I have one and I use a dewalt 12v lithium battery. I soak all of them in sea foam (in a jar) in my ultrasonic cleaner and I connect each one to the tool set on steady pulse for about 10 mins each. I take the o ring off each injector as I disconnect from the power so that I can keep tract of which ones have been run while soaking and cleaning the entire set. The jar allows me to fill the cleaner with only water and after I finish I simply remove the injectors and cover the jar and set it aside for the next time I need it.

Nice video! Straight forward without bs. Thank you!

@AliMECH

27 күн бұрын

Thanks

Put an on/off switch on the positive side from battery to reset

how did i not find this channel before, great work man

@AliMECH

2 жыл бұрын

Thanks for your support, appreciate that

@difsid569

2 жыл бұрын

@@AliMECH you're welcome keep up the good work 👍👍👍👍

شكرا لك حقا استفدت من هذا الفيديو ❤

@AliMECH

Жыл бұрын

🙏🙏

Thank you. Great video.

@AliMECH

3 ай бұрын

Thanks for watching

How much ohms does Siemens DEKA injectors supposed to be and question what you use to stop the fluid from coming out from the hose when u sprayed it with carb cleaner like how you sealed it so it won't leak

Wowww nice

What size rubber stopper did you use to attach the spary nozzle?

Can I just tape down the cleaner nozzle to the open position? Will that be too much pressure?

may i use cleaning clean set and pulse device together in my workshop with ultrasonic cleaner ?

👍

Question. When you pulled the injector out, was the metal tip extremely gunked up with burnt oil and carbon? Mine look terrible, not sure if that is expected or if i have a failed seal somewhere

👍👍

Very good

@AliMECH

2 жыл бұрын

Thanks

Thank you Sir

@AliMECH

Жыл бұрын

Thanks for watching

siutable for DI injectors aswell ?

If i do nit have tester can i open it wuth a 12 volts

Can i use continental diesel injector testing

Can it be used for diesel crdi injector ?

👌

@AliMECH

3 жыл бұрын

🙏🏻

you should install an ox/off switch so to don't disconnect the cable from battery. aniway good job

@AliMECH

9 ай бұрын

I did after this video

Just use a momentary switch which is normally closed type, in other words when not pressed it's always on, when you press it switch off.

I like your steering wheel where do I get one like that and does it work also

DIY adapter... how you make? I see hose and clamps... what is connected to red hose inside to seal? Thank you Great job by the way.

@CHEVI789

Жыл бұрын

He uses acidic silicone I'm sure.

to change the mode i believe you don't have to disconnect the battery.. there is a reset button, top left-hand side... at least mine has

@denzelcrocker4956

Жыл бұрын

Can you Tell me, If i can Clean my injectors with That Gadget without an Ultra Sonic cleaner?

❤

@AliMECH

11 ай бұрын

🙏

How can I buy one like this, thanks for helping...

@AliMECH

3 жыл бұрын

O problem, I put the Amazon link in the description box of the video

Can I use it in the car?

How can j get this machine

Is it safe for motorcycle injector

Why when I connect my injector or reconnect to battery it clicks?as if it engages. And when I spray the cleaner and active the tool it sprays very little as if it doesn’t engage it properly. What do you think is going on?

@rafagas5150

Жыл бұрын

I could really use the help thanks

@jessstrunk6102

Жыл бұрын

@@rafagas5150 Did you figure it out? Every time power is applied & removed the injector cycles or clicks. Power open and depowered closed. When power is applied, you should see the same spray as your can nozzle come through the injector. That has been my experience. If not the same spray, its clogged or not opening all the way? I had an injector that would work beautifully on the bench. When in the motor, would work on cold engine or on interstate driving. However, when I would stop for gas refill or a short period, the injector would get hot and not work? I pulled it back out, on my test stand worked great. Used a heat gun, heated it to 200 degrees, injector would not work till it was cool again. It was the #4 cyl misfire on a 4-cylinder motor so it got most of the heat I guess off the motor. Good Luck

Can you use alcohol or peroxide to rest, instead of carb cleaner?

@CHEVI789

Жыл бұрын

Fuel creates gum deposits, I'd stick with a carb cleaner, trust me, that shit cleans real well, real quick.

Wait so how did you get the red tube clamped to the rubber hose?

@AliMECH

Жыл бұрын

I used glue

Does this work with delphi diesel common rail injector?

@MrMegaOliwer

Жыл бұрын

No

direct injected ?

How much this is Electronic injector cleaner

Need help,how we know the positive and negative connection of feul injector?

@AliMECH

3 жыл бұрын

It's a coil, doesn't matter which one is a positive or negative, it will work however you connect it

Where do you get the long straw?

@AliMECH

Жыл бұрын

It came with seafoam can

Witch company

Shit I just got it but didn’t realize I had to get a coupler for the injector. Thought it came with it. 🤔

How much

in your video you should have stated number four mode something is wrong and explain do i throw away or using the cleaning works we the audience would understand much clearer

You dont describe how we know that an injector is bad or good by testing with this machine ???

How do you get it? What is the price ?

@AliMECH

8 ай бұрын

s.click.aliexpress.com/e/_AMNAR7

How much cost

@AliMECH

3 жыл бұрын

About $27 on amazon

@explorehunter

3 жыл бұрын

@@AliMECH price increased now 😭

@terencejay8845

2 жыл бұрын

I paid £26 on UK Amazon. It's always more expensive than the USA Amazon.

Price

@AliMECH

11 ай бұрын

s.click.aliexpress.com/e/_AMNAR7

Hi Can you test a diesel common rail piezo injecter?

IT s for Diesel ?

It does matter what connection is positive or negative. You are incorrect, Solenoids operate open or closed. Reversing the polarity with close the injector, therefore NO fuel flow. Read a wiring schematic. It is still Ohms Law.