$900 Drill VS $5 Block - THE SHOP Part 10
Тәжірибелік нұсқаулар және стиль
Hole saw mandrel with eject feature
ezeinnovation.com
4 in core bit (other diameters available)
amzn.to/3QS5N8N
Bosch SDS max roto hammer
amzn.to/3JWi3CW
1/4" x 12" drill bit
amzn.to/3PxBMKe
Milwaukee Big Hawg kit
amzn.to/3CaHQ8k
Broan vent light bluetooth speaker
amzn.to/3A7kT3A
pvc cement/primer brush
www.homedepot.com/p/OATEY-6-i...
Пікірлер: 416
I put in a bunch of those fans and the complaints I was getting is the flapper in the vent kept going tick, tick, tick from a slight breeze so I went to the tire store and got some half ounce self stick weights and put one one the bottom of the flap and the tapping stopped so the rest of them stay in the truck. Now every one I install gets a weight automatically. The fan has more than enough velocity to blow the flap open.
@Floridamancan
Жыл бұрын
Cut that weight in half. Does not need any where near that much weight.
@paaao
Жыл бұрын
OR, put a strip of sticky back pads like people put on cupboards/gates etc...
@MoneyManHolmes
Жыл бұрын
Good idea. I was thinking about driving a short screw through mine to act as a counter weight that would never fall off, but I installed an exterior vent with a dual damper and it solved the problem.
@Victor-nn2wi
Жыл бұрын
The pipe he used is wrong you have to insulated pipe because the condensation will go threw the ceiling
@musicteacherbuilder
Жыл бұрын
@@Victor-nn2wi he literally pitched to the outside. It will drip outside the structure.
As a plumber in the UK we call this core drilling. Typically I wouldn't use hammer, just rotary. Its a cutting action which wont blow the brick/ block on the exit side of the hole. Also as a few others have commented, removing the pilot bit immediately after getting the core hole goings a good idea because it 1. means you wont loose the tapered pilot bit and 2. there's less friction in the core hole to jam the core bit. Love the videos guys Looking forward to the stud pack house :)
The end of this video - making do on Sunday evening -brings back sweet memories of house projects with late father in law and my husband. How he LOVED working with his his two sons. RIP Juan, and thanks for the floor, the wall, the doors, the kitchen, and so much more.
I’ve been going back thru the back catalog of vids and Paul has gotten so much better as an on camera personality and Jordan’s video work has improved by leaps and bounds too
there are very few ppl I enjoy watching on youtube and your channel makes the cut. I love this channel. Im a mason with a backround in decorative landscape and this channel is helping me expand my knowledge in construction. Thank you
@nickk4010
Жыл бұрын
So true, one of the few channels that actually show you details where you learn something. It is much appreciated.
@frankdasaintdituri9983
Жыл бұрын
@@nickk4010 👍✅
Love watching this father and son team Great work. I get happy when I see a new stud pack video. Thank you guys for what you do. It's not just that you do great work and the video quality is amazing, but you are both very entertaining.
Last week, I rented exactly the same hammer drill and 4 inch core bit from Home Depot to make two holes in my twelve inches thick foundation wall (fan and dryer). It did such a fine job, I became nostalgic watching this video. Love your channel and it is inspiring me in my home renovations. Cheers from Quebec city!
You should use a 1/4"x 12" or longer SDS Plus bit to pre-drill a pilot hole to assure direct alignment, and then counter-bore from the outside to avoid blow-out. Try holding the drill straight so that you won't end up drilling crooked.
@JohnMiller-ee9pn
Жыл бұрын
That is how I do it, I like the Milwaukee thin wall bits with one of ther cordless hammer drills
After you started the hole you could remove the centering drill. Also, diamond drills don't really like to cut wood, especially after it's been used and the teeth are rounded. They heat really bad. I do HVAC installs in Europe; here almost all the walls are masonry. Not that fun when it comes to drilling. You, guys are awesome!
@cripwellwalsall4700
Жыл бұрын
thats not a diamond drill its tungsten carbide tipped , Dry diamond would have been even quicker
@y00h0011
Жыл бұрын
Ghita... you're exactly right. The Hilti design is good. I hope that Paul reads this because he'll regret it when that bit falls out in a block cell. Gotta remove it before it's to late.
@johnbowser2612
Жыл бұрын
@@cripwellwalsall4700, except through the wood. Wood doesn't treat diamonds well. It closes them up as we like to say. Fortunately, soft materials like concrete will open them back up. We use to use fire brick.
@71sixpak
Жыл бұрын
We use those at work and they are horrible bits. Maybe for block they are ok but in concrete they are the worst. Once the carbide gets a little dull they are junk. And lets not talk hitting rebar. Dry diamond is a much better bit.
@oldtimefarmboy617
Жыл бұрын
He said he was going to leave the first piece of wood inside the hole saw to hold the bit inside of it to prevent it from falling out.
I envy you guys. Any project I did with my dad ended with profanities, threats and 2 weeks of not talking to each other.
@Casmige
Жыл бұрын
This happens whenever my wife asks me to wash the dishes or the clothes...
@chipperkeithmgb
Жыл бұрын
Wish I had got on with my dad
@y00h0011
Жыл бұрын
LOL
@coolHandLuke5150
Жыл бұрын
The good old days
@mattalbrecht7471
Жыл бұрын
Probably the best two weeks of your life..
From a production point of view, I think this is the best to date. You've both come a long way - this is better DIY TV than any other major network. Keep it up.
"You Spin Me Right 'Round" was Dead or Alive, and that sound you just heard was my geriatric soul leaving my body and turning to dust.
You are the one channel I anxiously await each and every new video. I grew up in construction as a part time job in high school and during college summers. I learn something new each video. Keep up the great work.
I love the way you don't take yourselves too seriously. Keep up the good work.
I cannot describe how much it helps when experienced people show their mistakes. Helps me have realistic expectations for myself so much.
I know you probably don't want to hear this but that 3x2 combo WYE used on the urinal should be a 3x2 Tee instead. That combo WYE fitting has the potential to syphon the p-trap in the urinal.
@AquaPeet
Жыл бұрын
And you definitely want the pee trapped (snif snif)
@rogermccaslin5963
Жыл бұрын
Why would that combo cause a siphon? I thought as long as the arm was 2 x the diameter of the pipe all was good.
@MoneyManHolmes
Жыл бұрын
This is why I’m not a plumber. Some of the calculations immediately fry my brain. Nice catch though.
@zebra9398
Жыл бұрын
@@rogermccaslin5963 I'm not the best at explaining things but the bottom of the trap weir shouldn't be higher than the top of the pipe for the vent opening if that makes sense. I'm sure google would have a diagram if you are interested in seeing what I mean.
@akindianhammer945
Жыл бұрын
Combo and or wye 45 are used for vertical to horizontal tee’s should be used for horizontal to vertical.
I do electrical work and I've always wanted to work a project like this. inspiring ✊🏾👍💪🏿
For the humidity you mentioned that would be created from the bathroom, you really should be using aluminum ducting vs using the galvanized duct.
In general you would remove the center bit when the hole is started and you would drill without the hammer function. Enjoy your new core drill
The fitting that should have been used for the urinal is a 2" sanitary tee. The fitting that you used is called a combination fitting. It is used for underground.
I do hvac and I gotta say it was a real treat watching you vent that fan and squeeze that pipe together. Now try putting together 3” 26g 😂
One of many things I love about this channel: the more problems you encounter, the more opportunities to learn. So no matter what happens--easy or hard--it's a win.
Gotta love when a new stud pack vid comes out! Content has come so far over the past few years you guys are the best. Love the format and the story told through the videos. Also I love the attention to detail you guys have but also the ability to recognize when something isn’t worth the extra mile. Real raw content.
Sure have enjoyed watching this set of videos on the project. Watching the stud pack house project in Texas. So when having withdrawal waiting, I go back and watch your earlier videos. Sure love the mental thinking and wisdom that goes into your build projects. Need a video of you guys chilaxing. All work and no play makes Jack a dull boy lol.
We grew up in the 80's and feel it's our duty to tell you the name of the band (for the song Jordan was singing) is Dead or Alive.... Keep up the good work!
You guys to the most. So fun to watch. When he called you Dad, that was epic.🤣🤣🤣
Love how often you guys see posting lately! Thanks, Jordan! Not sure it's a sustainable posting pace for you guys, but enjoying it while it lasts. :)
To save your new core drill/hole saw. Cut a sponge to fit inside, then get the sponge damp, put inside the core drill/hole saw, and then drill.
Great work as always. That hole saw is the next tool that will make it into my toolbox. Getting those plugs out can be a nightmare.
Your content is really amazing and the best on KZread! Thanks for the time y’all put in the channel!
Great job, and on a Sunday! Thank you 👍🏻👍🏻
I've got a few different size hole saws for an SDS Max rotary. I tend to go a bit oversize when drilling the hole for a couple of reasons. First, if there is any mis-alignment when drilling the hole, a bit of wiggle room allows things to line up. Secondly a bit of extra space allows me to squirt in some expanding foam all the way round to insulate and lock in place. Ideally, an exhaust vent will pitch down towards the outside.
Dead or Alive Sings "You Spin Me Round" 1985 Year of the Chicago Bears Superbowl Shuffle.
You guys give the motivation to keep going on my projects!
Pro-tip: temporarily remove the stud to the left of the hole coming from the kitchen sink (at 8:46) in order to drill through the center of studs (to avoid having to notch them), plus this will allow you to feed the pipe through the holes without any joints.
Ahh, what the carpenter buildeth, the plumber teareth apart. 😊
@psilverz4848
Жыл бұрын
fortunately in this case, they're both the same person!
I love that the drill was the star of this video! You guys are great, but that's a fantastic drill!
Concrete block is like cutting through cardboard when compared to the crazy brick in my house. I’ve never seen brick as hard and difficult to cut as mine. Love watching how you work through all these projects.
@oftin_wong
Жыл бұрын
Hot fired ...often the hardest brick has little blobs of melted ceramic looking stuff often black, or dark patches on the brick where extreme temperatures have made the brick super hard ...
@MrKen59
Жыл бұрын
@@oftin_wong that might be it. There are no holes and looks like reddish tan stone to be honest. I hate even drilling a hole for a screw in it.
@oftin_wong
Жыл бұрын
@@MrKen59 one thing I found Which may be helpful Not every hammer drill is equally good ...using my old worn out hammer drill it just won't penetrate but go to the new cams on the new hammer drill ...quality bit...you might have more luck They can just wear out over time
@MrKen59
Жыл бұрын
@@oftin_wong was a fairly new hammer drill. Thanks for the info on the brick. Wonder if there are bits that work better on material like mine. Might need to pay more for a better drill bit that cuts better. When I used the hole saw for my HVAC lines, it was designed to work with a non- hammer drill. It worked, but omg.
@oftin_wong
Жыл бұрын
@@MrKen59 oh yeh it takes forever because it's all on your pressure application Quality masonry bits are better And a new masonry bit is better Than a rounded off one Good luck
Strangely satisfying to glue/fit sections of pipe. Great job guys
Watching the Ezeout eject plugs was like watching an instant replay on TV sports! Go, Canada!
Best project yet! Keep it flowing
I decided to DIY my own dryer vent hole in my concrete block house from1956.... I went with I believe a $65 dollar hammer drill from Harbor Freight and a $70 dollar 4" coring bit from Amazon and with my wife's help had spraying some water to keep the dust down it worked great..... you guys are great for showing us how to do it yourself..... and you know with the cost of labor, not necessarily quality labor I'd rather DIY projects using your help, thumbs up from me....
This project is turning out amazing guys I’m loving this content, it’s damn exciting to see the progress made I just wish there was more content to be watched 😂 keep this kinda stuff up love it fellas!! What are you guys doing for HVAC on this project btw? Beside the fart fans any sort of comfort cooling or heating, I’d like to know in the trade myself?
Again! Your videos are very enjoyable and very very encouraging! I make alignment mistakes and feel really bad, but after this video I will be in good company when I “waller(?)” the hole to get alignment. Thanks for sharing!
Love the new camera work/editing. The switch between you and your dads cams is awesome!
Nice thing about a project like this is that the studs are not going to be holding the roof up and you do not have to worry about shear stresses from wind pressure so those metal plates on the studs will more than make up for how much was removed for the drains and vents.
The damn quality of y’all’s videos have improved so much. You’re getting very comfortable in front of the camera! I love your energy!
Just stumbled across your channel and I'm loving the content guys. I hope you get to start on the new home soon and maybe we will be lucky and you guys start a playlist on the new home rebuild. Congratz on the find and may many years of videos and subscribes come your way.
Supper happy for you guys. Looking forward to framing.
No matter what the project, the highlight is always watching the chemistry between you two.
Having been using various hammer drills for over 50 years. Started out with a used Skill hammer drill that used 7/16" hex shanks. Had a couple of medium size hammer drills that used SDS bits that were always a pain changing out when up on a ladder . Have a Milwaukee for 5/8" & smaller holes and a Black & Decker Old obsolete Macho 2 hammer drill for up to 1& 1/4" spline bits and bigger if I purchased some core bits. I needed a new gear years ago for the Macho 2 & black & decker service center told me that for only a $125 more they would rebuild the hammer drill and give me a warranty. Best money that I ever spent. Now retired a few years and rarely get to use one of my beloved hammer drills. Great vid.
@StudPack
Жыл бұрын
Thx garbo 👍
You really cannot appreciate those hole saws until you've fought with one. Being able to easily eject those wood cores is a really nice feature.
another awesome video guys. love the ingenious ways you figure out how to accomplish the task at hand.
I have learned so much from you guys. I can't wait for the Texas house.
Paul, you're a beast working in the heat. Great content.
Great teamwork guys!
Don’t forget the condensate drain for the tankless hot water heater.... I would’ve done some flashing around the vent....
When you said you were going to “rough in the plumbing” you weren’t kidding.
It’s guys like you that make me a young guy want to be involved in the trades and construction in general love the content only up from here 👏🏽👏🏽
Well the Dynamic Duo never let's us down ... Thx guy's for another great vid ...
Best Father & Son team! Good job Stud Pack!
Your supposed to take the pilot bit out when you have a decent groove started. Some don't even have center bits just centering inserts meant to be removed before through cutting.
I notice the slight twist when sinking the glue joints. You guys do all the tricks, and do them well.
The carbide hole saws (Spyder,Milwaukee,Diablo) drill block like butter! Cores fall out and they are way cheaper than $200! Great content.
In Michigan, the cleanout on the 3” vent would have had to be at the bottom on the 3” stack.
love these guys! I've learned a lot with these guys. Great videos.
You Spin Me Right Round (Like A Record) was by a band called Dead or Alive. 1985
I beg your pardon gentlemen, but i believe you should use a three way wye for sink, p trap left and right with cleanout center.
Like always nice and clean rough out work
Oh hell... I go to Europe for 6 weeks and you guys start another without me! lol I noticed that Jordan is numbering the project episodes now. I was going to suggest that but, he does such a good job already I figured that he'd think of it sooner or later. Smart guy, Jordan. Apparently I need to go back and watch 1 thru 9. And yes.. I've missed you guys. Def. my favorite father/son show. It's like 2022's version of The Courtship of Eddie's Father. j/k Love you guys. And just in case you don't read Ghita's comment, he is correct about removing the pilot bit. You WILL lose it in a block cell some day if you don't remove it after the initial core bit kerf. And he's also correct about wood dulling those teeth. Always best to start with a standard hole saw and then finish with the core bit. BTW.. those teeth can be refitted new. There are tool shops that do it. If you can't find any, let me know, there's a good shop in Ohio. 😄
Great video as always thanks guys!!
no matter what your video is about i always enjoy it!!!! keep it up what you guys are doing is awesome
I did that kind of drilling on my solid 12 inches concrete foundation. It took 30 minutes to drill one hole, but the drill bit is still doing amazing job.
Having the right tools for the job: Priceless
You guys rock. Real American Heroes!!!
We doing some fine woodworking today boy ,has me laughing so freaking hard,GOD BLESS
The correct term in the south is woller it out! Great video!
Really great video! Y’all got y’all’s tools. All of em.
Good job guys!!! Our job is exciting everyday!!!
Great job guys
You guys rock Awesome video thank you for all that great information 👍
Always excited for a new video!
Awesome video look forward to the next one
that hole saw setup looks like it should be operated by a bare chested mountain man holding a chargrilled animal leg.... what a beast of machinery. I do love the eject features of both saws, what a time (and sanity) saver.
Something that I always thought was a brilliant idea was the Colour of the PVA/ABS GLUE that's used in the USA ! It's not the " NORM " here in the UK but I see it as such an advantage & doesn't it assist in QA thus ensuring a Glued Fitting !
Awesome 👏🏽 Awesome 👏🏽 Great work! Best wishes going forward!!
Great job guys keep up the awesome work!!!!!👍👍👍👍
ohandy tip, once the pilot bit makes it's way out the other side of the wall, turn the hammer function off to prevent the brick/block from blowing out
Thank you for sharing!
Good job , and I like the tool links in the description! ❤️
I have a "cookie ejector bit" just like that, it's a Lennox that I bought in Ft. Worth over 20 years ago...
Blow threw with a garden variety 5/8 rotary drill and pack the blowouts with mortar mix
Top notch work fella’s!
Every video leave me wanting more!
Well done Stud Pack!
Great video! Thank you
I really, really like this channel. I do, so much. That being said, perhaps it was the editing, perhaps it was a Sunday, but every step of the work that was explained and done today felt rushed. From the digging out of the stud wood with a hole drill, to the adjustments needed to fit/fix pipes, to the "ah a little blow-out isn't so bad, it'll be covered by the vent housing." because going around outside would've taken more time. It felt like trying to get stuff done on a single Sunday isn't the best way to go about the work. Also I've been reading several "well actually, the plumbing solution should've been x as per code" or "the pipe used for the vent fan was the wrong kind, you'll get leaks", among other comments below. They may not be saying what I said above but their "corrections" or what they felt strongly enough to write in as corrections, says something about how many things caught people's attention. I enjoy this channel, and you guys are super hard workers. Your projects show it. It's just that recently something seems off about the videos. Finally, the subtle nod and shout out to tools and materials has not been unnoticed. That's fine, you have some good tools and you use to show them off in previous years, but the direct method you are doing now is kinda new. Interesting that this increase in shout-outs has coincided with the shorter video format. Advertising pressures? I hope this is just a coincidence. Keep up the great work. I hope you take my comments as constructive and not as a tear-down insult or anything. Be well. -Sterling
I love those coring bits. They’re so helpful. Also if you’re going to work in Texas you need to pronounce words right. We say wallered out. I hate to be the plumbing police but your urinal drain is illegal. You can’t stand a combo up like that on a trap arm or it creates an s trap. Basically of the long down sweep of the combo it makes the water level (weir) of your trap higher than the highest access to the vent. This means it can create a siphon and siphon water out of your trap before it gets to the vent to break the siphon. In the words of Larry haun “that’s the code”. Practically speaking it will work just fine. There’s only one place that am s trap is legal and that’s a toilet. It’s designed to siphon to help it flush better and as the tank fills or the diaphragm resets, it slowly adds water to refilled the trap( bowl). A urinal really works like a mini toilet so if it did siphon, the urinal would replace any water lost.
Lots of work for a relatively small area. But y’all are doing great.
Nice job... your inspiring me to do my own projects