18” break for hemming the bottoms? I put links to both of them in the description. I believe we got the edge roller off of Amazon.