Easy to use, with angle control, air cooled, timer and clock Made with recycle components plans for free to download 1drv.ms/u/s!BGuLaO8WcIELbc42R...
Жүктеу.....
Пікірлер: 25
@MrJcasilva5 ай бұрын
😊 perfect, very well done!
@ahmadghalem67342 жыл бұрын
WOW THIS IS PERFECT BEST ACRYLIC BENDER VIDEO EVER SEEN LITERALLY GOOD JOOB !!!! , i will made one like this thank you
@prosediy_
2 жыл бұрын
:) i am glad you have enjoyed. Thanks for your comment
@pjcpjc47273 жыл бұрын
Amazing! Congratulations.
@prosediy_
3 жыл бұрын
Thanks, i am glad you have liked
@cryptofuture9592 Жыл бұрын
Glad to watch it
@prosediy_
Жыл бұрын
I am glad you have enjoy it, thanks for your feedback
@arieugonycana2 жыл бұрын
Excelente trabajo, enhorabuena.
@prosediy_
2 жыл бұрын
Gracias, me alegra que te haya gustado
@jjloop9644 Жыл бұрын
Execellent job. This power variator feed ac voltage to your heat element or it uses dc voltage to your heat element?
@prosediy_
Жыл бұрын
Thanks for hoje feedback, this poder variator feed AC voltage.
@jjloop9644
Жыл бұрын
@@prosediy_ Thank you
@arieugonycana2 жыл бұрын
Sería posible decir las medidas por favor. Gracias y un abrazo.
@lawrencebrazeau2 жыл бұрын
hi, nice work, thanks for the video, i built a machine similar to your design and i was making a u chanel which was 38 inches by 38 inches with a 3 inch bend at each end That turned out ok but now i am bending some 2 1/2 strips which i am bending in half to make a angel piece for my project, but the angel pieces are comming out bowed, so i am trying to figure out how to avoid the bowing each piece is about 30 inches and the bender i made can accept a 48 inch piece of plastic. Am i bending it to slow..too fast? or not cooling it down ?. like i said the big sheet turned out pretty straight but the smaller pieces are not so straight. i was thinking to use a heat gun and sandwhich the 2 1/2 inch pieces between two pieces of angel iron to straighten the bowed pieces?
@prosediy_
2 жыл бұрын
Thanks for the comment. Does your machine have power Control? Try less temp. In my machine works doing that and the redults are great. Thanks again
@abuali44852 жыл бұрын
👏👏👏👏👏👏
@prosediy_
2 жыл бұрын
Thanks 😃
@whongthai1301 Жыл бұрын
post bending 2-3mm thick acrylic it starts to stress crack after a few days.... is it because its too hot or cold ? or too short a dwell time ?
@prosediy_
Жыл бұрын
Does your machine haver poder control?
@prosediy_
Жыл бұрын
If yes, try less temperature. In the past i fold a lot of acrylic pieces and what i did was pre-heated with the hot air gun, try ir. Regards
@eduardoamorim64662 жыл бұрын
f### Awesome Hug my friend
@prosediy_
2 жыл бұрын
Thanks my friend, hug
@quemeese3 жыл бұрын
will this also work for bending Worbla?
@prosediy_
3 жыл бұрын
Yes, this machine also bend Worbla, Just need to use less power. For bending Worbla i use low temp. and short time. Thanks for watching
Пікірлер: 25
😊 perfect, very well done!
WOW THIS IS PERFECT BEST ACRYLIC BENDER VIDEO EVER SEEN LITERALLY GOOD JOOB !!!! , i will made one like this thank you
@prosediy_
2 жыл бұрын
:) i am glad you have enjoyed. Thanks for your comment
Amazing! Congratulations.
@prosediy_
3 жыл бұрын
Thanks, i am glad you have liked
Glad to watch it
@prosediy_
Жыл бұрын
I am glad you have enjoy it, thanks for your feedback
Excelente trabajo, enhorabuena.
@prosediy_
2 жыл бұрын
Gracias, me alegra que te haya gustado
Execellent job. This power variator feed ac voltage to your heat element or it uses dc voltage to your heat element?
@prosediy_
Жыл бұрын
Thanks for hoje feedback, this poder variator feed AC voltage.
@jjloop9644
Жыл бұрын
@@prosediy_ Thank you
Sería posible decir las medidas por favor. Gracias y un abrazo.
hi, nice work, thanks for the video, i built a machine similar to your design and i was making a u chanel which was 38 inches by 38 inches with a 3 inch bend at each end That turned out ok but now i am bending some 2 1/2 strips which i am bending in half to make a angel piece for my project, but the angel pieces are comming out bowed, so i am trying to figure out how to avoid the bowing each piece is about 30 inches and the bender i made can accept a 48 inch piece of plastic. Am i bending it to slow..too fast? or not cooling it down ?. like i said the big sheet turned out pretty straight but the smaller pieces are not so straight. i was thinking to use a heat gun and sandwhich the 2 1/2 inch pieces between two pieces of angel iron to straighten the bowed pieces?
@prosediy_
2 жыл бұрын
Thanks for the comment. Does your machine have power Control? Try less temp. In my machine works doing that and the redults are great. Thanks again
👏👏👏👏👏👏
@prosediy_
2 жыл бұрын
Thanks 😃
post bending 2-3mm thick acrylic it starts to stress crack after a few days.... is it because its too hot or cold ? or too short a dwell time ?
@prosediy_
Жыл бұрын
Does your machine haver poder control?
@prosediy_
Жыл бұрын
If yes, try less temperature. In the past i fold a lot of acrylic pieces and what i did was pre-heated with the hot air gun, try ir. Regards
f### Awesome Hug my friend
@prosediy_
2 жыл бұрын
Thanks my friend, hug
will this also work for bending Worbla?
@prosediy_
3 жыл бұрын
Yes, this machine also bend Worbla, Just need to use less power. For bending Worbla i use low temp. and short time. Thanks for watching
@quemeese
3 жыл бұрын
@@prosediy_ thanks