Great to see these older tools being restored and not just thrown away. Plenty of more Jacks in the background ready for refurbishment, so there’s quite a need for it. 👍🏼

@Happy357mag

4 ай бұрын

Often, people in the West throw out things that aren't even broken. They also would rather buy new than get something fixed. That's fine with me because I then get some free stuff. It's interesting how these guys specialize in only one thing.

He needs to restore that bench grinder next!

Wow, that bench vice! Must be built to last for generations!

Great job, 😊

Hadir JawaTimur saya senang kalau melihat alat2 yg sudah rusak di perbaiki 👍👍👍

You work with what you have, nice job considering, I’d have done it a bit different, but I’ve got access to more resources

Great Work !!

Muy buen trabajo grasias por compartir..

Good work 👍

Very good

Dude actually has a modern lathe. It's also clean to boot.

The old Ritchie Brothers overhaul I see

Show de bola

Это не ремонт и не реставрация,это имитация работы.

@paseoenmotouy

3 ай бұрын

kzread.info/dash/bejne/hn6Kk9exqdzPp8o.htmlsi=BpcLbGGLp2TnU7zM

Молодец

Machaalah

inilah bezanya negara kaya dengan negara miskin. bagi kami negara miskin kami menghargai apa yang kami ada. selagi masih boleh digunakan kami akan memperbaikinya. kemiskinan membuat kami menghargai apa yang ada......

Dari cara kasar proses yg kurang teliti Saya kurang yakin pemulihan ini bisa bertenaga full seperti semula

Главное покрасить! Теперь можно смело сдавать в металлолом.

Surely the parts needed a wash.

اعاده ترميم عفريته

What country?

❤❤❤❤

Acho que esse povo não sabe o que são 50 toneladas.

Repair cost of 2k thn buy new one 1k only😂😂😂😂😂

Do you not wash the parts before painting

@sakuraturbo3364

3 ай бұрын

Primer is prohibited in this country

Aapka adress milega

"... не ведают, что творят..." У каждого запасные глаза, пальцы, лёгкие. Идиотизм зашкаливает.

Это не ремонт!

रबड़ सील कहा मिल ता है बताओ गे

@paseoenmotouy

3 ай бұрын

kzread.info/dash/bejne/hn6Kk9exqdzPp8o.htmlsi=hhpvUUzQgpVDBXGz

He took the angle grinder,ground the outer diameter two different directions,then buffed the cylinder. I didn't notice him measure anything for out of round or taper. If it works ,he is very good or very lucky. Maybe he's a professional back yard mechanic.

@rxpsycho7326

4 ай бұрын

He only ground the lift piston surface not the sealing area or the ring landings. Worst that could happen is a slow drift from scoring inside the cylinder walls. Better refurbishing than some others I’ve seen.

@paseoenmotouy

3 ай бұрын

kzread.info/dash/bejne/hn6Kk9exqdzPp8o.htmlsi=hhpvUUzQgpVDBXGz

@inothome

3 ай бұрын

That cylinder only uses pressure to extend, not retract. So rod diameter / taper is irrelevant in this case.

@antoniof0nty

Ай бұрын

You certainly don't know how a hydraulic jack works. There will be no sealing problems as long as you do not modify the inside of the cylinder. The seal acts on the inside of the cylinder. The exterior is irrelevant.

Ну про 50 тонн это перебор, от силы 15- 20

покраска 500лвл

You mean 5 tonne ?

Он ничего не поднимет потомучто это мусор😂

They haven’t heard about primer

WHy not oil treads all to do with cost

В конце жесть. Покрасили всё что есть собранным и грязным.

дайте краски ЯВУ покрасить.

👓👓👓👓👓👓👓👓👓👓

No way in hell this jack is 50 tons

I don’t know Rick I wouldn’t trust that Jack

I wouldnt trust these jack

no under coat will rut in five minutes

This should work on 50 tons ? How long ? 2 minutes ? 👎

Failure rate 50%, safety rate 2% , Job security 200%... Not sure if the parts are comparable looking at the work bench. i only pray for the soul that uses this... overall -20% success. peace

@corazonperalta9321

2 ай бұрын

..................................fyuyy780knjhhhukkkkĵjjĵnlkjhyy89000 p 099 f h

@jeandebuis1732

2 ай бұрын

❤😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😂😂😂😂😂z😢z😢😢😢😢😢😢😢😢😢😮😮😮😮rr5😅 pour 😅😅6 pas 666t qQQQQQQQAAAAAAAAAAAÀWWWWWWWXWXXXSSSZ

@RohithaLakshman

Ай бұрын

😊

15 ton !