When hooking up the vacuum line, it is suppose to drop the pressure. It is compensating for the vacuum in the intake. When you have vacuum in the intake and the injector fires, the vacuum sucks more fuel through the injector,. So the drop helps maintain the delta across the injectors. Just when you go into boost, it raises pressure to offset the boost pressure in the intake. Works both ways.

@PNW_Car_Mods

Жыл бұрын

100% correct sir!

Thanks for the video! They are getting damn good at the cloning

@PNW_Car_Mods

10 ай бұрын

No Doubt! I think after this video that sometimes they may be even better than the originals.

I've never used the PQY regulators, but I've used several other China ebay regulators and always had good luck with them.

@PNW_Car_Mods

2 жыл бұрын

I can't remember for 100% certain but I think it may have been on of your videos I was watching that gave me the thought to make this video lol. So far the china regulator is outperforming the expensive regulator in function. Thanks for stopping in sir. :)

@BadLuckGarage

2 жыл бұрын

@@PNW_Car_Mods Honestly I’ve had higher failure rates with Aeromotive than I have with the China knockoffs. Which is sad really. I think I actually mentioned it in one of my videos but the last Aeromotive regulator I bought was probably 10 years ago and it lasted less than 6 months before the diaphragm got a small crack and started causing erratic pressure issues. In their defense Aeromotive actually sent me a new diaphragm free. But I decided to try a $35 China knockoff after that and that regulator lasted me for several years with no issues, then was sold with the truck and to my knowledge is still functioning today. Since then all I’ve used on my builds is the China knockoffs. The one I currently have on Chaos Theory is an exact knockoff of the Aeromotive 13301 but was like $25. It’s the first time I’ve used that design and it’s a lot smaller than the ones I generally use so I just wanted to try it out. So far I think it’s doing ok but we’ll see.

@marshall8490

Жыл бұрын

I like that fuel psi gauge where did you get it from?

I used a PQY regulator until I needed bigger I/O at 10an. They work 100% just as good as a top dollar Holley or Aeromotive. I never had any issues at 60psi of base pressure up to 74psi with the boost ref hooked up.

@PNW_Car_Mods

22 күн бұрын

Good to hear. I'm still having no problems with them. I am currently running an 8AN PQY and working perfectly. Put the 6an PQY on my ls swapped Ranger and it lives on there.

Thanks for making this video. Your car looks immaculate. :) I was watching the entire video but it didn't address my "problem". How long does your regulator hold the pressure? Mine drops from 58psi to 43psi as soon as I shut the engine. Then it climbs down very slowly (15mins) to about 14 psi. In 1 hour it shows zero. Watching the video I can see that your regulator acts the similar way. So is this a problem or not? Many say that regulators should hold the pressure for about a day before the pressure starts to drop. Is that true with these regulators or that statement applies to stock regulators only? I just want to find out if this pressure drop is totally normal or a faulty regulator.

@PNW_Car_Mods

5 ай бұрын

Mine drops fairly quickly most of the time. Some days it will hold half for like an hour but most of the time it drops to half within in a minute or two and drops to zero within a couple hours. I have never seen a non factory system hold pressure myself. That being said the simple answer is, does your engine start as it should? If yes, then don't worry about it.

Bring one feed line up into y and split off to each rail. And in the front use the regulator as the crossover, for lack of better words. That should fix that fuel pressure problem

@PNW_Car_Mods

28 күн бұрын

I have completely revised this deal since then. It is now a full loop an 8an regulator at the very end of the line and then returns to the tank. In other words it is no longer a stubby deadhead setup.

Has Mrs. Black ever come out to the garage and said to you; "What is it EXACTLY that you do out here ALL day?"

@PNW_Car_Mods

2 жыл бұрын

On no. She knows that I quit my full time career of 27 years to become a successful youtube star! LOL

yes! ty ty ty saved me $100 on my budget build 🎉

@PNW_Car_Mods

6 ай бұрын

Good luck with it! Still running 2 of these on a couple of my cars.

Do you recommend taking the pqy apart right out the box? Or can it be just slapped in? Did you ever test the fittings that came with the regulator?

@PNW_Car_Mods

Жыл бұрын

No, I would just put it in. I mainly took it apart just for the comparison of internals. I did not ever use the fittings. They are on the parts shelf as spares.

I recently bought the exact same one on Amazon and it was junk/faulty so sent it back. Would not regulate below 90psi some reason. Hooked up correctly but wouldn't drop pressure. Vacuum on or off was 90psi with screw all the way backed out. Ended up buying an AEM.

@PNW_Car_Mods

Жыл бұрын

That's a bummer Justin. So far mine is still going strong and absolutely works better than my Aeromotive did. That being said I don't hold it on a high pedestal either. It is cheap chi na parts. AEMs are good units and a lot of people use the Holley regulators as well.

@tsiawdspyder

Жыл бұрын

I may get another just to try again on my silverado that I'm turboing. That's the only bad about China parts is they're so hit or miss

@redinstrumental7535

Жыл бұрын

Im about to find out if I have the same problem I got one from Amazon doesn't seem to get much power after 25mph and it's struggling there's no more leak and smell so I just ordered one from O'Reilly's and I'm about to see if it's the Amazon faulty product.

Are u still running that ghost cam on the LSA 408…….im at the point where i need to get a cam and im just trying to figure out which route to go…..im at 9.8/10:1 compression with a 3.42 posi and 3000 stall built 4l65e…..the current 370 is 11.15:1 with a 220/230-.558”/.558”-117+4* cam and with the stall and gears with 2.45 pulley it works great and is very streetable and works with my vacuum brake booster…..id like the same with my 408 but i know the 220/230 cam would be like a stock cam in that big of a motor…….do you think a 114 Lobe seperation angle cam would be to narrow with our LSA blowers……should i just run with the ghost cam?? Do they make something a hair more aggressive…..if i recall you said you made around 650 whp with that cam right???…..i havent started to tear down the car yet so i have time to decide on which dierection i wanna go with the cam seeing as how my 15yr old son just recently talked me and my wife into getting him a ‘67 mustang coupe 289”…….were dailing it all in for him and im adding an efi kit for him (aces efi)…and at the same time we picked up a late model (‘96) 302 roller motor for us to build up together for when he graduates from that tired 200hp 289….. we got new forged flat tops and 58cc chamber aluminum heads to bring that anemic 8.5:1 cr to around 10.0:1 and hopefully over or close to 300whp (which is more than enough for a teenage boy in a 2800lb car thats over 55 yrs old)……ultimately id love to LS swap it but id have to fabricate some type of exhaust manifolds or headers along with the motor mounts…..so we just said fuck it and we’ll give the ford 302 a try considering its a dierect bolt in and all the misc. 289 parts will swap right over to the 302, including the ACES efi kit…..the efi kit even comes with a 3 bar map sensor….so if he is redponsible and does well and doesnt get any speeding tickets …….maybe, just maybe when he turns 21 we will bolt on a turbo kit…..that is unless theyve came out with a direct bolt in LS swap kit first……im just learning this ford stuff and its literally ass backwards too me😂😂😂……but between me, google, and youtube we’ll figure it out ……with the help of my paypal mastercard of course😂😂😂

@PNW_Car_Mods

10 ай бұрын

I am still running the ghost cam. I don't care for the way it sounds and it probably is a touch small for 408 cubic inches but god damn it drives so freaking well that I don't want to change it. At least not for a while. My take on any boost cam is more about overlap vs lobe seperation. You don't want overlap. The ghost cam has no overlap. Now I just wish they would make a plus sized ghost cam lol.

Ive got DW regulator for my MR2 wonder how it holds up

@PNW_Car_Mods

2 жыл бұрын

Can't ever imagine Deatschwerks ever selling a crappy part. Seems the most common from those I have chatted with are the offshore units and a lot of Holleys

Great video! Quick question, what is the min and max pressure this PQY regulator can be adjusted to? Thanks from the UK!

@PNW_Car_Mods

Жыл бұрын

I can honestly say I can't remember for certain. I want to say it's from like 20psi to 90 PSI. I may be off a little though. I run it at 58 PSI and there is lots of adjustment either way on the stud.

@seemaab

Жыл бұрын

@@PNW_Car_Mods is it 8an or 6an!

@PNW_Car_Mods

Жыл бұрын

@@seemaab I believe it is capable of 8an but I have 6an fittings in it.

@seemaab

Жыл бұрын

@@PNW_Car_Mods I just bought one and the seller said it’s psi rating starts at 60psi but the photo says 42psi. Same brand. Maybe he’s mistaken? Bought it from AliExpress

@PNW_Car_Mods

Жыл бұрын

@@seemaab I seem to recall reading something like that on the amazon site as well. It definitely however goes way lower than 60 PSI. Like I said before It will probably go into the low 30s if you back the adjuster all the way out. If you can find the adjustment span on the Aeromotive site the PQY will definitely do the same.

Still all good? For the most part everyone seems pretty happy with this fpr. Was worried at that price but think I'm gonna get one. Last piece of plumbing my fuel sytem

@PNW_Car_Mods

Жыл бұрын

These things are great IMO. I actually just took off the one in the video to go up to PQYs 8an version and even though it weighs a ton I think it works even better. To be fair though my configuration changed. I would highly recommend either of the PQY regulators.

@jess6972

Жыл бұрын

@PNW Car Mods & Maintenance awesome! I ran 8an feed 6an return so that's actually the one I was looking at. Thank you for putting my mind at ease

@PNW_Car_Mods

Жыл бұрын

@@jess6972 Yup no problem. That is how I am running now. 8 feed 6 return. My most recent video is a long boring video of the install of the regulator and new PTFE lines.

Been thinking about that regulator.. is it using 8an inlet and outlet? Or 6?

@PNW_Car_Mods

Жыл бұрын

It is set up for -6. You could run 6orb to -8AN and it may be slightly better but if you truly need -8 flow you may want to get a bigger regulator.

I find this PQY thing on several sites for 30 ish dollars/euros is that correct? or are these some fake knockoff...? Seems quite nicely build compared to most ebay/china regulators...

@PNW_Car_Mods

2 жыл бұрын

That should be the right one. I paid about 35 dollars for the PQY. So far it is working perfectly.

its the gauge, You need a gauge that vents to the atmosphere. aeromotive addresses this.

@PNW_Car_Mods

10 ай бұрын

Using an autometer pro comp mechanical. There is an absolute difference between the two brands. The PQY flat out worked better IMO.

im asking who knows more about these items. is it possible to use one of those aftermarket fuel pressure regulators, for the old Mercedes W124 series that have KE Jetronic? the Bosch regulator costs so much .... its prohibitive the price. please help, thanks in advance

@PNW_Car_Mods

Жыл бұрын

I am too unfamiliar with the Mercedes system to say for sure. These regulators will usually regulate from between 35 and 75 psi or so. Also it could be an additional challenge getting fittings to hook up into the factory system.

I scanned your channel quick but couldn't find an update video. Are you still happy with this regulator?

@PNW_Car_Mods

8 ай бұрын

Yes indeed. I would buy another one in a heartbeat. I am actually now running PQYs 8an larger style regulator in this car now and it performs equally as well!

@woog74

8 ай бұрын

@@PNW_Car_Mods Thank you for the reply!

11:00 probably wouldn't hurt trimming back those fittings a bit for a little less restriction.

@PNW_Car_Mods

2 жыл бұрын

I will keep that in mind if I ever feel like this thing is running out of fuel. Thanks shinedown

@shinedowncannel

2 жыл бұрын

@@PNW_Car_Mods No problem. Thanks for the comparison!

Seems like my aeromotive regulator gets stuck while trying to get into boost. Would I have to take it apart and clan it?

@PNW_Car_Mods

11 ай бұрын

Mine was sticking as well and I couldn't find any logical reason for it. The PQYs have never acted sticky and work perfectly for me. I would say take it apart and look for anything wrong and if you can't find anything wrong maybe try one of the cheap offshore units.

Just got mine and the body is also drilled and tapped off center. Gotta wonder if these are aeromotives that didn’t pass QC. Rock on!

@PNW_Car_Mods

Жыл бұрын

I'm not sure but I will say that so far the PQY out performs the aero just in much smoother operation by watching my fuel pressure gauge. I'm keeping the cheap one on the car.

@lukasethan6429

Жыл бұрын

Just for my experience in aircraft engineering in management for a large company usually there off-center so when they put them in the fixture, they only go one way. I’m almost certain it’s off center for a reason like that. I could be wrong just my two. Cents.

@PNW_Car_Mods

Жыл бұрын

@@lukasethan6429 That very well could be. but interestingly enough the usa made Aeromotive unit is perfectly symmetrical lol. I just wish the aeromotive unit worked as well as the china unit. :(

odd, you think it would go up if anything. did you check the vacuum at hose?

@PNW_Car_Mods

2 жыл бұрын

only with my finger cole. it definitely sucks at idle and it definitely boost references. Like I said in the video the aeromotive works it just seems to act weird and I may very well be chasing unicorns lol.

@colemcmeans7809

2 жыл бұрын

I have gotten good at chasing those unicorns never caught one though.

Rooting for PFi, Boostedboiz, or Garrett :)

@PNW_Car_Mods

2 жыл бұрын

Subbed to your channel CP. I tell you I am a massive youtube junkie. I watch more than a make lol. I am following probably 22 cars at Sick Week. To many favorites to list them all but I am a massive supporter of the Cleetus operation from day one. Get a little bummed out when when I see how much shit he gets at these races but on the same token I get it to. Great race this week for an inaugural event.

@MotorSwapDan

2 жыл бұрын

@@PNW_Car_Mods total junky here too dude ! Fleet has the backing to keep going I dont worry about him. Any failure for these guys means good vids either way good or bad. Are you north or south sound?

@MotorSwapDan

2 жыл бұрын

*cleet has the backing...

@PNW_Car_Mods

2 жыл бұрын

@@MotorSwapDan Yeah he's go the backing alright. I've probably given him 400 bucks in the last 5 years haha. We are in Pierce county by Thun Field.

🖐🏼The regulator still working properly?

@PNW_Car_Mods

10 ай бұрын

Yes. Still in use this day almost daily driven!

Thought it was suppose to drop. I thought it was supposed to increase one you get on the gas

@PNW_Car_Mods

Жыл бұрын

Yes it will drop and rise depending on vacuum and boost.

I am in need of a regulator for my stock LS1. What are your thoughts on this one after a year of operation?

@PNW_Car_Mods

6 ай бұрын

I have two of these now on two different LS cars that are driven a lot. They are still working perfectly! THat being said if you are working with a stock engine and it's not part of an engine swap you may just want to stick with stock parts. Keep it simple.

Great video 👍

@PNW_Car_Mods

2 жыл бұрын

Thank you Irving.

@irvingbar4569

Жыл бұрын

@@PNW_Car_Mods’m running a 5.3 ls 7875 turbo build should my fuel gauge sensor read 43 psi at the rails I have 76lbs injectors from Holley that run on 60 lbs and should I adjust with the vacuum plugged thanks

@PNW_Car_Mods

Жыл бұрын

@@irvingbar4569 It just depends on what you want to run the system at. GM stuff is normally 58 PSI with the vacuum disconnected and plugged. Some tuners do run lower base pressure though. Even as low as 40psi. I personally use 58psi set with vacuum hose disconnected and plugged. When the hose is put back on on my car it runs around 50psi.

@irvingbar4569

Жыл бұрын

@@PNW_Car_Mods is there any way I can email you some pictures i would really appreciate the help

@irvingbar4569

Жыл бұрын

@@PNW_Car_Mods when I unplug my aeromotive fuel regulator and cap my intake I set the fuel regulator at 43 but when I plug the fuel pressure regulator back to the intake it drops to 37 fuel pressure is that normal

Hint. Used Nascar filters/hoses/lines.

@PNW_Car_Mods

Жыл бұрын

Because Racecar!

@zacharyohare6029

Жыл бұрын

@@PNW_Car_Mods And you get that $200 filter for 25% of that, and buy a new element for $20. Then tell people you built your truck with NAAAASCAAR parts so it's automatically cooler. :D Seriously though, same for dry sumps, fab a pan, run a good used pump, lines etc, because those fittings and lines will kill your budget.

@PNW_Car_Mods

Жыл бұрын

@@zacharyohare6029 It's funny you bring this up as I literally am currently rebuilding y whole entire fuel system on this car to meet the demands of the new engine combo. 95% of all the hose and fittings is evil energy and pqy. all with PTFE hose and switch to 8AN from 6AN. Just put a new 8AN PQY regulator on the car yesterday as well. Seems just as well built as the one in the video.

made in China? both of them??

@PNW_Car_Mods

2 жыл бұрын

Negative the Aeromotive is USA machined and made.

i have a turbo subaru = run`s 43psi - i put 45 and not running = start up with the vacuum boost host - 39psi - at idle big turbo std cams automatic = rising rate regulator = GREAT !

@PNW_Car_Mods

Жыл бұрын

Good to hear Ronnie. This regulator is still working great for us. We're set to 58 hose off and around 51 hose on. Goes into the low to mid 60s at 12psi. Love it. No doubt in my mind that it is smoother and less sticky than the Aeromotive was.

@MrJDRACING

11 ай бұрын

@@PNW_Car_Mods it should read 70 psi at 12 psi boost whit a 1to 1 regulator base pressure plus boost pressure if you dont you have a fuel problem pump, line , fuel filter dirty

you need a fuel pressure sensor in there

@PNW_Car_Mods

Жыл бұрын

I agree. I just don't have anyway to log it without going to holley or such.

@Boosted370

Жыл бұрын

@@PNW_Car_Mods Ah I see I see. Putting a Dominator ECU in my 91 Z28 was the best thing I ever did. Yea it's pricey but worth ever penny

@ArcticSniper1000

5 ай бұрын

@@PNW_Car_Mods Rig the fuel pressure sensor into the AC switch. Most cars use a 5v signal for the AC pressure switch. On Mustangs, we just unhook the pressure sensor and stab the fuel pressure sensor into the three pins of the AC sensor. One is power, one is ground, one is data/signal. It'll then show up in HPT or Holly or whatever program as AC pressure, but you're actually logging fuel pressure. Just be sure to edit the fan settings so they aren't full blast wondering why the AC pressure is at 3-4 volts

@PNW_Car_Mods

5 ай бұрын

@@ArcticSniper1000 I've heard of this before and thanks for the simple explanation of how it works. Only problem is that this car has fully functional AC and I actually use it in the summer. There's no way you could parallel that line I don't believe unless I am missing something?

I can tell you your pqy will fail.. just a matter of minutes or days

@PNW_Car_Mods

6 ай бұрын

lol

Get stand for your phone.

@PNW_Car_Mods

8 ай бұрын

That would be pro level stuff right there. Seriously though I do have one now for both a go pro and my phone. I rarely use my phone.