1st time Traxxas E-Revo player here. Thanks for the help.

Thank you for your demonstration. That really helped. I could not get it right until I saw your video🤩

KING 🤴🏻 Thank you !

Great vids man. Loving yr work. Subbed

This video really help ! Thank you !

I’m new to these and just got 2 of them given to me and this video helped tremendously. Thank you so much

@upgradedrc3697

Жыл бұрын

You are very welcome. Let me know if you have any questions.😎👍🤙

Dam utube is the best teacher ! Thanks man

Awesome video thanks

This video really helps 👍🏻

You explained this topic very well thanks

Thanks man I appreciate it

I use the stock plastic spur gear. Cause if something on the drivetrain is going to break, I want it to be my spur gear. It's only $3.00, and it's easy to replace!👍

@DizzyDsvids2Please

3 жыл бұрын

Same here!!!!

@timprice8877

2 жыл бұрын

Metal is only $7 lmao not really a big deal

@jimferry4751

2 жыл бұрын

Do you have a video on how to replace the spur. Mine stripped after 3 months. I ordered the metal version. Should I just replace with the stock plastic one?

@upgradedrc3697

2 жыл бұрын

Yes, definitely do not get a metal gear, stick with plastic cause something has to be the weak link. Mise well be a $3.00 gear that is easy to replace. I have a video on the differentials wich includes the clutch and spur gear assembly.

@upgradedrc3697

2 жыл бұрын

I think it's in this one lol! kzread.info/dash/bejne/pa5n0rqrhKqqlNI.html

Thanks man subbed

thank you so much!

On the E-Revo 2.0 VXL the motor mount creates a tighter mesh between the pinion and spur gear as you are tightening the upper motor mount bolt. That said, I preemptively account for this and intentionally give it a looser mesh and when I tighten the motor mount screw it gives it a perfect mesh.

Thx bro

There is no need to loosen the bottom screw on the motor mount. The motor mount pivots on a plastic peg, that screw is holding that peg in place. Just loosen the top screw and you can adjust the mesh.

@noobflyer1

3 жыл бұрын

i was thinking the same thing, but could not remember for sure

@winstonoso5821

3 жыл бұрын

Do u know how to mesh on a kaiju? Not really sure how to don iui t.

👍

Hey Trev, After fooling around with the cranky old conversion transmission, I want to install a center diff instead. What will I need and have you done a video on it thanks. This is in the E Revo conversion.

@upgradedrc3697

3 жыл бұрын

This video is the closest thing i have that would help you out seeing what your going to need. Sorry, I have never done a conversion before, but i am sure there are Traxxas forums where people have done this. hopfuly this video will help u out some. kzread.info/dash/bejne/gqN3qJOPeaStmrg.html

love the video, i have an e revo 2.0 vxl as well, i want to use a 14 tooth pinion gear, do you happen to know if i need to move the motor from the low CG mounting holes to the high CG mounting holes? According to the manual page 27 it looks like they want you to, but if i remove the 3 hole plastic piece i would think i could adjust it just like you did. I really don't want to have to raise my motor to the higher CG holes

@upgradedrc3697

3 жыл бұрын

You probably will have to use the C position for the 14. But, I know a lot of people who have just gotten rid of the plastic adaptor and adjusted it correctly without it, just make sure it is tight with Loctite and get the mesh right!

@noobflyer1

3 жыл бұрын

@@upgradedrc3697 Thanks for the info !!!!

Thanks for the videos, I just got a e revo conversion , I am having a hard time getting the dx5c and the 6 ch rx to deal with the 2 speed trany and reverse. Can you help the some tips on how to make this work...thanks

@upgradedrc3697

3 жыл бұрын

The E Revo does not have a 2 speed trany or any trany. Just a center diff with a tork basing gear. What are you trying to do with the dx5c?

@budnanc509

3 жыл бұрын

@@upgradedrc3697 This is from a nitro conversion I am told. I was told it had a 2 Speed with reverse. I am not sure how I can give you a better image of the truck. It supposed to be 1/10 scale. I can see a servo move in the trany and sounds like it has 2 speeds, have not been able to ingage the rev servo. From what I read, the 2 speed should cintriphical , and reverse should be another servo operation.

@budnanc509

3 жыл бұрын

Ok trav, I got the servo to the rev gear set to a switch, functions, the long servo which I thinks is for the brake and 2 speed does not move. I have the rev gear in #4 on the rx and #3 for the brake 2 speed. Dont seemed to have movement on #3. Is there another setting I am missing? When I bind the 6100 rx It reacts like the throttle when pushed up in normal rev should be now brake. Confuseing.

@budnanc509

3 жыл бұрын

I have the speed and brake servo adjusted to a point where the revo has forward with little brake. This does not operate like a drag brake in crawling or is the revo supposed to run free wheeling? Or is there a way to break via the esc?

@upgradedrc3697

3 жыл бұрын

@@budnanc509 So on the E Revo 2.0 , It free wheels and you use rev for the brakes. On yours I believe your brake servo stops you, but I really don't have much experience with the Nitro setup or your conversion. But there are a lot end points that need to be set on all the servos and adjusted on the servo horn, arm, or shaft first, then adjust all end points on radio, then adjust the trims. I wish I could be there, it's hard for me to give this kind of advice when I can't see how it is suppose to work and if anything is out of adj or not.

Hello there is it better to change the spur gear to the metal one ?

@upgradedrc3697

3 жыл бұрын

No metal gears are bad. They last longer, but if the nylon gear dosen't break first, then it ruins the other gears down the line. The spur is the easiest one to change and the cheapest. So you want that to take all the abuse and save the other harder to get gears. Metal gears are bad.

Hey man does the 20t and 46t work with the adapter

@prestonjames6776

Жыл бұрын

Yes, you'll just have to change the orientation from the motor to motor mount holes. There are 3 sets of holes, 2 of which are used for the original motor with small or large pinion and the last set of holes used for Large Motors.

Can you please tell me what combination using there

@upgradedrc3697

5 жыл бұрын

I am running 16/46

@anilrc914

5 жыл бұрын

Good morning man sorry to bother you can you please tell me which pinion gear can work with the 46 tooth spur gear in DOS tree motor mount hole

@upgradedrc3697

5 жыл бұрын

I am running a 16t pinion and a 46t spur gear, and I am using the adapter with my bolt in the center position. This combination works great for me bashing and jumping and general all around!

Is the pinion gear suppose to move up and down or is it suppose to be locked into place with the spur gear

@upgradedrc3697

3 жыл бұрын

Definitely should be tight aginst the spur with only enough room to get the papper out.

@JBK-w5u

3 жыл бұрын

@@upgradedrc3697 when I give my car throttle the pinion gear stays in contact with my spur but it goes up and down so sliding. I didn’t know if it had to stay in one spot. But What can I do to fix it

@upgradedrc3697

3 жыл бұрын

@@JBK-w5u Is the motor plate tight to the motor and are you useing the correct holes for the pinyon you are using?

@upgradedrc3697

3 жыл бұрын

I just started up a group called Upgraded RC Bashers bashers crasher and crawlers. here is the link it will be easier to help you there facebook.com/groups/2812810532319871

@JBK-w5u

3 жыл бұрын

@@upgradedrc3697 Yes, I’m using all the right screws but I forgot I had to tighten the pinion gear itself but I think I fixed it

How do you set the gear mesh on a 4 x 4

@upgradedrc3697

4 жыл бұрын

I'm don't know which one you are referring to, but most 4x4s are the same.

@winstonoso5821

3 жыл бұрын

How bout on a kaiju? Mesh setting.?

Never seen anyone fold the paper in 2. Wouldn’t that make it to loose?

@upgradedrc3697

4 жыл бұрын

Worked out great for me. A lot of abuse for a long time and still running the same gears.

@KTMcaptain

3 жыл бұрын

I saw your comment a while back and wanted to just say an experience I had today. . I too use a double folded paper. I never felt a single piece was enough, so have just always went with a double. Last night I threw on a 50t spur with my 12t pinion to see how I like it, but only used a single piece of paper. . After about 10 minutes of running it I started hearing a sound the was similar to a bearing running dry. Anything above 30,000 rpm and it would make this noise. . So I reset my mesh to a double piece and voilà the sound is gone. . Using the preset mesh adapter I can tell it’s a little looser than a double sheet, so you’ll be fine.

@ajgreen868

3 жыл бұрын

Firestarter I to have been using the double folded paper since I seen this. I have to say it works like a charm!

I'm not sure . Use what u want to, it is not necessary to use the adapter. Just make sure the mesh is correct and tighten up the bolt real good.

My pinin gear will not fit in the center of the spur gear. It doesn't have enough room

@upgradedrc3697

3 жыл бұрын

What Pinyon and Spur are you running?

@andimthedumdone

3 жыл бұрын

@@upgradedrc3697 I have the stock pinion gear and just the upgraded spur gear that's metal

@upgradedrc3697

3 жыл бұрын

Is your motor plate on correctly?

@andimthedumdone

3 жыл бұрын

@@upgradedrc3697 probably not I couldn't find a video on how to put it on the way it came stock after I got a new motor

@upgradedrc3697

3 жыл бұрын

Adjust the motor plate so that the pinyon shaft is pretty much lined up in the center of the motor plate.then use the appropriate hole in the motor mount for the size pinyon that u have and follow the video for the correct gear mesh

My motor mounts came loose 1 week after owning mine anyone else had that happen? It’s super easy to fix just weird it happened so fast only driven the car 3 times.

@upgradedrc3697

3 жыл бұрын

Mine came loose on the 3rd or fourth time as well. use loctite and check it regularly as well as the pinyon. it will eat the sour gear up if it comes loose.

@UnhingedCanadian

3 жыл бұрын

@@upgradedrc3697 will do

Ok cool

No

What is the biggest spur l can use will the 46t and the adapter

That is the metal spur gear you using or the plastic

Can you tell me every screw that I should log tight

@upgradedrc3697

3 жыл бұрын

Only the pinyon socket screw on the motor shaft needs loc tite. The two that hold on the motor do no need loc tite , just tighten them up.

@Alphabet7

3 жыл бұрын

@@upgradedrc3697 u should make a KZread video showing every screw on the car that you put loctite on But thank you I will do that now your video was very very helpful

I hope by now you bought some real tools