Ansys Fluent Meshing using Watertight Geometry Guided Workflow | Ansys Virtual Academy
Ғылым және технология
Subscribe to Ansys Virtual Academy ►► ketiv.com/academy/ansys-virtu...
In this session, join KETIV Application Engineer, Snigdha Sarkar as she goes over the guided meshing workflow for Watertight Geometry with clean CAD in Ansys Fluent Meshing. This session follows the easy and intuitive steps in the guided workflow to auto-generate a high quality CFD mesh in Fluent meshing. Some of the important steps that are covered include:
-Introduction to the watertight geometry workflow GUI and features
-Surface meshing using guided workflow
-Volume meshing using guided workflow
This session is highly recommended for CFD analysts who are looking to reduce their simulation pre-processing time, and simplify their CFD workflow by taking advantage of Fluent’s single window workflow from geometry import to meshing, solving and post-processing.
Follow us:
Facebook ►► / ketivtech
Twitter ►► / ketivtech
LinkedIn ►► / ketiv-technologies-inc
Subscribe to our blog ►► ketiv.com/blog/subscribe/
#KETIV #AnsysVirtualAcademy #Ansys
Пікірлер: 46
Awesome Lectures, you are truly celebrating knowledge!!
Hi. Question. Should the body of influence be a separate part? I'm using designmodeler and not spaceclaim, but i don't think that makes a difference right? Reason is, I tried to form a new part, but it couldnt identify the boi. Thanks!
Amazing!!! Learnt so many things from here and mainly the polyhedral mesh.
@KETIVTechnologies
3 жыл бұрын
Glad we could help!
hi, thats great job. is it appropriate to use dynamic mech with poly-hexcore mesh ?
it was a paper of Roach, for mesh Independence study. one may use also richardson's extrapolation method
Thanks Snigdha. It was a very nice learning.
Hello, question here on capping. I want to import cad files from autodesk inventor. How can i seal inlet and outlet when i dont have it already prepared? In autodesk CFD mesh creation started at the end, after all other settings, including materials and internal volume definition, so there you were still working with CAD edges and not triangular mesh.
Hi! Very helpful tutorial! I wanted to know more about how to improve the mesh in terms of skewness and orthogonality. Hopefully you could provide a tutorial on this as well, thanks!
@erwinphillipcabanban5582
3 жыл бұрын
Additionally, if I use poly-hexcore as in the video, how do I know if the orthogonality of my mesh is good? What value should I aim for?
hi very good video I just want to ask in case there is an interface what should I do to identify it
Hi. What is the difference between a solid domain and a fluid domain?
Say you make a mutlibody part in Design Modeler, you arive to Fluent, and you'd like to setup boundary conditions, in the BC tab. There will be listed several entities, each belonging to a separate body of a multibody part, that belong to a same boundary named selection (face), say outlet. Is there a way to merge them and prescribe the boundary condition over the whole face rather than separately? Thanks
Impressive demo,totally solve my promblem.
I am using fluent 18 and there is No workflow window when opening fluent meshing is it not available in fluent 18 version or is there anything i should do to enable it from my side
Can we create Named Section at Ansys fluent instead of Space claim?
Yes awesome and quick but important
@KETIVTechnologies
4 жыл бұрын
Glad we could help! Be sure to visit our blog for more tech tips like this! ketiv.com/blog/
Really good narration 👍
Can you please provide this geometry so that i can practice in my system?
Awesome 🙏🙏🙏🙏🙏. The best one.
@KETIVTechnologies
2 жыл бұрын
Thanks for watching!
Can I get cad file for this workshop?
Great tutorial. One quick question: what is the advantage of using poly-hexcore mesh compared to all poly mesh? Thanks.
@johndao8592
3 жыл бұрын
Hello Ran, Our Ansys partners answer this question best. Please take a look here: www.ansys.com/products/fluids/ansys-fluent/mosaic-meshing-technology "Generate Mosaic-enabled Poly-Hexcore meshes up to 10x faster using parallel processing. The patent-pending Mosaic algorithm creates adaptive conformal mesh interfaces for the best combination of speed and accuracy. No need to buy a separate HPC license. The following example shows a comparison between Poly-Hexcore with Mosaic technology and conventional all-polyhedral meshing technology with a bluff body flame holder. The Mosaic mesh had fewer, better quality cells, requiring one-third less memory, and delivered a solution two-times faster with higher accuracy." Sincerely, JD, from KETIV
@KETIVTechnologies
3 жыл бұрын
Thank you John!
At 43:01 the minimum quality is 0.11, how can we refine that! Also for next videos if you go through skewness and orthogonal quality individually, we can see how good the mesh quality is and how it can be improved. Secondly, by looking at polyhedral mesh we can see compromise at the orthogonality, so, are there limitations to application of some turbulence models because of low orthogonality? Thanks and keep up the good work!
@KETIVTechnologies
3 жыл бұрын
We will cover mesh refinement and compliance with mesh quality in a future AVA. The purpose of this AVA was to highlight the ease of use of this task-based workflow, hence mesh quality wasn't prioritized. Thank you for the feedback! Snigdha Sarkar | KETIV | Applications Engineer
How do I create zones on stl of my geometry? I am not able to understand how I can create inlet and outlet
@fritzchennummber1
3 жыл бұрын
kzread.info/dash/bejne/ZJet2caJktK-qdo.html here you can see a workflow for opensource cfd with OpenFOAM, there it is mentioned how to create inlet and outlet for STL. If you are interested in creating Inlet and Outlet for a STL in SpaceClaim, then look for the Groups Setting by the modell tree. Hope this helps
Excellent
@KETIVTechnologies
3 жыл бұрын
Thank you! KETIV | Marco
Can you please include tutorials on how to mesh rotating fluid domain such as Horizontal axis wind turbine? I believe this kind of meshing involves at least 2 different fluid domains..
@xuxu119
2 жыл бұрын
I was also looking for this workflow on youtube but as far as i know the watertight geometry workflow only allows for 1 domain, meaning the interface layer for the MRF between rotating and stationary part cant be created. In the fluent solver you can however split the zones/wall to create an interface but I havent had any luck with that either and i think the shared topology erased all the interface lines. I am looking forward to someone showing me a working MRF under the watertight workflow.
Is it possible to generate structured grids using Fluent Meshing?
@fritzchennummber1
3 жыл бұрын
I dont know if its possible, but it is definitely possible with Ansys Meshing or ICEM.
How do we define rotating parts in fluent meshing? Thanks :)
@KETIVTechnologies
3 жыл бұрын
We will be covering rotating machinery in a future AVA where we will be covering mesh setup. Make sure you subscribe to our channel to watch that video when we publish it. Thanks!
@furkanyildirim76
3 жыл бұрын
@@KETIVTechnologies Of course I have subscribed :))) I am waiting for it thanksss
@xuxu119
2 жыл бұрын
@@KETIVTechnologies Looking forward to this. I thought the watertight geometry workflow only allows a single domain so MRF rotating studies cant be done under the watertight geometry workflow. Is this true?
I cannot get how to export the mesh in .msh format in order to convert it into openFOAM
@kumareshselvakumar4050
Ай бұрын
Yes, did you found a way ?
Good
@KETIVTechnologies
3 жыл бұрын
Thanks!
If you could do a video on How to improve the mesh quality (in terms of skewness and orthogonality) and how to perform that? it would be great..
@KETIVTechnologies
3 жыл бұрын
We will look into that for a future video. Thank you! KETIV | Marco