Audi, Ford, Mazda, Skoda, Volvo, VW: Hvordan bytte hjullager foran, "Generasjon-2"
Filmen viser demontering og monterings verktøyet av hjullager "generasjon 2" på to forskjellige måter:
1) Med bruk av spindelakselen som er i verktøysettet
2) Med bruk av verkstedpresse
Vanskelighetsgrad: Middels.
Tidsforbruk: Ca. 1,5 timer pr. side.
Verktøy: Hjullageravdrager-/ monteringsverktøy, Separator, Skrallesett, 7 mm unbrakobits, Torx T25, Muttertrekker, Stor hammer, Ca. 1,5 meter jernrør/spett, Latmannsarm, Momentnøkkel, Skrustikke, Dypfryser (til å kjøle ned hjullageret).
"Generasjon-2" hjullager* benyttes på følgende bilmodeller:
Audi: A1, A2
Ford: Focus II, Mondeo IV, C-Max, S-Max, Galaxy
Mazda: 3
Skoda: Fabia, Roomster
Volvo: C30, S40, V50, V60, S60 II, XC60, XC70 II, C70, V70 III, S80 II
VW: Lupo, Polo, Transporter, Multivan, Touareg
(*fra 62 mm til 85 mm i diameter)
På vår nettside finner du et stort utvalg av bildeler som du kan være interessert i www.bildeler.no
Har du noen spørsmål eller noen videoer du ønsker å se? Skriv til oss i kommentarfeltet og gi oss en tilbakemelding.
🔔 Abonner på Bildeler.no for å ikke gå glipp av nye videoer til hvordan bytte reservedeler på bilen ➜ Her / @bildelerno1
Fant du denne videoen lærerik? Så lik den og del den med vennene dine!
Nettside: www.bildeler.no/
📢 Bildeler.no på sosiale medier:
Facebook: / bildeler
KZread: / @bildelerno1
LinkedIn: / norsk-bildelsenter-as
Instagram: / bildeler.no
Пікірлер: 117
Excellently done. Especially prying off the control arm. You don't need to remove casting from the shock though. It works on the car. But for this video it sure makes it clear. His bearing came out much easier than mine. Mine was so tight it destroyed the roller bearing. Freezing was a great idea too. Mine did not want to go in straight. It started cock eyed and did not appear that it would straighten out so I ground out a bit of a chamfer in the casting and then carefully tightened and measured and tapped it until it was straight. But then again mine was very tight coming out so it had a tighter press I think. Note when he used a press it popped when it straightened out. Make sure you PRESS IT ON ALL THE WAY! I thought I did, but there was maybe a 1mm gap. I put it all together, and the disk was too far out and it rubbed on the brake casting. I ground it off so it wouldn't rub, but the ABS was faulting. Too much gap. So.... have to tear into it again.
Now only if I had a nice sturdy workbench and vice I'd be all set after I'd buy this tool. Cool!
Good job . thanks !
I have to say you show a better way to to remove the barings from hub assembly than ford.
An extremly well done video! Thanks!!!
Nice job of using the correct tool. I am not sure if you saved much time by placing the new hub in the freezer.
very profecional,thanks
Your videos are great. I wish , you wrote the instructions in the video were in English too. Though , the video is well organized and informative , we need to understand the instructions in the video. Thank you again
👍
Bel lavoro
Muy interesante, ese tipo de herramientas.
Muy buena herramienta amigo
ممنون واقعا عالیه
Excellent
Hola , cuánto tiempo se deja el balero en el congelador gracias por el vídeo
👍👍👍👍👍👍👍👍👍👍👍
Good job 👏
amazing tools
Outstanding
I like this. I want it, I need this