Awesome stuff! Do you think it's possible to have multiple outlets so all your mates can plug into your hot dog at once? 😅

@JCYT

Жыл бұрын

Hahaha plenty of hot dog to share with the boys!

Thanks Jono Love RE watching your vids! Reminds me to drain any condensation out of my tank too

@JCYT

Жыл бұрын

Thanks for watching! And thanks for the reminder too to drain the tank.... haha

Awesome and clean work as always ☝️

@JCYT

Жыл бұрын

Thanks CGR !

Nice mate. Will be following this video to do mine too

love your work mate

@JCYT

Жыл бұрын

Cheers mate Happy new year

Very neat install Jonathon, only suggestion I have is to add on the Arb air pressure control module. You control it on your phone via an app, you can have preset pressures eg road, sand etc. I get out of the car, plug on the hose and turn on the compressor, choose the preset and connect the hose to the wheel. It inflates or deflates to the set pressure automatically and I believe it deflates the 4 tyres in a faster total elapsed time vs the dedicated deflator as your not wasting time screwing the deflator on, removing the valve and then in reverse afterwards. I don’t even bring my deflator and inflator chuck any more.

@JCYT

Ай бұрын

Hi mate thanks for letting me know! I'll have a look into it. Sometimes i do run my pressures different front and rear so it may not be suitable.

@ilove2explore

Ай бұрын

@@JCYT I run different pressures front and back. When it starts to do the first rear tyre I up the target pressure by a couple of psi, it’s very flexible

Clean install mate keen to see what else is happening with the 79 becoming a neat build!

@JCYT

Жыл бұрын

Cheers bloke! Hopefully it wins you over

@Marcuss___

Жыл бұрын

@@JCYT if it was a 76 or a n80 it already would have time will tell though

Absolute legend johnathan so much knowledge and so tidy with everything you do mate. Would love to see more detail of you running your wires under the ute for the canopy 12v build 👍👍 absolute brilliant

@JCYT

10 ай бұрын

Appreciate the kind words! I'll do my best to include it in that video as it's currently a work in progress. Thanks

@michaelhickey2015

10 ай бұрын

@@JCYT can’t wait mate👍

I see Jonathan Jr. grabbed the brake line cutting tool @3.29 ready to help out with the install.

@JCYT

Жыл бұрын

Hahaha getting ready to burn daddys bum with the soldering iron!

Some great content.. keep it up, following with interest on how this build comes together

@JCYT

Жыл бұрын

Cheers mate hope you enjoy the journey!

شكرا على المجهود وعلى الشرح

Nice job 👍👍

@JCYT

Жыл бұрын

Thanks mate!

Niiiice job man 👍👌

@JCYT

4 ай бұрын

Thank you!

This video was great. I just bought my new canopy/tray and wanting to do this. Thanks a lot. Instructions were excellent.

@JCYT

Жыл бұрын

You're welcome mate hope it works out! I ended up getting rid of the circuit breaker and installed a MIDI fuse in its place The circuit breaker kept tripping on hot days (it was a low quality eBay spec one though). It's been otherwise perfect with the midi fuse.

Neatly done mate, awesome work👍🏾... Hey man one thing that captured my attention was your side step. Could you care to explain, please tell me about it.. Do a video about your side steps....Dang my first time to see something like that..😀

@JCYT

Жыл бұрын

Thanks for your comments of support! You will have to stay tuned for the 10000k 1 year+ review! They are clearview e-boards I like them... but yeah don't love love them

@shannonpiruruho322

Жыл бұрын

@@JCYT Awesome thanks for the reply!

jack the side of the car a little bit, the compressor doesn't have to fight the vehicle weight and pressure inside the tyre at the same time.

@dustyfarmer

Жыл бұрын

You could spray the front of it with WD40 too so it slips through the air better.

Such a mint truck! I want to order one but I might of missed the boat!?

@JCYT

Жыл бұрын

Cheers mate If you reallyyy wanted one, there are about 2-3 new ones sitting on the used car lot at every dealership. There's a clear reason people have missed the boat...

I'm about to do the same install expect with the provided ARB tank. Why did you run an additional relay? My understanding is there already is one? Was the circuit breaker required? I know little about 12v.

@JCYT

Жыл бұрын

Hi mate! There was no additional relay used. The ARB switch/relay is a 2 in 1 so the switching circuit I have left completely as designed by ARB. You will need to run an additional circuit breaker to protect your new cable against short circuits which is a possibility in the event you're in a car accident. The two small 40A maxi fuses are to protect the 2 x arb compressors (on the twin compressor).

Hey mate just wondering how you wired the switch? Also the supply from your compressor is that coming from a main battery or Aux? Cheers

@JCYT

9 ай бұрын

Hey mate The switch comes prewired out of the box from ARB and the only wiring I really needed to do was to supply power from the main battery. Best way to do it - I would avoid wiring direct to aux battery unless the battery bank is huge! It's just a relay switch, wouldn't be hard to do with any standalone compressor.

How did you get power to the switch? I've pretty much done the same thing just stuck on running red yellow switch wire to power

@JCYT

7 ай бұрын

Hey mate As it came straight from the portable box, it was prewired and bolted straight in with two cables going direct to battery. If you've bought the compressor separate, you'll need a relay to control the compressor via a switch. Hope that makes sense

Great video mate. Could you list the parts/website for the additions filler pipe? Other than the 90 degree pipe from Mackay . Cheers mate

@JCYT

Жыл бұрын

Hey mate the alloy pipe was existing from the norweld tray however entire filler neck could be substituted by 2 90 deg hoses (1 of them will need to be a long leg hose) + 1m 50mm OD alloy pipe depending where your filler is. Thanks for watching!

@JamesEastham

Жыл бұрын

@@JCYT thanks heaps for your reply mate!!!

@JamesEastham

Жыл бұрын

@@JCYT hi mate. Will 1.6mm thick alloy work ok or should I go the 3mm?

@JCYT

Жыл бұрын

@@JamesEastham1.6mm will be fine!

@JamesEastham

Жыл бұрын

@@JCYT thanks. Really appreciate the reply

What is the wire awg used for the extension? Both red and black?

@JCYT

Жыл бұрын

Hey mate 6AWG

@JCYT

Жыл бұрын

Yes for both positive and negative. Twin core

@abudllazizalghanim8728

Жыл бұрын

@@JCYT thanks for the info

Since when has a ute been called a car?

@JCYT

2 ай бұрын

He identifies as car 🥲