Can you do a fem analysis for the rotary friction welding process please.

Really well man, could you make a video Rotary Friction welding RFW, i need that one. Please brother

Please provide the full video

I try to do the same you do on vid and dont work, theres some errors that pop off; about boundary conditions.

What is use of reference point 2 ??

Sir. Spin welding can be simulate in ansys

how long did it take to get the results?

Analysis is aborted because 1 nodes have dof on which velocity/displacement/acc/base motion etc. Constaints are specified simultameously. Any help?

the tool wont pass through the plates until you give the johnson cook damage values for both the plates.

@NoName-qt2ly

Жыл бұрын

Can u please help me with this. I think I am applying it wrongly.

Although I was able to simulate the process well, the temperature rise is extremely low for me. Anyone else faced a similar issue ?

@animo3019

Жыл бұрын

Hello please send me result

I have done everything as you shown. But at the end when I submit the job it is saying that student edition is restricted to 1000 nodes. What should I need to change sir??

@premkumar-cr3gn

4 ай бұрын

did you resolve this isssue sir

wich method

Analysis is aborted because 1 nodes have dof on which velocity/displacement/acc/base motion etc. Constaints are specified simultameously. What to do plz help.

@nicolaslutkens8854

3 жыл бұрын

Look at BCs that happend when one node have 2 boundary conditions, so look at that.

@akshittyagi5267

Жыл бұрын

Provide velocity to plates carefully. Seems you selected reference point along with the plates.

thank you so much, I need any youtube ( friction for thin film coating on titanium metal) could anyone help me.

@speechoftheworldsgreatests4768

3 жыл бұрын

1700 #materials for #Abaqus including #elastic, #plastic, #damage, etc. information. For only $ 300 !!! en.banumusagr.com/shop/matlib-for-abaqus/

Can you mention the material of plate and fsw stirrer

@speechoftheworldsgreatests4768

3 жыл бұрын

1700 #materials for #Abaqus including #elastic, #plastic, #damage, etc. information. For only $ 300 !!! en.banumusagr.com/shop/matlib-for-abaqus/

Can anyone share this file of simulation

Please add audio also

What kind of material in this vdeo yaa..?

@speechoftheworldsgreatests4768

3 жыл бұрын

1700 #materials for #Abaqus including #elastic, #plastic, #damage, etc. information. For only $ 300 !!! en.banumusagr.com/shop/matlib-for-abaqus/

Will it possible in Ansys workbench v16.2

@speechoftheworldsgreatests4768

3 жыл бұрын

1700 #materials for #Abaqus including #elastic, #plastic, #damage, etc. information. For only $ 300 !!! en.banumusagr.com/shop/matlib-for-abaqus/

Which method ALE method? CEL method? Eulerian method? Langrangian method?

@preethamreddy6726

2 ай бұрын

Dynamic,Temp-Disp,Explicit

can you share the original file? I followed the tutoral, but it cannot work.

@Abaqus_basic

3 жыл бұрын

Any model here my friend is for 5 dollars WhatsApp number 0778894272

@LovepreetSingh-kn2wv

3 жыл бұрын

@@Abaqus_basic hey mate! what's your country code?

@Abaqus_basic

3 жыл бұрын

+213778894272

@NoName-qt2ly

Жыл бұрын

@@Abaqus_basic Wrong number. This is not on whatsapp

@Abaqus_basic

Жыл бұрын

@@NoName-qt2ly ismailboubou000@gmail.com

An excessive temperature rate occurs in solving the heat transfer equations. This usually indicates that some elements are badly distorted or an error exists with model definition. You can check the temperature values and see if the distorted elements exist. how can i solve this

@nicolaslutkens8854

3 жыл бұрын

I have the same problem and i think its about Johnson Cook Values, because plates deformation is plastic, then the pin of the tool wont past throw the plates; but i you solve this pls tell me.

@avezshaikh4502

3 жыл бұрын

Did anyone solve this, same problem?