Awesome job Drew, glad you you’re back with some videos.

Good work. I need to do that timing trick on my 2511.

Very nice work bud, seems a little more snappy!

Great job buddy! Have a great weekend! 👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏

@drewscreations8551

2 жыл бұрын

You too!

Nice freakin job there. Snappy heck yea. !!🦾❤️‍🔥☀️

@drewscreations8551

2 жыл бұрын

Thank you!

Snappy and happy!! 😂 great job buddy!!

@drewscreations8551

2 жыл бұрын

Lol I like that! Thank you pal! Need to hangout soon! 😂

@grayclapp1081

2 жыл бұрын

@@drewscreations8551 yea we do brother!! Been busy down here lately.

@drewscreations8551

2 жыл бұрын

@@grayclapp1081 same here

I did the West Coast muffler mod and the maximum rpm is now 15,500 at wide open throttle. Really improved throttle response and horsepower.😮🤯🐴🔋⛓️🪚🪵

I was hoping to see how she cuts now after the mods. Cool video! 😎😎

@drewscreations8551

Ай бұрын

Got a video of it cutting

@drewscreations8551

Ай бұрын

kzread.info/dash/bejne/iaF72JSqfMTFidY.htmlsi=8yjdiecOo7TinMMe

@williamgrissom1995

Ай бұрын

​@@drewscreations8551lol I went looking and found it before seeing your reply. She really digs in now. I use to have 2 of those and it would have been awesome to have had them perform that great, though I had no complaint with them anyway. I miss those saws. Very cool. 😎👍

@drewscreations8551

Ай бұрын

@@williamgrissom1995 they’re a great saw! I have a rear handle model I run now that is much better for use on the ground. Same saw but better feel lol.

@williamgrissom1995

Ай бұрын

@@drewscreations8551 awesome. I never tried the rear handle version. I generally used my ms261 if I felt I needed a rear handle and a Ms361 with a 25 inch bar with a skip tooth chain for the larger stuff. The MS200T and the Ms361 saws were my favorite goto saws. I did like the ms009. It was slower but with plenty of torque. I gave my brother a ms170 and a farm boss. I think it was the Stihl MS290. Needless to say I am a Stihl fan. Lol

What you are advancing here if stock ignition timing in 200t is already on 32 degrees which is max you can advance, good luck with that…

How much do you file off the key before its too much? I changed the cluch drum over to run a micro p chain on my 200t planning to do timing and exhaust maybe a wee port bothering if i dare ! Thanks for video be curious to know how much to go before i start ! Cheers

@drewscreations8551

2 жыл бұрын

Usually 1/4-1/2 the key is what I do

hi drew,your a great mechanic ! carb replacement becomes a nightmare after several trys .. intake boot keep deforming during installation on 200t stihl.. can you please help me...tom

@drewscreations8551

2 ай бұрын

Thanks buddy! I appreciate it! Are you having issues getting the boot on the actually cylinder, or is it when you go to put the handle on?

Hi Andrew!!😀😀 Good to see you buddy!!😀😀 Nice job on the saw. The muffler mod really made a big difference in power all by it's self. Now if it was ported it would really scream. Take care my friend!!😀😀

@drewscreations8551

2 жыл бұрын

200s don’t really gain much from porting. I’ve done a few and they don’t run much different

john's custom saws I believe mentioned you lose power when you advance the timing on these.... any thoughts? thanks for sharing

@drewscreations8551

Жыл бұрын

I don’t think you necessarily loose power unless you go too far. You can loose some torque by advancing timing because usually timing is associated with RPM. I don’t really port 200s because I feel like there isn’t much there to gain. Joe harkness has a chainsaw dyno and he ported one and machined the chamber and base and when it was done, it showed an 8% gain on the dyno. With most saws you get 10-20% and most of the time more along the lines of 15-20 when done properly. This is all just hypothetical though because there are a million factors that affect all this. Hope this helps

@jbbolts

Жыл бұрын

@@drewscreations8551 definitely agree ...on the million factors point... tinman says the same thing... same numbers will yield very different results from one porter to another not to mention every saw is different also

@drewscreations8551

Жыл бұрын

definitely

I’m the guy that puts an oversized screw in a saw if it strips out😆

@drewscreations8551

2 жыл бұрын

Your evil sir!

How did you unscrew that without something holding the other nut on the other side???

@drewscreations8551

Күн бұрын

What are you referring to? The flywheel?

When I work on a saw I have to swear and throw things or something or it won’t come out right.

@drewscreations8551

5 ай бұрын

It’s like that sometimes lol

Let me send mine to you bud

@drewscreations8551

Жыл бұрын

You have a 200t you want done?

@nicolasadams6431

Жыл бұрын

@@drewscreations8551 020t I could do it myself but don't really have enough time constantly working let me know if you pour and polish as well

@drewscreations8551

Жыл бұрын

@@nicolasadams6431 I do port work, but I don’t port 200t saws. I’ll do the timing advance and muffler mod though

Thems mean little saws....my farmertec clone is a beast🤙🏻🪓😎..nice work buddy

@drewscreations8551

2 жыл бұрын

Thanks! Yeah they are!