This video is from this spring. I show you how my adjustable bending jig works.
Жүктеу.....
Пікірлер: 43
@luisalarcon70607 ай бұрын
Gracias amigo muy buena me va a servir muchísimo saludos desde alerce región de los lagos puerto montt
@aaronmccann32462 жыл бұрын
Simple and functional; thanks for sharing!
@stevenlarsen16912 жыл бұрын
With mine, I use a 1/2" square bar so it fits my sockets. I like yours. I will try it. Thank you!
@szermierz77983 жыл бұрын
Such a simple yet useful device. When I think that so far I have bent the wires with a hammer on the anvil ... Tomorrow I'm going to create this little helper. Thank you for sharing your knowledge.
@forestdragonworkshop7613
3 жыл бұрын
You're welcome. Jig helps to make repetitive items in a short time. On the other hand, being able to do the same on the anvil is also important.
@AyoubAyoub-qu5eo
2 жыл бұрын
@@forestdragonworkshop7613 w
@mattthescreamer1773 жыл бұрын
Thanks you so much for this design. I started researching bending jigs today and yours is one of the best I've found on KZread. Great work and keep posting, thanks again.
@forestdragonworkshop7613
3 жыл бұрын
I'm glad the video was helpful. I will finish building a new workshop soon. Then new videos should appear.
@oniironworks49203 жыл бұрын
Cool little jig! Nice work!
@forestdragonworkshop7613
3 жыл бұрын
Thank you very much.
@nerisdf2 жыл бұрын
very good job
@arturomora98072 жыл бұрын
Good job my friend 🤪👍
@RajuN2 жыл бұрын
Perfect n Super. 👍👍👍
@sachinpanchal81902 жыл бұрын
Very good idea sir 🙏👌🌹❤🚩🇮🇳
@MG-gs4uu2 жыл бұрын
Súper 👌🙏
@kreasiumum2 жыл бұрын
Sudah punya alat ini, namun baru tahu cara menggunakannya setelah melihat vidio ini, terimakasih.
@forestdragonworkshop7613
2 жыл бұрын
You're welcome
@fernandorodriguezmaya39972 жыл бұрын
BUENÍSIMO
@pandharinathkhairnar98932 жыл бұрын
Good
@vicentefernandez39302 жыл бұрын
Un buen forjador lo hace sobre el yunque.
@forestdragonworkshop7613
2 жыл бұрын
Yes, you are right, but this way it was easier and faster for me to make repetitive large amounts of rings.
@arturdesouza592 жыл бұрын
👏👏👏👏👏👏👏👏
@charliebecker22162 жыл бұрын
Nice basic system . U could probably put larger pipe and make larger diameter rings.
@forestdragonworkshop7613
2 жыл бұрын
It was the size I needed most often and in large quantity. I made single pieces of other sizes by hand on the anvil.
@MrAmaref2 жыл бұрын
خیلی جالب بود ای کاش روش ساخت خود دستگاه رو هم قرتر بدهید
@forestdragonworkshop7613
2 жыл бұрын
It was a prototype and it worked well.
@creativity17602 жыл бұрын
👍
@franciscoribeirotorres9943
2 жыл бұрын
Nu p8
@prithvirajgayalkar26672 жыл бұрын
What about bigger circumference.
@forestdragonworkshop7613
2 жыл бұрын
I do them by hand on the anvil or use a piece of pipe for it.
@user-if9zg1vd1x2 жыл бұрын
А для чего?
@geraldabierta13032 жыл бұрын
Maga adjustable straps
@user-kt6rh6jh6u2 жыл бұрын
ВСЁ СУПЕР,ТОЛЬКО ВОТ В КАКОЙ КОМНАТЕ НА ВОСЬМОМ ЭТАЖЕ ПОСТАВИТЬ ГОРН.🤨🤨🤨
@user-ft4zk1jc1n
2 жыл бұрын
А горн и не нужен достаточно в зале поставить верстак, наковальню и ИНДУКТОР и пожалуйста изготавливайте крючки и прочие скобяные изделия...
@forestdragonworkshop7613
2 жыл бұрын
Maybe an induction heater would be a solution. Only they are a bit expensive.
@mdmohammed47852 жыл бұрын
مادام في وجود ملزمه تثبت الحديد فليس داعي لكل هذه الشغلات انظر ماسوره حديد وقظيب حديد وثبتها بالملزمه واشتقل وانتهت الموضوع
@forestdragonworkshop7613
2 жыл бұрын
It can be done as you say. But I did one jig for different rod thicknesses.
@fernandohernandezn.57632 жыл бұрын
NO GUSTA , SÍ LO HICIERAS AL FRIO, 10/10, PERO ASÍ YO TE PONGO UN 5/10.
@forestdragonworkshop7613
2 жыл бұрын
It's faster for me to do this when the metal is hot.
Пікірлер: 43
Gracias amigo muy buena me va a servir muchísimo saludos desde alerce región de los lagos puerto montt
Simple and functional; thanks for sharing!
With mine, I use a 1/2" square bar so it fits my sockets. I like yours. I will try it. Thank you!
Such a simple yet useful device. When I think that so far I have bent the wires with a hammer on the anvil ... Tomorrow I'm going to create this little helper. Thank you for sharing your knowledge.
@forestdragonworkshop7613
3 жыл бұрын
You're welcome. Jig helps to make repetitive items in a short time. On the other hand, being able to do the same on the anvil is also important.
@AyoubAyoub-qu5eo
2 жыл бұрын
@@forestdragonworkshop7613 w
Thanks you so much for this design. I started researching bending jigs today and yours is one of the best I've found on KZread. Great work and keep posting, thanks again.
@forestdragonworkshop7613
3 жыл бұрын
I'm glad the video was helpful. I will finish building a new workshop soon. Then new videos should appear.
Cool little jig! Nice work!
@forestdragonworkshop7613
3 жыл бұрын
Thank you very much.
very good job
Good job my friend 🤪👍
Perfect n Super. 👍👍👍
Very good idea sir 🙏👌🌹❤🚩🇮🇳
Súper 👌🙏
Sudah punya alat ini, namun baru tahu cara menggunakannya setelah melihat vidio ini, terimakasih.
@forestdragonworkshop7613
2 жыл бұрын
You're welcome
BUENÍSIMO
Good
Un buen forjador lo hace sobre el yunque.
@forestdragonworkshop7613
2 жыл бұрын
Yes, you are right, but this way it was easier and faster for me to make repetitive large amounts of rings.
👏👏👏👏👏👏👏👏
Nice basic system . U could probably put larger pipe and make larger diameter rings.
@forestdragonworkshop7613
2 жыл бұрын
It was the size I needed most often and in large quantity. I made single pieces of other sizes by hand on the anvil.
خیلی جالب بود ای کاش روش ساخت خود دستگاه رو هم قرتر بدهید
@forestdragonworkshop7613
2 жыл бұрын
It was a prototype and it worked well.
👍
@franciscoribeirotorres9943
2 жыл бұрын
Nu p8
What about bigger circumference.
@forestdragonworkshop7613
2 жыл бұрын
I do them by hand on the anvil or use a piece of pipe for it.
А для чего?
Maga adjustable straps
ВСЁ СУПЕР,ТОЛЬКО ВОТ В КАКОЙ КОМНАТЕ НА ВОСЬМОМ ЭТАЖЕ ПОСТАВИТЬ ГОРН.🤨🤨🤨
@user-ft4zk1jc1n
2 жыл бұрын
А горн и не нужен достаточно в зале поставить верстак, наковальню и ИНДУКТОР и пожалуйста изготавливайте крючки и прочие скобяные изделия...
@forestdragonworkshop7613
2 жыл бұрын
Maybe an induction heater would be a solution. Only they are a bit expensive.
مادام في وجود ملزمه تثبت الحديد فليس داعي لكل هذه الشغلات انظر ماسوره حديد وقظيب حديد وثبتها بالملزمه واشتقل وانتهت الموضوع
@forestdragonworkshop7613
2 жыл бұрын
It can be done as you say. But I did one jig for different rod thicknesses.
NO GUSTA , SÍ LO HICIERAS AL FRIO, 10/10, PERO ASÍ YO TE PONGO UN 5/10.
@forestdragonworkshop7613
2 жыл бұрын
It's faster for me to do this when the metal is hot.
0
cleance
DESLIKE. NOLIKE