Alcohol Injected Blown 65 Nova Start Test, Idle to 8,000 rpm 100 2472
Fire The BEAST
Жүктеу.....
Пікірлер: 137
@petersmith2954 жыл бұрын
Watching them it was the most painful experience
@edmcclure87663 жыл бұрын
Money can’t buy you brains!
@rallydogmakes3861
3 жыл бұрын
?
@seabasschukwu6988
3 жыл бұрын
@@rallydogmakes3861 they were pumping the throttle... you don’t do that on a blown motor. It’s a big no no
@nonova703 жыл бұрын
Watched the video :( and went right to the comment section.... must say did not disappoint
@N2Otorious5 жыл бұрын
Excellent way to spin a bearing, fire up a cold engine, and go to whopping the throttle like that...This is why we can't have nice things.
@FIVE-0-APOCALYPTO
3 жыл бұрын
24 likes on your statement. Let's assume the build is done correct. I used to race. I also was part of a team. We had a good crew chief, he also built the motors. Very knowledgeable guy. We would run 15/1 C-16 fuel type motors. Callie's dragon Slayer, AFR, scorpion....good stuff. Crew chief: "The last thing I'm worried about, is that motor blowing up. It's bullet proof". A fresh build, one test on the Dyno, these engines are ready to go. Set the Rev limiter a couple hundred rpm short of the upper end starting to get unhappy and run that motor as hard as you want. There is no break in. The cylinder walls will warp oval before you spin a bearing. LONG before you ever spin a bearing. In fact, you will break something like a rod or something before spinning a bearing. And if something does break, even the crank shaft, it's almost ALWAYS because of something else. This isn't eldebrock, factory cast iron loose tolerance bullshit. This is high dollar, close tolerance, over kill metallurgy and specs. If there is important aspects that need heat or heat sink, it is designed to happen quick. It's not a issue. Not with these type of builds. When you race, it's not like you always have time to prep perfectly. Sometimes, you get rushed to the line. You fire it up, check your guages, get your slicks hot, hit the line, stage, hit the tranny brake, stomp the throttle, focus everything you got on the dying second amber and let the fucker go. Warm or a little cold, that motor will not give a fuck. It's built to go. It's not delicate. In fact, babying it would be risking a problem. Anyway, I don't see how you get 24 likes on a statement like that, unless y'all are just spectators. These engines, are bad ass. But it's not self destructive like top fuel. You race for a day or weekend, change the oil, run your inspections, make any adjustments or tweaks needed and it's ready for another weekend of pounding the throttle and the motor is very happy. That's the truth. What you said, is not true.
@welldonempofuu9842
3 жыл бұрын
@@FIVE-0-APOCALYPTO amen brother
@tylerbonser7686
3 жыл бұрын
@@FIVE-0-APOCALYPTO warming up a motor isn't considered babying it. While spinning a bearing would be one of my last concerns on a cold motor, revving the piss out of one is just stupid. It's not like you need to warm the engine up for 10 minutes right before you race but it is important to heat soak it before racing begins.
@nalley6815
Жыл бұрын
@@tylerbonser7686 um no. Heat soaked makes you run a lot slower lol
@tylerbonser7686
Жыл бұрын
@@nalley6815 then why exactly does every drag racer do it?
@lucasdorabiallo97793 жыл бұрын
your project is really cool, here in Brazil we have a lot of difficulty with the cost of the parts but we also have very strong cars ... our specialty is the turbo 🇧🇷🇧🇷🇧🇷
@SAtinnBlack
2 жыл бұрын
Sounds very interesting what’s the car scene like there?
@TT-di6qk
2 жыл бұрын
brazil sucks
@steveg.63736 жыл бұрын
Put some gas in your jug you use to prime it. And don't be scared to dump a lot of fuel in it when your priming it. Also keep putting it in until the pump gets it going. You will here it.
@user-jg6wx3lh1x
6 жыл бұрын
Fucktard, why would you use gas to light an alcohol motor?
@bryanswift8583
5 жыл бұрын
Hahaha Jesus Steve g is the man
@cardboardboxification
5 жыл бұрын
Steve G. Look up the enthalpy of the fuel goof
@N2Otorious
5 жыл бұрын
+Steve G. Hey bud I could figure out how to send you a private message, Man I'd love to chat with you and ask some questions. I have an 8-71 on a Big Block with an Enderle Big&Ugly... I'll have my engine back together soon and would like to ask you some questions that your experience might help me get this thing sorted faster. www.dropbox.com/s/pbvz7o0ryy0xg66/20180720_142939.jpg?dl=0
@andrewaharvey
5 жыл бұрын
Steve G. Have any spares your looking to unload
@lucasdorabiallo97793 жыл бұрын
what a spectacular project 👏🏻
@haroldhart26882 жыл бұрын
YEAH BLOWN-UP !!
@Foxbodyguy915 жыл бұрын
Bout time.... GEEZ. Nice build. Thumbs up
@ratcamaro6 жыл бұрын
Stay off the throttle. You're leaning it out. The guy on the bottle should be in control of the fuel.
@darkkinggaming7988
4 жыл бұрын
Exactly
@brian56062 жыл бұрын
The guy with the bottle is supposed to keep squirting or as they say bottle feeding the blower until the fuel pump can catch up and take over. One or two squirts ain't going to get unless the fuel system is really well thought out. Great car & video 👍
@N2Otorious5 жыл бұрын
He's pumping the throttle like a carb. Obviously he knows jack chit about engines.
@michaelmcneil5036
4 жыл бұрын
You don't pump a carb when rolling it over either
@konnerkramer329
4 жыл бұрын
@@michaelmcneil5036 why don't you pump are carb while cranking?
@michaelmcneil5036
4 жыл бұрын
@@konnerkramer329 I was just thought to pump before you start cranking because of too much fuel dumping into the carb
@sandstonefarm5722
4 жыл бұрын
@@michaelmcneil5036 yuup 3 pumps then fire it up also need to let it warm up befor you hammer on it too
@0hjaa3.06
3 жыл бұрын
@@sandstonefarm5722 No need. Pull the choke close and then start it. No pumping required. Otherwise is just dumps raw fuel out the pipe just for shits and giggles
@chrisortiz24662 жыл бұрын
The revs sound like thunder strikes
@rallydogmakes38613 жыл бұрын
I love it
@billclark59433 жыл бұрын
I get a kick out of pumping the gas on mechanical fuel injection
@user-tq1bs2fj9hАй бұрын
Let’s go racing!
@josephtalarico17496 жыл бұрын
haha hes used to burn soy sauce in his little honda .... also steve g. dont forget to shut fuel off before ignition so you dont wash down your cylinders and bend a rod
@garywood20963 жыл бұрын
I remember when I had my first beer.
@compoundlml7156
3 жыл бұрын
Hahahaha that's so funny the last time I heard that I fell of my dinosaur -Dale Doback
@centermass4962
2 жыл бұрын
Would u care for some fancy sauce?
@ivancook12474 жыл бұрын
Is that you toad in that beautiful car
@Robertm69964 жыл бұрын
Must not be a big fan of letting stuff warm up before you spin it 8000 rpm with no load on it.
@steven8075
2 жыл бұрын
builds of that caliber have oil warmers. motors like that can even lock up when cold so they have to be at temp before you can even try to start them. so yeah it's not a problem to start them up and rev them to the moon.
@Robertm6996
2 жыл бұрын
Thanks for the information. I had no idea👍
@poncoolride5 жыл бұрын
Why is he pumping tha goddamed throttle!? Dont do that on a blown injected motor!
@HyperKid36
5 жыл бұрын
never, never pump the throttle when priming a mechanically injected engine. big no no !
@nikolas812
5 жыл бұрын
Most of the people replying to this video have more knowledge than the guy that posted the video. I feel sorry for thst motor...
@chrisstuffel6819
Жыл бұрын
Testing the strength of the blower straps
@jg102xc3 жыл бұрын
A lot of experts in the comments here...
@salvadorhernandez34042 жыл бұрын
How expensive is this blown Alcohol race engine?
@backyardbuilttrucks12 жыл бұрын
Wow.
@christopherc49203 жыл бұрын
can you remove the first minute and a half?
@stevefodor4269 Жыл бұрын
Exactly
@19ADAM803 жыл бұрын
👍🏼
@michaelmcdonald30574 жыл бұрын
Why?
@justinhiggins22103 жыл бұрын
She didn't want to prime up.
@skimask97363 жыл бұрын
me in no limit racing
@joker_storm22323 жыл бұрын
That took forever....
@grumpyg93504 жыл бұрын
I think the diesel fuel has got water in it. My kubota does the same thing.
@adolphsfather4834
3 жыл бұрын
That isn't a diesel
@hd114ul72 жыл бұрын
Bought from some old lady who only drove to grocery store. But she was there and back home before everyone rolled out of bed..
@michaelarndt1961 Жыл бұрын
Car is a beast it idles to fast but it is badass God bless you guys
@ic90494 жыл бұрын
Lmao definitely a big BOOM if he’s in a head on accident
@JesusRoman4 жыл бұрын
Hello, my name is Jesus, and manage a fanpage on Facebook called "Chevy fans". I've seen your video and I'd like to share it. I'm asking for your permission since I'wouldn't like to violate the copyright on it. Hope you let me share it. Thank you in advance!
@garydickson10374 жыл бұрын
do Not deserve that car
@jimpenman8064 жыл бұрын
Have
@tylerbonser76863 жыл бұрын
I will never understand why people post videos of them sucking at doing something.
@Nick-dz4ml
2 жыл бұрын
Not everyone is a professional so why care
@muzzy13465 жыл бұрын
I cringed... haha
@pmd7771969 Жыл бұрын
Cool. Bloodviking
@nitromethane22284 жыл бұрын
Maybe you should take lessons on how to start that thing
@jaydenstoddard6099
3 жыл бұрын
He knows how to start it he hasn't ran it in so long it was his first time starting it in a long time and its been re built its a race car kid
@JeffEngstrom015 жыл бұрын
lol rookies
@funone87163 жыл бұрын
He doesn't know there's no accelerator pump on his engine.....LOL. And squirt bottle dude does not know how thirsty it is. They look silly.
@patrickmckeever23784 жыл бұрын
😨😲😱😰
@TheUnholyPosole5 жыл бұрын
...reminds me of my sex drive.
@wesleybowles53772 жыл бұрын
Timing sounds too high
@jarosdav4 жыл бұрын
bunch of rookies! and that chases looks pretty suspect the way its built
@welldonempofuu9842
4 жыл бұрын
Hater
@dirtydeedzmainecultavator683 жыл бұрын
not all that smart revin a cold motor!😳
@nalley6815
Жыл бұрын
It’s a race engine lmfao
@dirtydeedzmainecultavator68
Жыл бұрын
@@nalley6815 ok....
@poncoolride4 жыл бұрын
Quit pumping the throttle! It injected not carbed! Also, if you keep piss winding it before its warm like that your bearings are going to go south pretty quickly. And you will scoff the shit out of the pistons. Really, you should have hired a blown alcohol crew chief or someone knowledgeable to show you the ropes before you started this project. As old as this video is im guessing you have probably figured it out be now, maybe the hard way.
@prostreetgsxr Жыл бұрын
This video shows if you have the money, you can have a nice toy even if you don’t know what you are doing. Keep pumping the gas pedal as if you are working with carburetors with accelerator pump’s 😂😂😂
@johnb55122 жыл бұрын
Who ever recorded this the sound is real bad
@user-jg6wx3lh1x6 жыл бұрын
Lame
@rbsrazor6001
6 жыл бұрын
I feel sorry for that motor, what an idiot
@jaydenstoddard6099
5 жыл бұрын
Look at ur channel. LAME
@popiwatv5 жыл бұрын
Junk. Can't even start on it's on
@jaydenstoddard6099
5 жыл бұрын
It hasn't been ran for a wile dumb dumb
@ryan14r95
5 жыл бұрын
sctflasher379 dumbass you have to put fuel in it to get it started plus it’s probably better than your moms minivan
@kennethburrell9317
4 жыл бұрын
i guess all the TF & FC are junk too? 3-4 sec quarter mile engines are a long way from Junk
@lucasdorabiallo97793 жыл бұрын
the fuel tank is very close to the engine .... very low fuel pressure so it is turning off the engine so much, basic thing .... you are crazy to put the fuel tank like this in front of the engine 🤷🏻♂️ 🤷🏻♂️🤔🤔🤦🏻♂️
@tylerbonser7686
3 жыл бұрын
Why would having the "fuel cell" close to the engine cause low pressure? Also it is common and even pretty standard to have it located there. Plus the g forces actually push the fuel to the engine instead of away.
@markg1495
3 жыл бұрын
That’s called a D R A G C A R
@NRJracing10 ай бұрын
Yea you can certainly tell that nobody anywhere near this car actually built the engine otherwise you would have more sense that to stomp the throttle until the valves float out DEAD COLD. They can’t even keep this thing in time let alone build an engine. IT NEEDS TIMING
Пікірлер: 137
Watching them it was the most painful experience
Money can’t buy you brains!
@rallydogmakes3861
3 жыл бұрын
?
@seabasschukwu6988
3 жыл бұрын
@@rallydogmakes3861 they were pumping the throttle... you don’t do that on a blown motor. It’s a big no no
Watched the video :( and went right to the comment section.... must say did not disappoint
Excellent way to spin a bearing, fire up a cold engine, and go to whopping the throttle like that...This is why we can't have nice things.
@FIVE-0-APOCALYPTO
3 жыл бұрын
24 likes on your statement. Let's assume the build is done correct. I used to race. I also was part of a team. We had a good crew chief, he also built the motors. Very knowledgeable guy. We would run 15/1 C-16 fuel type motors. Callie's dragon Slayer, AFR, scorpion....good stuff. Crew chief: "The last thing I'm worried about, is that motor blowing up. It's bullet proof". A fresh build, one test on the Dyno, these engines are ready to go. Set the Rev limiter a couple hundred rpm short of the upper end starting to get unhappy and run that motor as hard as you want. There is no break in. The cylinder walls will warp oval before you spin a bearing. LONG before you ever spin a bearing. In fact, you will break something like a rod or something before spinning a bearing. And if something does break, even the crank shaft, it's almost ALWAYS because of something else. This isn't eldebrock, factory cast iron loose tolerance bullshit. This is high dollar, close tolerance, over kill metallurgy and specs. If there is important aspects that need heat or heat sink, it is designed to happen quick. It's not a issue. Not with these type of builds. When you race, it's not like you always have time to prep perfectly. Sometimes, you get rushed to the line. You fire it up, check your guages, get your slicks hot, hit the line, stage, hit the tranny brake, stomp the throttle, focus everything you got on the dying second amber and let the fucker go. Warm or a little cold, that motor will not give a fuck. It's built to go. It's not delicate. In fact, babying it would be risking a problem. Anyway, I don't see how you get 24 likes on a statement like that, unless y'all are just spectators. These engines, are bad ass. But it's not self destructive like top fuel. You race for a day or weekend, change the oil, run your inspections, make any adjustments or tweaks needed and it's ready for another weekend of pounding the throttle and the motor is very happy. That's the truth. What you said, is not true.
@welldonempofuu9842
3 жыл бұрын
@@FIVE-0-APOCALYPTO amen brother
@tylerbonser7686
3 жыл бұрын
@@FIVE-0-APOCALYPTO warming up a motor isn't considered babying it. While spinning a bearing would be one of my last concerns on a cold motor, revving the piss out of one is just stupid. It's not like you need to warm the engine up for 10 minutes right before you race but it is important to heat soak it before racing begins.
@nalley6815
Жыл бұрын
@@tylerbonser7686 um no. Heat soaked makes you run a lot slower lol
@tylerbonser7686
Жыл бұрын
@@nalley6815 then why exactly does every drag racer do it?
your project is really cool, here in Brazil we have a lot of difficulty with the cost of the parts but we also have very strong cars ... our specialty is the turbo 🇧🇷🇧🇷🇧🇷
@SAtinnBlack
2 жыл бұрын
Sounds very interesting what’s the car scene like there?
@TT-di6qk
2 жыл бұрын
brazil sucks
Put some gas in your jug you use to prime it. And don't be scared to dump a lot of fuel in it when your priming it. Also keep putting it in until the pump gets it going. You will here it.
@user-jg6wx3lh1x
6 жыл бұрын
Fucktard, why would you use gas to light an alcohol motor?
@bryanswift8583
5 жыл бұрын
Hahaha Jesus Steve g is the man
@cardboardboxification
5 жыл бұрын
Steve G. Look up the enthalpy of the fuel goof
@N2Otorious
5 жыл бұрын
+Steve G. Hey bud I could figure out how to send you a private message, Man I'd love to chat with you and ask some questions. I have an 8-71 on a Big Block with an Enderle Big&Ugly... I'll have my engine back together soon and would like to ask you some questions that your experience might help me get this thing sorted faster. www.dropbox.com/s/pbvz7o0ryy0xg66/20180720_142939.jpg?dl=0
@andrewaharvey
5 жыл бұрын
Steve G. Have any spares your looking to unload
what a spectacular project 👏🏻
YEAH BLOWN-UP !!
Bout time.... GEEZ. Nice build. Thumbs up
Stay off the throttle. You're leaning it out. The guy on the bottle should be in control of the fuel.
@darkkinggaming7988
4 жыл бұрын
Exactly
The guy with the bottle is supposed to keep squirting or as they say bottle feeding the blower until the fuel pump can catch up and take over. One or two squirts ain't going to get unless the fuel system is really well thought out. Great car & video 👍
He's pumping the throttle like a carb. Obviously he knows jack chit about engines.
@michaelmcneil5036
4 жыл бұрын
You don't pump a carb when rolling it over either
@konnerkramer329
4 жыл бұрын
@@michaelmcneil5036 why don't you pump are carb while cranking?
@michaelmcneil5036
4 жыл бұрын
@@konnerkramer329 I was just thought to pump before you start cranking because of too much fuel dumping into the carb
@sandstonefarm5722
4 жыл бұрын
@@michaelmcneil5036 yuup 3 pumps then fire it up also need to let it warm up befor you hammer on it too
@0hjaa3.06
3 жыл бұрын
@@sandstonefarm5722 No need. Pull the choke close and then start it. No pumping required. Otherwise is just dumps raw fuel out the pipe just for shits and giggles
The revs sound like thunder strikes
I love it
I get a kick out of pumping the gas on mechanical fuel injection
Let’s go racing!
haha hes used to burn soy sauce in his little honda .... also steve g. dont forget to shut fuel off before ignition so you dont wash down your cylinders and bend a rod
I remember when I had my first beer.
@compoundlml7156
3 жыл бұрын
Hahahaha that's so funny the last time I heard that I fell of my dinosaur -Dale Doback
@centermass4962
2 жыл бұрын
Would u care for some fancy sauce?
Is that you toad in that beautiful car
Must not be a big fan of letting stuff warm up before you spin it 8000 rpm with no load on it.
@steven8075
2 жыл бұрын
builds of that caliber have oil warmers. motors like that can even lock up when cold so they have to be at temp before you can even try to start them. so yeah it's not a problem to start them up and rev them to the moon.
@Robertm6996
2 жыл бұрын
Thanks for the information. I had no idea👍
Why is he pumping tha goddamed throttle!? Dont do that on a blown injected motor!
@HyperKid36
5 жыл бұрын
never, never pump the throttle when priming a mechanically injected engine. big no no !
@nikolas812
5 жыл бұрын
Most of the people replying to this video have more knowledge than the guy that posted the video. I feel sorry for thst motor...
@chrisstuffel6819
Жыл бұрын
Testing the strength of the blower straps
A lot of experts in the comments here...
How expensive is this blown Alcohol race engine?
Wow.
can you remove the first minute and a half?
Exactly
👍🏼
Why?
She didn't want to prime up.
me in no limit racing
That took forever....
I think the diesel fuel has got water in it. My kubota does the same thing.
@adolphsfather4834
3 жыл бұрын
That isn't a diesel
Bought from some old lady who only drove to grocery store. But she was there and back home before everyone rolled out of bed..
Car is a beast it idles to fast but it is badass God bless you guys
Lmao definitely a big BOOM if he’s in a head on accident
Hello, my name is Jesus, and manage a fanpage on Facebook called "Chevy fans". I've seen your video and I'd like to share it. I'm asking for your permission since I'wouldn't like to violate the copyright on it. Hope you let me share it. Thank you in advance!
do Not deserve that car
Have
I will never understand why people post videos of them sucking at doing something.
@Nick-dz4ml
2 жыл бұрын
Not everyone is a professional so why care
I cringed... haha
Cool. Bloodviking
Maybe you should take lessons on how to start that thing
@jaydenstoddard6099
3 жыл бұрын
He knows how to start it he hasn't ran it in so long it was his first time starting it in a long time and its been re built its a race car kid
lol rookies
He doesn't know there's no accelerator pump on his engine.....LOL. And squirt bottle dude does not know how thirsty it is. They look silly.
😨😲😱😰
...reminds me of my sex drive.
Timing sounds too high
bunch of rookies! and that chases looks pretty suspect the way its built
@welldonempofuu9842
4 жыл бұрын
Hater
not all that smart revin a cold motor!😳
@nalley6815
Жыл бұрын
It’s a race engine lmfao
@dirtydeedzmainecultavator68
Жыл бұрын
@@nalley6815 ok....
Quit pumping the throttle! It injected not carbed! Also, if you keep piss winding it before its warm like that your bearings are going to go south pretty quickly. And you will scoff the shit out of the pistons. Really, you should have hired a blown alcohol crew chief or someone knowledgeable to show you the ropes before you started this project. As old as this video is im guessing you have probably figured it out be now, maybe the hard way.
This video shows if you have the money, you can have a nice toy even if you don’t know what you are doing. Keep pumping the gas pedal as if you are working with carburetors with accelerator pump’s 😂😂😂
Who ever recorded this the sound is real bad
Lame
@rbsrazor6001
6 жыл бұрын
I feel sorry for that motor, what an idiot
@jaydenstoddard6099
5 жыл бұрын
Look at ur channel. LAME
Junk. Can't even start on it's on
@jaydenstoddard6099
5 жыл бұрын
It hasn't been ran for a wile dumb dumb
@ryan14r95
5 жыл бұрын
sctflasher379 dumbass you have to put fuel in it to get it started plus it’s probably better than your moms minivan
@kennethburrell9317
4 жыл бұрын
i guess all the TF & FC are junk too? 3-4 sec quarter mile engines are a long way from Junk
the fuel tank is very close to the engine .... very low fuel pressure so it is turning off the engine so much, basic thing .... you are crazy to put the fuel tank like this in front of the engine 🤷🏻♂️ 🤷🏻♂️🤔🤔🤦🏻♂️
@tylerbonser7686
3 жыл бұрын
Why would having the "fuel cell" close to the engine cause low pressure? Also it is common and even pretty standard to have it located there. Plus the g forces actually push the fuel to the engine instead of away.
@markg1495
3 жыл бұрын
That’s called a D R A G C A R
Yea you can certainly tell that nobody anywhere near this car actually built the engine otherwise you would have more sense that to stomp the throttle until the valves float out DEAD COLD. They can’t even keep this thing in time let alone build an engine. IT NEEDS TIMING