Great video explaining the process and showing the results, absolutely a fantastic job. Thank you for sharing your knowledge

You're got a great gift in your painting skills... job looks fantastic! Thanks for sharing your knowledge and experience!

@MrWatchOutNow

3 жыл бұрын

Thank you so much 😊

Nice video. You do a good job explaining and seem comfortable in front of the camera. Keep up the great work!

@MrWatchOutNow

2 жыл бұрын

Thank you 😁

I see you. Thanks for the great review and demo! Let's get you in that club!

@MrWatchOutNow

2 жыл бұрын

Thank you, appreciate you 😁

Thanks, As a DIYer I found your video very informative. I shot a lot of hammertone and wrinkle finish with high end siphon guns in the day, but know little about HVLP sprayers. This sprayer looks good for the homeowner DIYer like me.

@MrWatchOutNow

Жыл бұрын

Glad you found it helpful 😁

I actually was standing in Harbor Freight last night, looking for videos on the AV-100. I watched the application speed in a video or 2 for the AV-100, and, before I say this, let me say I have some experience applying coatings and finishes, and spraying them as well. Not an expert, but I get good results. The AV-100 looked painfully slow to me. I caught your first video on the AV-200 while in the store, and that clinched it for me. I loaded up an AV-200 in the cart and made my way to the register. For $60 more than the AV-100, I know I will use this machine on more than one project, and I watched this video the day after I bought the machine, and I am even more confident I made the right decision. Thanks for the videos!

@MrWatchOutNow

Жыл бұрын

I’m happy I could help 😁

Thanks for a great video. I am just a hobbyist and DIY-er and I just want a decent spray system that doesn't require me to go get a huge air compressor, and this sounds like the kit for me. Thanks again, and subbed.

@MrWatchOutNow

2 жыл бұрын

Glad I could help 😁

Thanks for sharing your awesome information

@MrWatchOutNow

2 жыл бұрын

You’re welcome 😁

Thanks for sharing you information

Bruh, that is good work. As a professional I wouldn’t be able to tell the difference of what machine you used looking at the end product.

@MrWatchOutNow

3 жыл бұрын

I appreciate that 😁

I bought that machine last week. It’s a good machine it sprayed spar urethane straight out of the can. Flawless finish try it. Good review perro

@MrWatchOutNow

Жыл бұрын

😁 thank you

Looking like I m going to try one of these. Have some fence to stain and exterior trim to paint. Wife probably doesn’t want me spraying inside. 🙄 Excellent finish.

@MrWatchOutNow

2 жыл бұрын

Lol, have at it. As for the trim, if it’s not much that needs to be done I would recommend that you roll it.

Hey vic you ain't lying about av200 I've got it an it's a damn amazingly good unit it runs like a demon sprays kiltz like it's water out the garden hose an I'm telling not like you don't know but it's a hell of a good sprayer easy to use easy to lay down paint hell for one fifty an 8 foot by 10 foot in under five mins you can't beat the price or the quality of this unit I love it an from day one it more than paid for it's self who needs a expensive high end sprayer when this unit sprays just as good to hell with leaving it in my truck though for a back up it stays in mine as my main unit

@MrWatchOutNow

2 жыл бұрын

😁 now that’s what’s up

Thanks for the vids Victor. You convinced me to go out buy the Avanti. I've used an airless for house and finish painting, but this is my first HVLP. I'm going to use mine primarily for furniture refinishing and light stuff using latex mostly. I know the thinning thing, but tip size is my question. The 1mm or 3mm for thinned latex on small work?

@MrWatchOutNow

2 жыл бұрын

Use the 1mm, the 3mm will spray too much and won’t have a good finish.

You are a natural speaker/teacher. Make more videos. Reduce the number of missteps (the ones you point out later) by preparing a list of topics in order that you want to discuss then do a clip for each and edit them together. It doesn't have to be all one take.

@MrWatchOutNow

6 ай бұрын

I appreciate the feedback 😁

Thank you brother great video. I've been changing all the molding in my house to Craftsman style I had an airless sprayer, but I just ran to Harbor Freight and got this one. Any experience with spraying Sherwin-Williams Emerald it's a water based urethane. Thanks again keep the peace

@MrWatchOutNow

Жыл бұрын

Not a fan, it’s too thick for the machine. You can thin it but I feel you’d like it more if you didn’t.

Really great videos.. Im getting into diy refinishing … have you had a chance to shoot urethane like “ emerald “ on any trim or cabinets ? Thanks !

@MrWatchOutNow

2 жыл бұрын

Yes, Use the oil base version and you’ll get some beautiful results

Hey brother, great video! Suggestion for using your phone to film: put it in a plastic ziploc bag. You don't necessarily need sound, because you can overdub the video afterwards, in post production. You get the video you want, but don't sacrifice the phone. Cheers!

@MrWatchOutNow

4 ай бұрын

Thank you 😊

Great vid and would love a how to on the counter top.

@MrWatchOutNow

2 жыл бұрын

@Marcus Smith here you go and thanks for being patient. kzread.info/dash/bejne/Z4FhqNevmqbNYag.html If I need to do a better video then just let me know.

Subscribed brother. Good luck with that revenue lol

@MrWatchOutNow

2 жыл бұрын

Lol thank you I’m gonna need it

"Exact same finish quality", sold me. Getting one tomorrow.

@MrWatchOutNow

2 жыл бұрын

Heyyyy 😁, are you a refinisher too?

@shanewatkins5636

2 жыл бұрын

@@MrWatchOutNow just doing my own cabinets. I have experience with airless. Never used hvlp.

@MrWatchOutNow

2 жыл бұрын

@@shanewatkins5636 just remember to filter the paint if you’re going with water based

@shanewatkins5636

2 жыл бұрын

@@MrWatchOutNow will do. Thanks for the advice and informative videos.

Was it a glass or cast tub? Product? Was the counter Formica type? Product? Great videos ...thank you.

@MrWatchOutNow

2 жыл бұрын

Fiberglass tub, Midwest Chemicals in Orlando Florida, laminate/Formica counter, Midwest Chemicals, everything was Midwest Chemicals. Tub- 2 part epoxy primer then 2 part high solid enamel. Counter- 2 part epoxy primer, multi spec then 2 part polyurethane clear.

Where do you get the multispec? ? Didn't know they still made it ! Used to paint Vans Stores with multispec oil !

@MrWatchOutNow

2 жыл бұрын

Midwest Chemical in Orlando Florida. Just before shooting the paint I show the jugs with the information. They have everything you’ll need and ship all over the US

Hey vic. Thanks again for the helpful tips. I hope harbor freight paid you for using your vids 😅. Hey quick question though. I just ordered my paints for refinishing my kitchen cabinets. It says they recommend. 08 tip for spraying. Do u think the avanti av200 will work? Can u change tips if needed? Thanks man!

@MrWatchOutNow

2 жыл бұрын

Mannn no they don’t pay me 😭. The Avanti will work but you can’t swap tips, it comes with 2 different types of guns one for thick material that I don’t use and the fine finish tip. The tip they may be referring to is most likely for an airless sprayer. I hope I was able to help 😁

@SaintMFLow1

2 жыл бұрын

@@MrWatchOutNow Thanks Boss! Finished the cabinets! they cam out decent for the first try too. also i am taking your advice and offering to do doors just to get some more experience under my belt and see if i can make $100/HR 😄. tHANKS Again chief

I’m looking to get into tub refinishing business. Do you think this is a decent sprayer to get started with

@MrWatchOutNow

8 ай бұрын

Get the 3 or 5 stage turbine instead. Then you can purchase any spray gun to use with it.

Nice work ! Watch out now!

@MrWatchOutNow

2 жыл бұрын

😁thank you

Lmao 😂 love the video !!! KZread wildin!!!

@MrWatchOutNow

3 жыл бұрын

Lol thanks

Do you thin latex paint before using? Thanks for the vid!

@MrWatchOutNow

2 жыл бұрын

Yes otherwise it’s way to thick

@EricInTampaAcoustic

2 жыл бұрын

What’s your thinning process/ ratio, etc? Thanks for the great video

@MrWatchOutNow

2 жыл бұрын

@@EricInTampaAcoustic I just add a little water or Floetrol at a time till I get the consistency I like

Also where you get the 2 part epoxies ?

@MrWatchOutNow

2 жыл бұрын

Midwest Chemicals

Hi. I want to do my countertops with multispec. Did you have to thin it out when spraying with the big tip gun?

@MrWatchOutNow

5 ай бұрын

If it’s a fresh batch no, just stir it well. If it’s a bit clumpy just add like an ounce of water, nothing crazy or it will just come flying out.

@luiscornejo8957

5 ай бұрын

@@MrWatchOutNow thank you for your reply also what would you use to thin down the 2 part epoxy primer with the small tip gun and would you thin down the clear coat?

@MrWatchOutNow

5 ай бұрын

This machine is strong enough to not need a thinner, but if you do then use xylene. For the clear it depends on the base(oil, water, poly)

You also might try putting some clear tape on your phone camera ! Might help with your over spray !

@MrWatchOutNow

2 жыл бұрын

I think I’ll just buy a waterproof case so I can shoot while spraying

Looking into getting 1. How many jobs u done with it b4 u had problems with sprayer?

@MrWatchOutNow

2 жыл бұрын

Still haven’t had a problem. The gun with the big tip has a slow trigger response to close now, but that’s my fault because I forgot to clean it for almost 4 days. But I can take it apart to lubricate the enclosed area I just haven’t yet because I really only use the fine finish tip

@jamesgarces9652

2 жыл бұрын

Koo. People told me not to buy the old Krause spray machine b4 discontinued cuz it was cheap and not made for heavy use. But it's been 13 months & it still going hard. They good for apartments gigs. Light easy clean up and jus get the insurance at freight and easy switch out when needed.

Was the tub refinishing, Ekopel by chance, and what if anything to thin with ?

@MrWatchOutNow

5 ай бұрын

It was Midwest chemical and thinned with laquear thinner

@JohnMiller-lq2lg

5 ай бұрын

@@MrWatchOutNow Thank you

Mine just came out chunky . What do I do. Its for a wall. I did the whole thing with water. And now I have drips everywhere

@MrWatchOutNow

Жыл бұрын

First thing you could’ve done to save it was roll over it. I wouldn’t recommend using this machine for a whole wall, just small projects. If you’re just doing a wall or 2 I would strongly recommend using a roller.

What paint did you use for Bathtubs???

@MrWatchOutNow

5 ай бұрын

Midwest chemicals

lol I am here because harbor freight

KZread pay the man. KZread y'all are a bunch of crooks aren't ya‽

that's a shitload of orange peel

@MrWatchOutNow

3 ай бұрын

Good thing I’m not spraying cars

Get to the point dude

@MrWatchOutNow

4 ай бұрын

I got to the point about 3 years ago 🤷‍♂️ 🤣

Can you buy replacement tips or gun for the sprayer

@MrWatchOutNow

Жыл бұрын

I don’t believe you can. But harbor freight sells another hvlp unit that you can use any gun on, the Avanti 3 stage sprayer