Again something learned about the Flysky Transmitter. Thank you!

@WTFRCCars

2 жыл бұрын

I have just got done testing a theta razor T1 1000hz servo and that one works full 1000hz on both nb4 and pro :)

I'm looking for a servo I can program for 6 rotation and standat size and high speed and torque. Any recommendation? Would like to program the 9imond line servo to more rotation numbers

@WTFRCCars

Ай бұрын

I don't know of any servos that allow you to program them this way at all

Hey WTF , just wondering why I don't have the AUX app on my NP4 Pro transmitter , the current firmware on it is 1.0.5 std. Is there a latest version on the firmware other than what I indicated?

@WTFRCCars

5 ай бұрын

If it's a pro then it's had the option from the 1st firmware

My agfrc servo worked with my flysky when I hooked it up to test it. Later when I did final assembly and looked it up, nothing. Too bad the website don't have a signal trigger to test with. At least none that I've seen

@WTFRCCars

Ай бұрын

There ain't much that will stop a servo working with a radio, few things to check 1st is the plug is in the right way, next check the cable for damage, make sure the transmitter is set to the correct servo frequency, check that the bec is set to the right voltage, but there's no reason for a servo to just not work when it did before

@TheOldKid

Ай бұрын

@WTFRCCars appreciate it. Yeah I went round and round checking and checking again. Voltage, plug direction, freq and even tried various freq. I dug around looking for a potentiometer but have misplaced it. Any idea the signal voltage? If I put 6v - 8v to power leads and put a small voltage to the signal would or should I get a response? I haven't tried it yet. I think my project just has gremlins since everytime I go to do a final assembly something else happens. This is the third time to put it on the back burner and move on for awhile. Last time I used a l293d for two other motors and all five motors did great except my motor for the carousel wasn't big enough. I swapped that motor with a powerwheels grave digger motor and once I turned everything on it was great until a main voltage wire came loose and shorted setting the l293d on fire. To the back burner she went. After replacing the electronics and ordering the new servo I tested all motors and once again all was well until it wasn't. I'll order a couple more servos but my curiosity on this one is driving me nuts

@WTFRCCars

Ай бұрын

@TheOldKid don't put voltage to the signal wire it's a digital pwm signal not variable voltage that tells the servo to move :)

@TheOldKid

Ай бұрын

@WTFRCCars I loaded the "myservo" from aruino ide and tested 3 servos. The agf was only one that didn't work. I guess it's possible I just got a lemon. Not a big deal. I'm sure they're good servos and normally don't have issues. I'll order another. Thanks

@WTFRCCars

Ай бұрын

@TheOldKid AGFRC are programmable so if it's set to say 833hz or 1000hz it won't work on a stock servo tester as it needs the correct signal

Question. I purchased this brand servo to put in an aerobatic plane. If I move the control quickly they center fine. Slow movement they stop short of center. I have the programmer in the mail. Will one of those settings adjust the servo sensitivity in center to get rid of the dead spot? Thank you

@WTFRCCars

Жыл бұрын

You can adjust lots in the software but what transmitter you running ? Asking as I race with these and never have an issue with centering so wondering if you have the correct servo frequency/refresh rate set?

@alwaysflying6540

Жыл бұрын

@WTF RC Cars I am using Spektrum Equipment running the Dx9 TX for digital servos 22ms. Powering the servos at 6v regulated

@alwaysflying6540

Жыл бұрын

@WTF RC Cars I was wondering about servo frequency as well. If I can change that with the programmer it might do the trick

@WTFRCCars

Жыл бұрын

Yes you can change the servo frequency with the software you can also change the centre dead band I believe. On the spectrum tx can you change the servo refresh frequency like I do on the flysky nb4/pro I can set it anywhere from 60hz to 1000hz ?

@alwaysflying6540

Жыл бұрын

@WTF RC Cars I will look into the refresh. I did not know I could do that with my Tx. I was at a loss with this problem and was hoping that the programmer would allow me to change these parameters. The servos are quiet smooth and fast, they just can't find the center every time. I'm very excited for the programmer to show in the mail. Thank you so much for your help.

So did you leave it in the stock setting for use on the FLysky NB4?

@WTFRCCars

Жыл бұрын

No I have it running none 360 and sfr highest hz mode I believe

do you know how to make the a20 cls rotate 180 degree?

@WTFRCCars

Жыл бұрын

Yes you need a transmitter that can output a signal from 500 to 2500us and you may need the AGF-SPV3 Servo Programmer to set it up on the servo but as stock it should be set to full travel so I'd guess your transmitter can't do the full 180° is the most likely issue :)

can you set more then 1 throttle point and set different speeds between each set point?

@WTFRCCars

2 жыл бұрын

I'll have to take a look for you :)

@mally_mal820

2 жыл бұрын

@@WTFRCCars that would be great. maybe do a video on it if its possible. I just searched and haven't found the answer..

Did you ever figure out what the damping setting does ?

@WTFRCCars

Жыл бұрын

I did ask and was told like a softening effect for when it starts and stops moving

Do they work with Apple computer?

@WTFRCCars

3 ай бұрын

Nope only windows as far as I can tell