I work at a high school technical center. Your information is perfect for the kids to comprehend. Also, just short enough to keep their attention. You make everything very easy to understand. I’m in my mid 50’s and grew up with all of what you are teaching. I especially like that everything you teach is universal. I’m a Buick guy and I have thought back for several years now.. “ hmm what did Tony say”.. thanks for your time man.

@Schlipperschlopper

3 ай бұрын

Ever thought about missing oil thrower paddles on aftermarket conrods? Original GM Small Block rods have so called Splashers that throw oil on the cam lobes, most aftermarket rods dont have these oil throwers

As the elder Boomers are aging out and the youngsters are moving in you should do videos like this. How to READ stuff, bearings, gears, etc... and those of us still invested in HotRodding love the content as well.

@noneed4me2n7

Жыл бұрын

His stuff is so easy to watch. As someone who was out of the hobby for a time for reasons, it’s like the easiest to understand refresher courses I’ve ever had. He keeps his explanations simple and backs up most of what he shows with physical examples of the how and why.

@richardprice5978

Жыл бұрын

426 hemi/440RB's are actually off set by about 1/16' back ( on top of original usage of a crowning on the lifter's ) on the cam vs lifter's i know because i measured it for my roller viper-cam style im using

More than 40 years ago I bought a 68 Chevy truck from a garage that acquired it with a mechanics lean. What happened was they put in a used engine supplied by the owner and it ran like crap. They told him the cam was bad and what it would cost to replace it. The owner didn't want to put that kind of money into a 15 year old truck but also refused to pay for the work already done. I bought it by paying off the amount owed thinking I was going to need to replace the engine. My father in law owned a garage. When we checked about 4 lifters had no tension against the rocker, "very early Chevy 350" But my father in law noticed that when the engine turned over the push rod moved as much as ones that seemed normal almost like the pushrods were too short.. Pulled and measured, all the same length, started pulling lifters. All were fine except the 4 in question had wore clear through to the hydraulic center. My father in law ordered another set of lifters. We dropped them in adjusted the lifters and the engine ran fine. No smoke no noise. I ran it for another 12 years and sold it for a lot more than it cost me to buy it.

@daveo532

Жыл бұрын

Don't care if you got another 12 years out of it. You do not put new lifters on a used cam. Period.

@johnkendall6962

Жыл бұрын

@@daveo532 New lifters are put on used cams all the time. All you do is act like a new cam break in.. Run the engine at about 2500 for half an hour an very the speed up or down 200 rpm. If there would have been a problem it would have showed up. It was not a high performance engine so the valve springs tension was not very high and we readjusted the valves after break in. We put other used cams in without problems. I put a used cam with higher lift in my 289 mustang motor out of a 351. There wasn't any problem. Just had to change the firing order.

@reallifehardtruth4465

Жыл бұрын

Change lifters all the time. No biggie.

@Jonhobbs64

Жыл бұрын

@@daveo532 I think you got it backwards buddy you never put used lifters on a new cam..

I thought I knew a fair bit about cams and lifters, and their operational dynamics, but man oh man, there's a lot of good info here that I'd never even considered. Thanks for the great lecture, Tony, you are a true master.

Good Stuff! I've been building motors for over 30+ Years and actually learned something I didn't know...The reversed tapers on a properly ground "A series" MOPAR motor. Myself, I build GM motors these days, specifically Z/28 302/LT-1 motors. The last LT-1 I built I wanted it to "run a little better" than OEM, called up Bullet Cams and ordered a couple of UltraDyne solid flat tappet lobes I always liked. The OEM GM solid lifter came in 2 types, the "piddle valve" and "edge orifice" type that cuts top end oiling by about 15-20%...Fun Fact the majority of late 60's solid lifter HP motors had the "585" series edge orifice in them. I was running roller rockers and didn't need the full oiling. The OEM GM lifters have a stellite hard face on them, they are far better than anything else ouside of a tool steel lifter and the best for long term street reliability... the last time they were sold through Gm they ran about $32 each,this was in the late 1980's!!! Not cheap. I had a 302 Z/28 motor that had some in it with less than 5,000 miles on them. I sent them off to a service that would re-radiuus the lifters...Guy said I might be better off going with a 100inch radius rather than the 120inch that was OEM specs....I called Bullet Cams and asked them....Yes! They said that would be better, so today after 20,000 miles, the 70 LT-1 just ran 12.98@109MPH through the mufflers and on street tires....TKO600 5 speed with steep 1st gear helps get the job done. Not bad for an old "dinosaur" without EFI or computers....Does have a factory breakerless ignition, and ported "186" heads, factory intake and 0.030 overbore....better rods and 10.5:1 lower compression.

@jeffrykopis5468

Жыл бұрын

Very interesting. I saw a video tour of a small cam regrinder in Tacoma a few years ago. They said they not only regrind stock cams, but reface stock lifters as well! They said factory lifters, reground, are much more reliable than the offshore crap sold nowdays! I'd never heard of reground LIFTERS before then, or since...until now.

I'm 65 almost 6. I used to wrench on my vehicles out in the backyard all the time back in the 70's. Mom told me once she asked dad to go out and help me (WW2 military mechanic) she said that's how he learned. 40 something years later, thanks uncle Tony ! Very informative.

I raced 340 Super Stock in the 70's. I knew about the cam taper but not about lobes being ground to cancel out the thrust. Thanks for teaching a old racer something new!😀

Absolutely brilliant video Tony!! This is why I love you and your content so much dude, you don't just talk about things, you KNOW about things. The taper being a part of harmonising the cam shaft when off throttle... Genius! Its stuff like this that I just love. Superb stuff, thank you very much for all your work dude!

Hit the nail on the head again Tony! Love how you break down these tiny details and make the knowledge accessible. Entertaining and informative. Thank you!

My uncle's engine of choice in his race boat was Australian Chrysler hemi 6, but he kept breaking oil pump drives due to non retained cam in early version. Fortunately he worked in the local Chrysler factory, so his boat became a R & D rig.

I love this nerdy stuff! I also love learning the little intricate stuff like the taper is actually ground on opposite sides of the lobes to help with cam endplay! That's awesome! They really thought of everything when building these engines back in the day.

I learned my lesson. I grew up in the 70s in Detroit. I grew up seeing all of the best muscle cars. Fast forward 40+ years. I bought a 1978 Trans Am. I didn't do my research. I was just a kid in the 70s. I used oil without zinc. I blazed through my Cam within two summers of driving. I had my engine rebuilt completely and went back with a somewhat radical Cam and headers. I now run the correct oil w/zinc and I am heading into my 3rd year since rebuilding the engine. And.....I continue to watch UTG to learn more and more.

if you're going to do this then you may as well do rear end ring gear wear patterns! anybody who's built a rear-end knows that they show you 50 different wear patterns when you apply that yellow paint some that are acceptable some that aren't but I'd like to get your input on this and take a look at a ring gear that has a hundred plus thousand miles on it!

Im 75 and just learned something from this vid. Im peggys hubby, and build hot rod engines, and have learned so much from you , andy, and david vizard ! Keep doing these vids. !

I recently pulled the cam out of a AMC 360 after a 25 MINUTE CAM BREAK IN . 15 nos flat tappet lifters and 1 China lifter . The China lifter did not servive. I spent a bit of time looking at the cam ware patterns and could definitely see all of the wear patterns that you talked about on this type of cam style. Your vids are in sink with my build progress. New cam and lifters on the way. Johnson hylift lifters, made in michigan coming with the new cam . I'm that nerd

@burgegerm7878

Жыл бұрын

I looked at the website, and it seems they only make roller lifters. I wonder why people can't make solid lifters anymore. It seems it would be simple to take a bar of the right material, machine it to size and machine (or grind?) a taper on the face.

Excellent video Tony. This is stuff I never even thought about. You are brilliant and you know so much. Please, keep sharing, I love it.

Thanks Tony for the super informative cam tutorial, I learned a tremendous amount. Pictures with words is golden! Well you are at 100F, we've got 50F in NE PA, I'd take my temps any day! Have a good one Tony!

47 years old and have always been an old car/pickup guy. I’ve always been intimidated by this stuff. You make it easy and enjoyable to learn.

This is absoposolutely the best instructional video! thank you Uncle Tony!

I learned something new! Makes me really lean toward roller next engine I put together. I loved the little truth bomb about the zinc pennies as many people still think they are a copper alloy as they were before 1982. Great video again!

Just love this kind of information! Thanks Tony! Reminds me of your air scoop video. Fantastically interesting to me and others , I’m sure!

There's so many details that seem trivial but are really foundational to understanding what we're trying to do with our cars. You keep teaching me stuff I didn't know I needed to know

This is my favorite type of UTG content, thanks for sharing.

I love this stuff. Uncle Tony, if you'd do an automatic transmission disassembly while naming each parts function I would be tickled. Then reassemble part by part. If that's too much to ask, then how about doing a shift kit install whilst explaining how it improves shift performance and why. There's plenty of videos on that subject but I retain the info better when I hear it from you... Thanks, Little Mike

These videos do help demystify the issues with camshafts that I keep reading and hearing about. I think they went back to non-tapered camshafts for some newer USA overhead cam engines. I have a 2007 2.0L Ford Focus duratec, and it has flat tappets. I am pretty sure I read that they are offset to keep them rotating, but do not recall 100%. By the way, as far as modern USA engines go, I think that the 3.0l Ford duratec (like in the 1996 Taurus) and the 2.0L Ford Duratec (Like in the USA Focus) are pretty good. I have about 295 thousand miles on my 2007 Focus with manual transmission. Though I did remove the intake tumble flaps.

That was a very cool video, Uncle Tony.

Uncle Tony: “heavy duty gear head nerd stuff” Me: leans in closer and turns up the volume

That was cool! Most tech talk bores me to no end but this one kept me locked in until the end.

I love this content. I could listen to these bits of knowledge for hours.

UTG, I never stop learning things from you. Great channel!

This information is quite impressive, definitely something I didn't know, excellent video, thanks, all the best to you and your loved ones

Every gear head should know and understand this great video!

Thanks for the informative lesson! Please consider doing more on cams, like lift and duration and what that boils down to in practice, with different rocker ratios. 👍👍👍

Great video, you have a knack, thanks for making it.

Very educational, thank you for explaining it so well

Thanks Tony, that was very helpful. The other topic was valve guide seal. Teflon its what my brother used back in 82' on 77' 351mod. 400 heads. Economy performance cam. holly 650 dbl pumper. I saw your vid where you covered it. A company makes them now. It prevent the morning puff of smoke from the drain down on an older motor.

More great information thanks Tony

I’m currently installing a CompCams “Thumper cam” in my Chevy 350, a little nervous about break in but really excited to see the results! I got 6qts of CompCams break in oil and then for the oil to run after that I got Lucas “hot rod” oil that has the added zinc for old school engines

@thepoopsoup

Жыл бұрын

Use the silver never sieze on cam and lifters for break in do not get any on the sides of your lifters they need to rotate 15 min 3000 rpm change oil.

@MrTheHillfolk

Жыл бұрын

Don't be timid on the startup. Once it fires up and you don't see gushing fluids in 10 seconds ,bring the revs up to 2000-2500 to get those lifters spinning and proceed.

Very informative video. A video like this showing how to read crank & rod bearings would be great too, if you ever get a chance.

Nice video UTG! Great information! 🤩🤩🤩🤩

ANOTHER GREAT VIDEO TONY. THUMBS 👍! I Learned something new. Thanks for sharing .👍

Hey Tony, Tim here, altho i know about the wear patterns, and lifter spinning, i LOVE gearhead nerd stuff!!!!!...i am a gearhead nerd!!!!!...ur vid was spot on, concise, and usefull for all them youngbloods......enjoyed it......u can make a gearhead nerd vid EVERYDAY as far as i'm concerned...hahaha.....good stuff...PEACE to you sir!!

Outstanding video !

Super informative, thank you for the great content

great video UT!

Thanks. Tony again for sharing your wealth of knowledge. Regards from Australia 🇦🇺

Great show uncle!

Good info. I always enjoy your tech vids, because of how you explain stuff. I have such a hard time explaining these to "normal" people, and end up way over their head lol

I was asking for this very thing, thanks Tony!

stunning video mate...

Factory cams for thrust plate engines used to be configured so that one lifter would usually be forward, the next in the valve opening sequence, intake or exhaust, would be the opposite, back, then front, back etc.

Good stuff 👍 something on oil control inside the engine, pros & cons windage trays etc would be good !

Good video, nice work. Thanks.

More nerd stuff! Thank you sir! This is exactly what ppl like i need. Some tuner guy told me my cam was shot but could not explain me why he came to that. I now know he just wanted to sell me a new one.

Another excellent vid ! Learned a lot ! thanks !

This is about the best video on how to be a ninja I’ve ever seen no one has covered the topic of lectures wear patterns. In 16 minutes one can teach shop class professionally outstanding work Tony

Thank you for all the fantastic info I'm fixing to pull out three or four old cams and check them out that wiped a few lobes back in the late '90s when Mobil 1 oil was all the rage and it had no zinc in it even the Chevrolet instruction manual that came with the camshafts said do not use anything besides natural crude based oil and specifically warned against using synthetic motor oil with their camshafts they were ground by crane this is for big block Chevy (l88 cam in 454 , 781 heads, 11:1 etc) once again thanks for the great info!

Than you Tony, just the sort of content I love from you. Now I’m going to obsess about the engineering choices of the manufacturers, thrust plate or not…

Great video enjoyed every minute thanks.

Thank's Tony, answered questions I didn't know to ask...

Well done uncle Tony loved it! Tell uncle Kathy and the guys at the shop I said hi:) have a good day man:)

Thanks Tony....that was very interesting, I love all the nerdy stuff I never learned.

UT, another excellent educational video. 😎👍

Awsome tech tips thankscfor sharing

Personally, this is the type of stuff I watch your channel for. I like the tech videos best.

LOVE the nerd stuff Tony! Keep ‘em coming!

Fascinating! Thanks.

Wow! I'm only 3:00 into the video and have already learned some great and interesting info! Very good content thank you so much

I learned quite a bit. Thanks U. Tony

Love it Tony give us more !

Gotta luv the gearhead monk....luv the topic I always learn something new with UT....never a dull video or topic with this guy. The cams survived the video...lol.

THANK YOU I NEEDED THIS INFORMATION.

Awesome video, loved it.

Tony....LOVE the content!

Thanks Tony! I learned a lot.

Uncle Tony I'm glad you made this video because I do use cams in my engines you know that's why I take a micrometer with me to check my lobes to see if and and check and make sure that this camera is still functioning and can this can be repaired or not thank you and keep up the good work holla if you hear me

Very good video thank you!

Thanks so much Tony! I never knew all that..

I learned something new! Thanks Tony. I always wondered what made the lifters spin.

Great content! Would you please explain the relationship between decelaration of the engine and cam pushed at front? Thanks!

Interesting. I knew about the taper on the cam and of course why it's there but never really paid attention to the difference between how it's done on different blocks or manufactures.

I love failure analysis, that's the best stuff ever.

In 15 minutes I learned more about the cam and lifter interactions than watching all other videos including tv videos. 👍🏼👍🏼👍🏼

Ohhh Tony! You came sooooo close to having the world's first Stunt Cam!

One additional source of lube is the rod side clearance .Always check this when building your engine and err on the larger size . I"ve run up to .030 side clearance on a mostly street build with less than 450 hp. I also use a lifter galley shield that has 3 functions . 1- keeps hot oil off the bottom of the intake, 2- helps keep oil around the lifters and 3- helps retain the lifter incase of a push rod failure. Also ,when building the engine always check the lifter bore with a new lifter before you have any machine work done . Make sure it spins freely ! this way you can tell your machine shop weather to hone the lifter bores or not { or just give them the lifters }. One last thing , before assembly , slide the new cam in and make sure it goes all the way in ! Sometimes blocks have a core shift from the factory .I found this out on a 1968 440 block. I took it to a shop and they confirmed it and used a cam bearing cutter to take a couple of thousandths off. Hope this helps a few people.

I learned something tonight, thank you.

Thanks tony! 👍

This is a _great_ video. Makes me want to go out and collect all the engine tools I've sold throught the years, sneak an engine stand up into my second-floor apartment along with torque wrenches, a degree wheel, a flow bench and an engine dyno. Start tomorrow.

HOWdy U-T-G, Thanks for the INFORMATION COOP ...

Thank you!

Great video

I asked and you provided. Thanks UTG

Thank you so much

Great Video

Love it!

Another great classic engine educational video about camshafts and flat tappet lifters. Again, you really need to investigate teaching auto shop at your local community college. 👍

no this wasn’t too much info. thanks for this! 👍🇨🇦

The part about the Helical gear leading/lagging & pushing/pulling was an "Ah-Hah!" moment - Thanks Uncle Tony!

Great mechanic ..good video

Interesting - thanks. CHEERS from AUSTRALIA.