Cheap 4” dial calipers: amzn.to/2VvYCcd Cheap good digital calipers: amzn.to/2VuzbHZ Cheap dial calipers: amzn.to/3iddjKN High Quality Mitutoyo digital calipers: amzn.to/2ZmlETJ

@AmadonFaul

3 жыл бұрын

Haha sweet. Iv'e been using Adam's "Cheap good digital calipers" for years. Thanks Adam. Love your tool tips. Me and the fiance' just bought a house and I'm finally getting a garage, we move in on the 10th. Looking forward to stocking it with the tools I have as well as your suggestions when the need arises. Thank you!

@kennethstarr1279

3 жыл бұрын

I always appreciate the links, Adam. I'm a professional metrologist and I use calipers daily among other measuring tools.

@gicknardner

3 жыл бұрын

I had to return my "Cheap good digital calipers," the Neiko because it was 100% useless. It would not stay zero'd after only a tiny bit of movement. This happened with two that I tried. Tried to clean them up and it was no help. I started to wonder if I was crazy and just didn't get how they were supposed to work like I was doing something wrong. I say spend $10 more on the iGaging 6" calipers (not the "absolute origin" unless you need that).

@jacksat2252

3 жыл бұрын

Hi Adam, Are you sure you have a real Digi Mito and not a Chinese clone? Because a real Mito shuts off automatically after a couple of minutes when not in use, while the knockoffs usually do too, but they keep constantly drain de batterie even if they are off. sometimes it is hard to see fake vs real. I have three Mito's 2like the one you show and a grey colored one who can function accurately even soaked in oil, and the batt last more than 3 years now, while 1 of the two black ones is death within a couple months. The dead batterie is mostly a giveaway it is a copy, there are very good copies of the real ones and sometimes hard the get them apart from the real ones besides they eat batteries and sometimes you can see it on the back label or on the little screw on top and on the grinding pattern on the yaws. Guess where got my fake one? starts with an E and ends with a Y. And no it was not a $35 one but $95 one from what looked a reputable seller in the US, not china which hurts even a bit more, could have the same for 35 bucks.

@leo7001

3 жыл бұрын

Hold your head up. We stand with you. No one believes her bs

4:41 - "For most of the stuff that I'm doing, I don't need six inches." (c) Adam Savage 2020 Now _that_ needs to be a t-shirt.

1:35 There are 4 ways to measure with calipers. 1: outside jaws, big ones 2: inside jaws, small ones 3: depth rod (right of screen/bottom of caliper) 4: step gauge, on the back between the inside jaws, the flat edges that slide over each other (left of screen/top of caliper)

@grandolddrummer

3 жыл бұрын

Came to the comments to see if anyone added the 4th way. +1

@OldManTheseDays

3 жыл бұрын

Thought the same thing.

@lance9101970

3 жыл бұрын

@@grandolddrummer yep me too

@supermillhouse

3 жыл бұрын

Same, the step that is created on the left side, on the back of the caliper when they begin to slide.

@alexholden

3 жыл бұрын

I’ve been measuring things with Vernier callipers for 25 years and I just learned a new way to use them.

There are 4 ways to measure stuff, though. The flat top of the front piece and the flat top of the back piece is perfect for measuring steps

@JerryD9000

3 жыл бұрын

Indeed. I caught that too.

@ender4555

3 жыл бұрын

I'm having trouble picturing this. Let's call the parts "outside jaws" (the long ones) and "inside jaws" (the short). Can you explain with those terms?

@ClipsByMiles

3 жыл бұрын

ender4555 I had to google “4 ways to measure with dial calipers” which answered it instantly. I was also quite confused with the explanations here.

@JerryD9000

3 жыл бұрын

@@ender4555 =====#[] if you hold the caliper in this orientation....the far right side, on the very top of the caliper, there are two planes that when the caliper is opened, will provide the same measurement as the other three methods between those two planes. Its not that easy to describe, but if the caliper is a birds head, the very top of the head is where you'll find both planes at zero.

@ndigiteu

3 жыл бұрын

@@ender4555 sorry. It's quite hard to describe. Jerry does it well though. Also: not all calipers are designed this way, I have a pair that does not have this feature

It is always an amazing thing when as a maker you have those breakthrough moments of what tools become go to’s. Thank you for sharing your passion for growing as a maker.

@Sheridantank

3 жыл бұрын

@@urAnusFighter1 Sounds like unproven accusations.

@Sheridantank

3 жыл бұрын

@@urAnusFighter1 Again as in the other thread, that's the garbage people say when they have no grounds to stand on to say anything else That "insult" is meaningless to me. It's a fact tha their is no evidence and that an accusation does not equal evidence. You can argue me all you want but every court in the world would agree with me so... yea for all intents and purposes you are WRONG. If it comes to be true that doesnt mean parade around how right you were. If one person's life is ruined by false accusations that's one too many. With ZERO evidence your comments mean nothing. I truly hopee that some day someone falsely accuses you of ra,pe.

@Sheridantank

3 жыл бұрын

@@urAnusFighter1 The fact you try to politicize something that isnt political says everything about your mindset here. For obvious reasons what he said about believe all women is irrelevant to the facts of his own case. Saying believe all women is just a message forced upon people so they say it. If you dont say it you are demonized. Just like how if you dont agree that everything about America is racist, you are a racist. So your essentially forced to say things you dont agree to avoid your own social destruction. Since you still have ZERO evidence you change the subject to politics which could not be less relevant. You're a miserable defender of your own ideas, usually this happens when your ideas are weak.

Sending my best wishes to Adam and his family to get through what I imagine is a deeply troubling time for them all.

1:32 Depending on the calipers there's actually a fourth way, from top edge of jaw (opposite side of the plunger) to top edge of the other jaw, to measure step sizes (arguably redundant with the plunger but it's there none the less)

@JimmyMish

3 жыл бұрын

Id say the plunger is more redundant, this method is more accurate when possible.

@bluelive23

3 жыл бұрын

I prefer it, the depth measuring blase one can cause cosine error much easier

@RyansHobbyGarage

3 жыл бұрын

It's not redundant, its good for measuring parallel flat surfaces like the edge of something to a wall.

@Koushakur

3 жыл бұрын

By redundant I don't mean "without use", I mean that I don't think there any measurements you can only do with this 4th method that you can't with the plunger, but the reverse is absolutely true, as in there are measurements you definitely can't do with it that the plunger can such as measuring depth of holes.

@msbrickkitten6882

3 жыл бұрын

Most calipers have the step measurement feature, less of them have the depth rod. When I teach basic metrology, when I get to calipers, I ask if anyone in the class can demonstrate all 4 measurement techniques, if so I'll buy them lunch. In 5 years of teaching the class, I've only had to buy the class lunch twice. Often overlooked, really useful feature.

I know what you mean, I have a small hobby machine shop, so I need small measuring tools, around my mill spindle, 6" calipers way to big to take measurements without raising my spindle, I used to have a cheaply manufactured 4" dial caliper, but it eventually broke, I used it more than the 6" and 12" pairs. However just recently I needed to get an accurate measurement on my mill machine without raising the z axis, I just bought a set from harbor freight of the measurement tools, so I could have a inside transfer caliper, but it came with the depth guage and steel rule, as other things as well, since I already have enough steel 6" rules, and I have another depth guage, I decided to dedicate the depth guage and steel rule for small measuring work. So I stuck the steel rule in the vice and at around 4" I bent it until it broke, took some sandpaper to the edge and behold a very convenioent small size steel rule, for those small measurements. I broke the depth guage rule in the vice also, for a miniature guage to reach down a few inches to measure to a 1/64th of an inch with the mill head in lowered position. All in all reforming these 6" measuring tools to around half there size, makes for a handy set of miniature measuring tools.

Hand tool woodworker here. Completely understand the relationship with a measuring tool. I have a strong fondness for my 6" and 12" engineering squares. Got onto this video as I am looking to go from a digital to dial caliper; thank you for pointing out the 4" size. I also have extreme preference and fondness for my marking knife. I've used many but have an irrational love for one.

Being a jewelry model maker, my first dial caliper was a 4” model. Perfect if you are working small! Glad you found one. Thanks for the video and your thoughts.

@steamgadget

3 жыл бұрын

I'm a goldsmith and a machinist, I used 6 inch calipers for 12 years, but I just got a pair of 4inch mitutoyos and I couldn't be happier!! Cheers!

Im really enjoying this lockdown series. Way to find the silver lining ;)

@stingray4567

3 жыл бұрын

@@urAnusFighter1 Why on earth is this nonsense in replies to my comment?? It has NOTHING to do with what I said. But since we're on it - "Believe all women" is a moronic idea. "Listen to all women" yes!, "Investigate reported crime and punish those found guilty" definitely. But if you're gunna blindly believe a stranger on the internet just because of their gender then Ive got a bridge to sell you...

@stingray4567

3 жыл бұрын

@@urAnusFighter1 But how do you KNOW he's a "diddler"? As far as I can see he's been convicted of nothing. He's been accused yes, and it looks like his accuser will have their day in court but until then he's innocent until proven guilty. Does it not worry you that maybe, just maybe you don't know the truth of this situation and that you might be smearing an innocent man?

@stingray4567

3 жыл бұрын

​@@urAnusFighter1 Those 2 things may be true but they don't answer my question. How do you KNOW he did these things? What FACTS do you have (and I mean facts, not hearsay, not unproven accusation, not uninformed opinion, not magic or psychic powers and certainly not "bEcAuse hEs a MAn"). Be honest, you (like me) haven't the faintest clue if he did those things or not.

@nskimharris

3 жыл бұрын

@Gennady Golovkin phew!!

Thanks Adam, glad you like our 4" dial calipers! You've got to try out the 4" ABSOLUTE Solar Caliper some day.

@AndrewSmith-qj5zv

3 жыл бұрын

You guys make the best calipers. Just got an old 8" 505-644 and just bought a used 4" 505-629.

I just got a new thimble that's really reignited my love for handsewing and embroidery and it's wild how much of a difference something that small can make in your work.

I work in a laboratory where I calibrate these on an almost daily basis. Thank you for discussing their significance.

@steamgadget

3 жыл бұрын

Metrology ROCKS!

As a European living in the US, digital calipers give me the easy switch and conversion between unit systems.

Sheet metal worker here. Press brake operator. I started out using digital calipers because that's what they had at the shop. I soon got tired of replacing batteries so I switched to dial calipers. I had to learn how to read it, but I haven't liked back. After a few years, I'd dropped them one to many times. I decided to replace them, this time I ordered the 4 inch version. I'll never go back to 6 inch calipers. 4 is all I need. I do wish they made a 4 inch caliper with a slightly deeper jaw.

I am very happy with my Mitutoyo mechanical caliper. One of my best purchases ever. I find myself using it every week during all kinds of projects. I love how you read it. I love what you can do with it. And its so beautifully made!

I find I have 3 essential digital tools: Digital calipers, cube angle finder and protractor.

@ABH313

3 жыл бұрын

I prefer a dial caliper for the same reasons as Adam, the battery is always dead when I need it but if they starting making them with AAA batteries I might consider them again lol and yes the digital angle finders and digital protractors are a God send...I also really like laser distance measure tools...way more convenient then a tape when measuring anything longer than an arm's length 👍

@TheMasheenist

3 жыл бұрын

Could you explain what is a cube angle finder? I haven’t heard that term before, thanks

@ABH313

3 жыл бұрын

@@TheMasheenist it's a little magnetic box with a screen and you place it on objects to find what angle they are tilted to or they can also be used as a level. Google it or search on Amazon and you'll see what we mean.

@TheMasheenist

3 жыл бұрын

Alan Hale gotcha thanks so much. I have heard those called digital angle finders before, I really want to pick one up for my tablesaw 👍

@ABH313

3 жыл бұрын

@@TheMasheenist yeah they are great you can stick them right to the blade in some cases and adjust accordingly. Personally I like to use a sliding t-bevel for that job most often because I'm usually fixing things instead of building them so scribing just makes the most sense. Good luck in your adventures 👍

Ever since i got a 3d printer, I've always had calipers. I got an 8" recently because it also tells me how much smaller than the print bed, my piece is

@EllaBananas

3 жыл бұрын

I got mine shortly after getting my 3d printer when I wanted to start making replacement parts for things. I realized that a ruler just isn't good enough for what I needed. Ended up getting a hand-me-down mitutoyo 6 inch dial caliper and it's been great, except that I work almost entirely in metric and it's in inches. Kind of annoying.

@casualdanger

3 жыл бұрын

Just got one for a cnc router since it came with several bits all unmarked and for using salvaged lumber but if you aren't familiar with wood, when they tell you a board is 1 inch thick it typically is 3/4" instead

The fact that Adam freshly laid a brown paper on table to get clean visuals for his storytelling makes me so happy. Thank you, Adam!

This “which side of the line I measure to” concept is a game changer!! Thanks for that bit of awareness

“Wait, let me get a ruler...” You got one tattooed on your arm! 🤷‍♂️🤦‍♂️😂

Hey Adam, I just read the news about the lawsuit on Reddit. I hope both you, your sister and the rest of your family are able to get the peace that you guys deserve. Thanks for inspiring millions to be makers!

What I love about my current digital calipers is that they easily change between fractions of an inch, thousandths and metric with a simple click of a button... makes it really easy to figure out if some part is metric or standard...

I still need to add a dial caliper to my collection. Just bought my first digital pair this year. Loving the precision! Always wanted one, very glad I caved on a pair. Using the ol' ruler or tape measure a lot less these days! From one Adam to another, thanks for sharing and educating!

Adam you've inspired me for years and I sincerely hope that these allegations are false. The fact that someone can ruin a persons credibility entirely without proof shocks me. I hope you can get past this situation and wish you the very best.

@Dashierez

3 жыл бұрын

?

Omg you wanna talk about being analog? As a 5 year old child I preferred an analog physical clock because I could “see” the time, most kids my age had no idea how to read the hands on the clock but I’ve always preferred it digital numbers. As an automotive tech I prefer physical dial measurements than digital numbers

Yes I totally understand and I have versions of both dial, and digital calipers. My favorite pair is Brown and Sharp with the black dial face.

@steamgadget

3 жыл бұрын

NICE, those are like tuxedo calipers. Very cool.

This is wonderful. I absolutely get how a new tool (or variation) can change your workflow.

a month from now: "oh, huh, how did this magnet get there?"

@SpartanMJO12

3 жыл бұрын

In a month from now the nonce will be in prison

@RacerX-124

3 жыл бұрын

Not happening.

@hopnod777

3 жыл бұрын

@@SpartanMJO12 what in the fuck are you on about

Could they not make the digital ones like they do calculators, with the little solar jobbie.....

@tylerbest1269

3 жыл бұрын

They do sell them mitutoyo sells a solar pair

@anamewillcomelater

3 жыл бұрын

Fun fact, "jobbie" means poop in Scotland.

@uploadre-upload3267

3 жыл бұрын

cheers, Would that not solve his issue?????

@JimBryson1

3 жыл бұрын

I have a pair at work, about 20 years old, but they don't have a capacitor, so anytime you reach somewhere dark to measure, they turn off :(

@chubi167

3 жыл бұрын

Upload re-upload that would solve his battery issue but not the way he goes about thinking.

Adam, I get your enthusiasm for tools and using the "right" tool; there is a feel in your hand that the right tool has that no other has. I grew up with a father who was a tool and die maker; I grew up with a lathe, mill, and drill press in our workshop. When we needed a lawnmower part, we made it from a piece of steel. I get it, and it is great to see your enthusiasm. I put myself through college working in machining, including the manufacturing of aerospace avionics; gears with tolerances in the 0.000005 inch range. The machcines you have in your shop are capable of pretty good work and I encourage you to pursue your drive for finer and finer precision. Look for ways to assure precision, accuracy, and repeatability. Tips like always move your table beyond the dimension you want and "bring it back" to your desired dimension so that you are always accounting for any backlash in the screw, no matter what machine you are using. I would like to suggest a measuring tool that, for me, is the "right" tool when measuring up to 1inch; the 0-1 Outside Micrometer. My father gave me my first Starrett which is now over 100 years old (oh, god I just realized how old I have become) and I use it all the time in the shop. It fits in the hand perfectly, it is like fitting a violin to your chin. The 0-1 Mike measures to 0.0001" with an accuracy of plus/minus 0.00005 accuracy. It fits in my apron and I don't have any worry of bending the middle bar of a caliper. See if you need more than 0-1 inch measuring device in your apron and of you don't, give a micrometer a try. Keep up the good work.

3:15 This is absolutely true! I got annoyed by the inaccuracy of my steel ruler when I was in high school making my prototypes of mobile tools tray.

I stand with Adam!!!!

@mrh8353

3 жыл бұрын

What happened to "believe women" ????

@larrybutler8948

3 жыл бұрын

@@mrh8353 That was dems saying that. Do the Math. he was 8/9 years old. A bit early for that sort of activity.

@bobmat343

3 жыл бұрын

@@mrh8353 I don't understand that at all, women never lie right? The amount of lives that have been destroyed by people falsely accusing others is disgusting. Until he's proven guilty he's innocent, you've no right to say otherwise.

@larrybutler8948

3 жыл бұрын

@@bobmat343 Just do the Math he was 8/9 years old when this supposedly happen.. about 3 years too soon for a Boy to be doing that. I am 71 and I still remember at 8/9 years old I couldn't have done anything like that.

@mrh8353

3 жыл бұрын

@@larrybutler8948 "That was dems saying that" yeah.. and Adam too, look it up. "he was 8/9 years old. A bit early for that sort of activity." Yeah i agree that is early, and it would suggest that maybe Adam has had some bad stuff happen to himself at that age as well

I believe AvE did a video on calipers, specifically about battery usage. The Mitutoyo uses a proper switch that actually stops the slow drain that kills batteries in cheaper calipers.

@jasminebuckland1227

3 жыл бұрын

Maybe now I can measure my last heart string

@1pcfred

3 жыл бұрын

Mitus must use electricity when they're off because they remember their position. The electronics are just that good in mitus that you get practically shelf life out of a battery.

@microbuilder

3 жыл бұрын

@@1pcfred Yeah that sounds right, I'll have to rewatch his video, I thought he mentioned something about the switch.

@saschaschneider6355

3 жыл бұрын

I simply take out the battery when my digital calliper is not in use for more than a few minutes

@1pcfred

3 жыл бұрын

@@microbuilder beats me. There's no way a caliper can remember its position if it turns completely off though. Unless they're making them with some kind of persistent memory today? If I pull the battery out of my calipers I have to reset it. But I have an old pair of Mitus. The battery lasts so long I forget in between how to reset them. I have to hold one button down for a while. Which I never remember. Might be the REL button? I don't know.

Hey I remember those. Used them in machine shop in high school. I also used them at one of my first jobs. I worked at a machine shop and one of the things we made were punches for soda cans back in the late '70s.

I love my 4" Mitutoyo Calipers! Been using them at work for 37 years. I calibrate tools here in the shop too. The 4" always are a little more accurate. Nice video!

One day build: A nice holster that allows for easy storage and quick access.

@RandomStuffGarage619

3 жыл бұрын

I drilled a mesh basket (size of a solo cup) to a shelf on my bench that contains various and commonly used doodads like pencils exactos hex drive tips etc. Its my organized chaos dispenser lol

@MattLitkeRacing

3 жыл бұрын

McMaster sells a leather holster number 3278A41

@gierhedd75

3 жыл бұрын

Kydex for a nice satisfying click. Hahaha

@RandomStuffGarage619

3 жыл бұрын

Oh I actually keep my mutitoyo in its original case. Its like the holy hand grenade of Antioch when I open it lol

@Nilguiri

3 жыл бұрын

@@rifleshooterchannel208 stfu, you freak.

Somewhere along the video I thought he cut his 6" calipers

@mildyproductive9726

3 жыл бұрын

I chopped a 6" digital caliper down to 2" long to make a depth indicator for a small drill press. I have read that digital calipers have a pcb running the length of the calipers, underneath the sticker. Somehow the caliper measures capacitance of the pcb? Anyhow, I figured I would try and see what happens. Yes, there is a pcb under the sticker. I chopped right through with a cutoff disc and sanded it to length. Works fine.

@kevinvermeer9011

3 жыл бұрын

@@mildyproductive9726 It should work fine even after being cut, there's no current going through the PCB part, and no traces running longitudinally. The copper on the PCB is a high-resolution, complicated multi-row barcode that is read with the capacitive sensing system on the moving head. Think of an optical encoder, but unrolled and measuring capacitively rather than optically.

@elsaeraser

3 жыл бұрын

@@goodtwogo #BelieveAllWoman lol

@kaviprashanna

3 жыл бұрын

@@goodtwogo I was having a good time. Why would u reply to my comment

Doing instrument repair unused a set of crap digital calipers for about 5 years and just replaced them with a set I’d decent/moderate digital. Your statement on measuring to the line makes perfect sense, and just got me to order a set dial calipers. Thanks for inspiring us all to get better at our craft!

I love working with analog tools. I had a digital caliper and found myself always going back to my analog ones. In a hurry it might be more error-prone, but for me it is a nice reminder to calm down when I am in my shop, slow down a bit and do the work I am doing a little bit better and with more attention. That's not saying I am not using any digital tools - I do! But I like the way analog tools work and feel and how they force you to be more careful in everything you do, even when it is a simple measurement. I remember my grandfather working in his tiny, tiny shop in the basement for hours over hours on his small projects and always carefully measuring things, writing numbers down on paper and do the math there. I am not a professional, I work in my shop for my private entertainment and with that I often think back to my grandpa and I like the idea that I am doing things as close to what he did back in the days - it connects me to him again :-) Long comment to say: I like analog better than digital, especially when measuring things and yes - dead batteries suck ;-)

Tested video pops up... STOP EVERYTHING AND WATCH 😅👍🏻

Yeah, but..... I really like the way my digital calipers can switch between inches and metric with a touch of a button.

@Spectral_Penguin

3 жыл бұрын

Agreed, especially useful when stuck with a mix of imperial and metric hardware. Mine even do fractional inches.

@Colhogan06

3 жыл бұрын

I agree, having that flexibility can make a job so much easier. Especially if someone gives you a job with measurements that only a digital caliper can measure. Mine does fractions, millimeters and inches like the other person that replied here. You can't beat the convenience.

@c0mputer

3 жыл бұрын

Totally. BUT they do make inch/metric dial calipers with two independently sweeping hands. That being said, I use digital ones.

@dedklownx

3 жыл бұрын

And then you have the old timers that just have the math memorized from decades of conversations

@crhonda6425

3 жыл бұрын

.03937 and 25.4 is what I use to convert if it’s in mm (almost always is). The metric feature is handy in some cases but when I’m making a part with machines and dial indicators that read in inches converting is the way to go.

I bought my first Mitutoyo 6” dial calipers in 1994 and I still have them in the original plastic case. I agree that they are in essential tool. I actually used mine the other day comparing an original car part with a replacement car part and measure the wall thickness of the plastic molding. As I recall the calipers do you need calibrating from time to time. Keep bringing great content.

I fully understand and have had the exact same experience. For a long time I was doing a lot of parts that were 6~7" long. So I was having to use a 12" caliper day in and day out. And then I found that 8" calipers exist. They've been my go to calipers since. :) (Still hunting for a good set of 4in for stuff around the house) Changing topics a little, I have gotten so used to calipers for measuring things that I have 2 or 3 inexpensive sets around my home for doing quick "hey what size is bla widget before I go to the store to get another one".

I paused this video 3 times, trying to hear the siren outside my house. then resumed, heard it again, paused, listened, repeat. OHHHHHH the sirens are on the VIDEO. DOH!

@brandondabreo421

3 жыл бұрын

DID THEY ACTUALLY COME TO ARREST HIM? JFC

@thesawdustfactory

3 жыл бұрын

It was the Metric Police. Adam's address is 666-1/2 but the MPs got their conversion wrong and went zipping by looking for 16929.1.

@steamgadget

3 жыл бұрын

LMAO! I did the same thing.

4:41 "for most of the stuff I'm doing, I don't need 6 inches" That's what she said.

@MrBranboom

3 жыл бұрын

We're all just work'n with what we got.

@brandondabreo421

3 жыл бұрын

Bad timing my dude. Read the nytimes article and delete this if you care about adam

@MrGonzonator

3 жыл бұрын

@@brandondabreo421 ouch. It was an honest to goodness joke told in simpler times. I'm sure Adam would appreciate a good laugh. I tell you what, I'll leave this here and if he asks me to remove it I will.

@GCJII

3 жыл бұрын

Brandon D'Abreo it’s the NY Post, (not the) NYTIMES. The ny post just makes garbage.

@MrGonzonator

3 жыл бұрын

@@GCJII I read it in the Washington Post, does it materially change the facts of the matter?

I just started making, and I bought a $30 dial caliper over the $15 digital, because of your recommendation and I love them

I'm a Metrologist (measurement scientist). Adam geeking over measurements makes me happy.

@steamgadget

3 жыл бұрын

3 Cheers for metrology! Metrology makes the world "not" round!! 👍

"Make it one thirty-second..." "A fat thirty-second or a skinny thirty-second?" I have had this conversation...

@Sheridantank

3 жыл бұрын

Kristin Britt Damn does it make me cringe when people add “union” to their title. You’re an electrician, you work in a union. You’re not a “union electrician” nor is the union part relevant to your comment.

@xl000

3 жыл бұрын

@@Sheridantank union people tend to work differently... I once was tasked to sort through boxes of archives with a guy in a union, in a storage room. Just walking there ( it was in the back of the supermarkt) took 5 times the normal time. He has some kind of gift of making it look as he was working while doing something else ( mainly talking with other union people...)

@Sheridantank

3 жыл бұрын

xl 100% can agree. Unions are trash. I was harassed and insulted by someone when new as a temp at a factory by a union worker. I flipped shit on them and they were like “well I’m in a union so good luck getting me in trouble”.

I love my calipers, I only have the digital calipers but this is food for thought about battery operated devices, during the lockdown, it has been more difficult to get out and get more batteries for our electronic devices and there are analog devices like these calipers that don't require batteries, hhmmmmmm, makes one think.

@treborrrrr

3 жыл бұрын

@@ParabolicLabs I actually modded my cheapo digital calipers to have a AAA on top of it. I think I've changed that battery once in the past 5-6 years or so. Now I have a proper Mitutoyo instead and I'll happily replace that battery every couple of years or however long it lasts.

I never thought i'd use a caliper everyday but it's quickly become my most used tool.

I like this video. I feel the same way about the evolution of how tools are viewed. I have gone from using lineman's and needle nose pliers exclusively to using slip lock pliers and now to adjustable knipex style pliers. All the while being sure that what I was using was the best. Keeping an open mind and always having the mindset to improve is a critical life skill that will serve indefinitely.

“Just a little long for me, for most of the things I’m doing I don’t need 6 inches” -Adam Savage

@lawsonszerencits7027

3 жыл бұрын

Went looking for this, thank you lol

I could listen to your anecdotes all day. I sometimes think I like tools more than making stuff.

Beautiful and precise tools from Mitutoyo, Made in Brazil since the 70’s :) São Paulo state. Long history of Japan / Brazil relationships

@longinus665

3 жыл бұрын

I had no idea, interesting!!

every single time he says "thousandth of an inch" I have to make the conversion to metric in my head....

@buddyclem7328

3 жыл бұрын

0.001in = 0.0254mm Did I get that right?

@easyremembered

3 жыл бұрын

@@buddyclem7328 no, 25.4 microns, nobody in their right mind would use millimetres in that range

@venkatperla

3 жыл бұрын

@@easyremembered they would use micro meters,not milimeters and God no inches

@williescott5439

3 жыл бұрын

@@easyremembered I guess I'm not in my right mind, on high precision machines I work with, that's exactly how we would write out .001" in mm

@microbuilder

3 жыл бұрын

This is one big benefit of digital calipers, it'll convert for you...I switch between both all the time depending on what I'm doing, its really helpful.

"...I don't need 6 inches" Yeah...same >.>

Made in Brazil! It is my country. I m so satisfied with this!! Thanks

Thanks again for all the tips, and distractions during these interesting times

Adam not sure what to think about the accusations trough forward from your sister. Is this something your going to address or wait for the trial? I understand either way.

@chamoo232

3 жыл бұрын

Even their mothers say she has mental health issues.

@Shane_O.5158

3 жыл бұрын

it's a sad day when a man's reputation gets dragged thru the mud by an accuser, when the accuser is found to be lying they should go to jail for 20 years because lies like this can ruin a person's life.

@ddupree79

3 жыл бұрын

Shane Forsythe Allegations should always be investigated to the fullest extent possible. The accuser, however, should indeed face the same sentence range if they are found to be lying. (Or receive psychological help depending on the situation).

@Shane_O.5158

3 жыл бұрын

@@ddupree79 of course all allegations need to be investigated, but nobody's name should be named and made public, or put in the news until AFTER he/she is found guilty, in fact it should be a jail sentence for dragging a person's name thru the mud. ( and mental illness is no excuse, they need either jail, or a mental ward for the rest of thair life, where they cannot hurt anyone else ( including themselves )).

@3398halofreak

3 жыл бұрын

@@ThePilot3332 hu didn't hear that very interesting check charts for someone so involved in the Hollywood scene. But what Shane was saying a lot of people don't even look at when it's a celeb or person they like it's almost guilty full proven innocent in the court of public opinion.

Prediction: When you switch from Imperial to Metric, you'll also switch to Digital Calipers. It's just a logic fit, IMO

@E_Pluribus_Unum_1776

3 жыл бұрын

Metric.... Never.

@tedhaubrich

3 жыл бұрын

Yea, imperial fractions are easier, 12 just chops up more neatly in more ways than 10 does and makes more sense on a dial. It's probably why we don't use metric time. Whereas obviously our base ten numbering system looks simpler in a digital decimal form.

@Strassenkicker

3 жыл бұрын

@@E_Pluribus_Unum_1776 It's the best and simplest. You are just used to complicated Imperial measurements.

@E_Pluribus_Unum_1776

3 жыл бұрын

@@Strassenkicker I agree, metric is super simple... But so is imperial or as the US calls it standard. You say its complicated, I disagree. Both are very easy to understand.

@Strassenkicker

3 жыл бұрын

@@E_Pluribus_Unum_1776 It's not standard where I am from, or anywhere else in the world but the US. That kind of makes metric the standard, doesn't it? Imperial is not easy to learn in comparison to metric, and that's what matters. Imperial is complicated when you have to switch through the units. Or when you are forced to use fractions.

I relate to this "Ah ha!" moment at a deeper level: I've heard "recognition is liberation," that is to say, when you actually "see" what it is... for what it is... you're already 90% on the way to the solution. in your case it was the 4" Calipers and it's happened to me as well about tools, or workflow, or life in general... it makes a profound shift in what you do and how you interact... yeah... It's pretty COOL when it happens 😎 We change and evolve, it's part of our process.

Until I watched this, it never occured to me that one can use the end to measure depth. I watch these videos to enjoy Adam's energy... but I'm also learning an awful lot. Thank you!

People, put the pitchforks on hold for a bit. On one hand, his sister has zero proof and even their mother disagrees with her accusations. A man's entire career and life shouldn't get destroyed based solely on a single person's statement. Just saying, he deserves the benefit of the doubt until/unless proven guilty. If he IS guilty, then that's horrific as fuck!

@PeninsulaPaintings

3 жыл бұрын

@@TANTRUMGASM So we're supposed to convict/cancel a man solely on word alone? I'm not saying he definitely isn't what she claims, I'm suggesting taking a nuanced approach to this until/unless some evidence comes forward. Rape accusations are really serious, they need to be handled with absolute care, we can't definitively decide what the truth is based on bias.

@altcut02

3 жыл бұрын

@@TANTRUMGASM According to their mother, she has been suffering from mental issues and has been accusing her entire family of various abuse for years

@MisterWealth

3 жыл бұрын

@@PeninsulaPaintings Isn't that what happened with that Kavanaugh guy? Cancel him, ask questions later. Turns out all the people the woman brought as witnesses said she was lying lol But even Adam said believe all women so...

@PeninsulaPaintings

3 жыл бұрын

@@TANTRUMGASM I'm a female, dude. And you don't know how old I am. I'm not 'sticking up for a chomo' I'm taking a neutral approach until further notice, as everyone should. Calling him a 'chomo' already without evidence or even a trial is ridiculous.

@PeninsulaPaintings

3 жыл бұрын

@Big Rock If you're talking about feminists, don't. I'm not one. I actually want equality, not female superiority - and I can't stand double standards, which is why I'm taking this neutral approach. I'm not automatically believing his sister just because she's female, nor do I disbelieve her just because Adam is a celebrity. Bloody hell, I admit i'm female and that automatically lops me in with radical feminists.

"For most of the stuff that I'm doing, I don't need 6 inches" TMI Adam, TMI.

@StantonDJJoker

3 жыл бұрын

This is gonna be real funny in a few hours.

Thanks for the tool tip! I've been looking for analog calipers for my husband and wanted to (more or less) buy them once but was unsure of a quality brand. The Savage Seal of Approval is greatly appreciated!!

I've been using 4" calipers for a while now too. It's rare that I need anything larger. For me the big down side with dial calipers is there are so many things I work with that can be either metric or inch, and the ability to switch quickly is very handy.

@1pcfred

3 жыл бұрын

You just need a conversion chart. You need one of those anyways. I have one up on my Google drive. Save it and open it someplace not Google drive docs.google.com/document/d/1quDHoEjSzVA5Pa2s-qScuoi8KF3oQNHdnl5GV0J2RKE/edit Because Drive screws up the formatting.

Here before the comments are locked!

@mrh8353

3 жыл бұрын

Won't be long now...

On the court thing; Why do people feel they are in a position to judge on this? How do they feel they have enough information even to make that judgement? I think people just want to know if they should feel guilty or not about watching Adam from now forward. I'm trying to tell myself these two are separate, but here I am. Whether the allegations are true or not, for me it's more telling how he responds to his sibling now than what happened 50 years ago. If he treats her like shit for instance

@Largetalons

3 жыл бұрын

On one hand you will have people who have been through this and didn't have their own family believe them. On the other you will have people who have had family with substance abuse problems that have sunk about as low. Either way it'll tug at those people. Just a shame how fast people rush to judgement these days.

The Mitutoyo dial calipers are the most useable I have had, I lost my last set a while ago and have been using an antique, now it's time to look for a new set.

I hear ya there adam. As an industrial machinery mechanic, my tool collection keeps growing over time but i find myself going back to my old trusty tools that were there for me in the beginning. I feel the same way you do about calipers. I love my digital caliper but my dial caliper will always be my go to because of the battery issue. I havent looked to see if there are solar/ light powered ones yet to see how reliable they are. Maybe we should look in to that!

other people to allegations: apology video Adam Savage: *4" Calipers*

@fujifilm5127

3 жыл бұрын

@@joebryant8500 *12" Calipers*

@mrh8353

3 жыл бұрын

@@joebryant8500 "I accuse you of sexually abusing your dog." sounds like a liberal projection, do i need to call the animal services on you???

*What do you call a factory that produces OK products?* A SatisFactory.

@buddyclem7328

3 жыл бұрын

Nice!

I got my first set of calipers at PGS Gunsmithing School. It was a 6” Mitutoyo dial caliper. Then an old freind retired machinist gave me his 6” Starret and 0”-1” Brown & Sharp micrometer. Both great Companies, great products.

I feel the same about my 4" (100mm) Empire Brass Vernier cal. Tiny and sturdy for any pocket, and as accurate as I need without a fragile dial that can get broken off in some cases.

the allegations make no sense to me. keep doing your thing man!

So many sheep are quick to attack Adam due to accusations towards him. Think before you attack, I would hope you guys are better than that

I enjoyed your presentation. I only have a digital caliper and what I really like about it is the ability to measure in not only thousandths of an inch, but with the press of a button I can see what the fractional or metric equivalent is.

Adam, After watching this video I went looking for a new more accurate caliper vs the plastic one I have been using. I went to a Pawn Shop and found a Central Tool 6" dial caliper for 15 bucks. It cma with a .01 check piece. I took it home and measure some things and it is Awesome. Thanks for the tool tip. Be safe.

Please dont let these be true man

@altcut02

3 жыл бұрын

Its not, According to their mother, she has been suffering from mental issues and has been accusing her entire family of various abuse for years

@nogginclonith7867

3 жыл бұрын

@@altcut02 Yeah i don't really know what to think

@sdghtjsdcgs

3 жыл бұрын

@@altcut02 Very well could be the case. Could also be the cause of her mental illness.

@OGPatriot03

3 жыл бұрын

Honestly though, how would you feel it it was true? I believe the allegation states that at the time of his abusing he was 9 to 12 years old, now none of us know the full extent of the allegations, but do you think we should hold him responsible for the actions of his childhood (when his parents were the responsible parties and he knew nothing, if it's true it indicates he was probably abused himself) and if so, to what degree? Seriously though, how do we handle punishing a child for a heinous crime some 40 years later? To me the crime committed when he was a child is essentially irrelevant, the more egregious crime would be denying it if it's true, but then there are certain considerations to be made like what damage to the family overall would be done if he admitted to it in today's world of cancel culture where you're condemned for eternity for something you did in the past, whether you learned from it or not doesn't matter. Personally I think that if it's true then the right thing for him to do would be to publicly address it and for him to explain why it was awful and what enabled him to do such a thing so that everyone else can get a little more insight on how to avoid doing the same things. That would be the only silver lining to be had, for us to examine how this scenario was even possible, the mistakes he made and the mistakes his parents made that allowed this to happen in the first place. But we don't live in a forgiving era, and the public would absolutely destroy him for doing so, because instead of us viewing him as a person who had an incredibly troubling past (due to what ever horrible conditions that existed or existed in his mind at the time of his offense) who was able to recognize his actions and now understands them to be wrong, we view him as this entity that should be forever punished for the horrible thing he did - When he was between the ages of 9 and 12....

The comment section is such a shitshow rn

@altcut02

3 жыл бұрын

Its worse now :( I feel so bad for him that he has to deal with people shitting on him that don't even bother to look into the facts of it

Love your content! I see your using the new table already!

I did quite a lot of metrology and calibration when I was an apprentice toolmaker. one of the projects was to make a sine bar, and the rollers for it, then check it with slip guages. I also prefer manual calipers over digital, but I go a step further and use a plain old Vernier caliper. I feel like I'm doing something then. And they are durable. Displays and dials can and often do get damaged in a busy machine shop or toolroom environment. If you can find the time, and a trade college that will have you, I strongly urge you to look into toolmaking and get certified. You will check off a lot with your current qualifications acting as prerequisites for a lot of the toolmaking modules. If your eyes are open now, I truly believe you'll be blown away by toolmaking. It opened up the world for me and taught me how to design and make and fix anything. I mean that literally. You will never see the world the same again when you look at any product and can be fairly certain you know how it was made, or how to improve it or how to fix it.

Wtf is going on Adam?

@mrh8353

3 жыл бұрын

his past has caught up with him

Hoping Adam sorts the issues out with his nutcase of a sister. Sick and tired of people coming out of the wood work to try and cash in and ruin peoples lives.

@DW_Death

3 жыл бұрын

@@urAnusFighter1 shade

@MrTony-rx7tk

3 жыл бұрын

This thread went red real quick

@leavemealoneandgoaway

3 жыл бұрын

hope you said the same thing about Kavanaugh

thank you for this upload.. i have said my self if and when i would get into 3D printing.. that a good set of calipers will come very handy to see if the print came out correctly

I have always gravitated to dial verniers as I hate batteries running out, it's great to know I'm not alone in this.

Inb4 this video is disliked bombed to hell because of the rape allegations.

Blob

@BloatedBumbleBee

3 жыл бұрын

Chris Schwanger what does this have to do with callipers? Go back to school

@mrh8353

3 жыл бұрын

@@BloatedBumbleBee the bloated doth protest too much, methinks.....

Love me some Callipers, have digital, but for trust factor analog is the way to go. Love getting an Adam Savage one day video.

I love my 4" calipers. I build big stuff at work, so there my standard go-to is 12", but at home on smaller parts, the 4" set is agile and frankly indispensable.

Its the BLOB!

@eastendthug

3 жыл бұрын

I understood the reference

Just heard the news Adam. Honestly sounds like your sister need some help. Hope everything works out for you and family.

@bonobo8803

3 жыл бұрын

It's really great that you have your family's support on this. This must be really hard for you and your family. Hope you all get through it and your sister finds the help she needs.

My father is the engineer and CEO of the family biz. He always has a great set of ID and OD calipers, along with a scale in his pocket. ❤️🇺🇸👍 Agree that even the most expensive digital ones don't seem as accurate. We make precision aircraft tools where millionths matter.

There are also 3" calipers, which was the first size I bough (to measure some very small things, of course) that don't even have a spike. I later bought 6" and 12" calipers for different, bigger sorts of jobs. At the same time I bought the 3" calipers, I bought a digital angle measurer (not a protractor as it doesn't work that way, I've bought more since). At the time I bought the other two sets of calipers, I bought a high-precision vernier protractor which does have some advantages (like being easier to lock to measure certain object's angles, but damn had to get into the works of my Kossel Delta to check that the thing's squared up properly).

whats up with your sister? Why would somebody lie like that?

@luiscamara1

3 жыл бұрын

He said so himself. She's been harassing her family for years look for what he calls a "financial bonanza". Even their mother vouches for him

@nogginclonith7867

3 жыл бұрын

@Hemp Tech I don't know what to believe I'm just gonna see what happens before deciding

@jakobvanklinken

3 жыл бұрын

Why do people feel they are in a position to judge on this? How do they feel they have enough information even to make that judgement? I think people just want to know if they should feel guilty or not about watching Adam from now forward. I'm trying to tell myself these two are separate, but here I am. Whether the allegations are true or not, for me it's more telling how he responds to his sibling now than what happened 50 years ago. If he treats her like shit for instance

believe women, right? ahahahaha, have fun Adam

@altcut02

3 жыл бұрын

According to their mother, she has been suffering from mental issues and has been accusing her entire family of various abuse for years

@mediaphile

3 жыл бұрын

Believe all women means take the claims seriously and investigate them. It doesn't mean they're automatically true.

@mrh8353

3 жыл бұрын

@@mediaphile "Believe all women means take the claims seriously and investigate them. It doesn't mean they're automatically true." In the case of Kavanaugh, where the hashtag stemmed from, yes, yes it did.

@mediaphile

3 жыл бұрын

Mr H You're saying we should assume the claims are true without investigation?

@mrh8353

3 жыл бұрын

@@mediaphile Yes.

NIce to know this, I have a bunch of normal calipers from my grandad's workshop but they are a little bit rusted. Always dreamt about buying a digital caliper, now I know better and dream about 4" dial calipers.

I have a very cheap pair of plastic student's vernier calipers that I use around the house, and even that, which isn't terribly precise, and that I have to re-remember how to read the vernier chart every time I use them, is just an incredible upgrade over measuring tape. Those dial calipers look fabulous.