Ive been using strips for 40 years , never knew these functions ! Thanks 😊😊

8-32 is not more "coarse threaded" than 6-32. It's just thicker. The "-32" part _is_ the thread size. Otherwise great video! Thanks!

@paulholmes672

Ай бұрын

You beat me to it. Yes, they are both coarse thread machine screws, having a thread pitch of 32 threads per inch, versus the fine pitch versions at 40 threads per inch. 🙂

@Lethal_Bite

Ай бұрын

To be super theoretical, in a sense 8-32 is actually a finer thread than 6-32. To maintain the same number of threads at a larger diameter, their angle is slightly increased. Like the other comment mentioned, at this size, 32 is coarse and 40 is fine, but at 1/4" 20 is coarse and 28 is fine. 32 would be extra fine.

@DSplatter

Ай бұрын

As @paulholmes672 said, it’s actually thread pitch, not thread size.

@ChrisCogdon

Ай бұрын

@@Lethal_Bite You are technically correct, which is the best kind of correct :)

@Tommy.McLean

Ай бұрын

Thread pitch, not size

This is a fantastic easy to follow. Super comprehensive video. Thank you.

Besides the Milwaukee guy using the wrong way(timestamp:-11:15) to do a proper crimp on the crimp connectors this video was well put together. The pin side of the crimper goes on the flat side of the crimp connector while the wire side of a crimp connector goes on the Crimpers cup side to get a solid crimp on the wire. Otherwise you will get a loose crimp connection and wire can loosen and slip out of the connector overtime especially in any kind of place were there is constant vibration for the connector to deal with. The good thing if you did the crimping the wrong way and find the crimp connection of the connector loose to the wire, then you can always flip the loose crimped wire in the crimper and re-crimp your connector to the wire right way and have a solid well crimped wire altogether for use.

@Petesworkshop2225

Ай бұрын

Ya if you pause on his crimp you can see it's not solid. Great tip!

@chettiarsirusraj9501

Ай бұрын

Try crimping some wire connectors onto wires in person for yourself and then say that you haven't done/seen any crimping in-person so you don't have any idea of bad and good crimping for yourself.

I was 100% sure that I had nothing to learn about a pair of strippers. BUT, I didn't know how the bolt cutters work. I knew they were for cutting those "bolts," but I would never have used them because I figured they would destroy the threads. I never noticed they were actually threaded. I haven't cut many of those screws, but when I have I have gone through the trouble of dragging out the dremel and putting a cutting blade on it and all that. Just pulled my old trusty well-worn Klein Tools stripper out and tried it and it's actually really good. Thanks for teaching an old man something new about a tool I've used for probably thousands of hours.

@curt2742

21 күн бұрын

You've used them for thousands of hours, and in all that time you never thought that they were included on that tool for a reason other than destroying the threads? 'Cause that’s a good business decision for a tool company, and customers would love to have that feature. FFS

This is an awesome tutorial. Well thought out and put together. I will say it's the best one i've seen on wire strippers. Thank you for this video.

I didn't know about the bolt sheer way cool to learn something new and handy . Thank you

Interesting. I would never had thought the little hole was used to put a loop on the end of the wire. I normally just use the tips on mine since they are about the right width to create a perfect loop for most terminal screws on outlets and switches. Well thought out and presented information...probably very helpful for folks who have not done a lot of wiring.

@TerryLawrence001

Ай бұрын

The holes in the "Ears" of the receptacle or switch can be used to make loops as well

@yaboidustin2447

Ай бұрын

I'm more concerned how people didn't figure this out already. I knew every function of wire strippers since I was 8.

@Alan_Edwards

Ай бұрын

@@yaboidustin2447 True and after checking both my pair neither even have that little hole and there are better ways to do that anyway.

@kkfoto

Ай бұрын

I know all these functions because they are written on the tool itself 😆 "loop" "cut insert screws" "crimp" etc

#2 is a crimper. Use them to crimp the little crimp caps or "beans".

@gottliebdee263

Ай бұрын

No, number 2 is an extremely poor excuse for a crimper. Anybody that as ever used a ratchet crimper will agree. They are cheap enough that you can do the job and connection cleanly these days. Any tradesman that comes to me house or business and used that for crimping will get my eyebrows raised.

@BinaryBlueBull

Ай бұрын

@@gottliebdee263 Very true. And what's more than that(*) there isn't actually such a thing as a generic "crimper". Each type of terminal and connector requires a different crimping die to properly crimp and not using the correct one will oftentimes leave you with a weak connection or an otherwise insufficient one, often leading to pull-out, pinched cables, damaged insulation or conductors, arcing, intermittent contact or other shenanigans. I recently bought a proper set which contains a ratcheting crimping tool with interchangeable dies, which covers most of the common types of terminals and connectors. It was quite pricey and contains twelve different sets of dies for fourteen different types of crimp terminals and connectors, each with a significantly different shape. You can tell just by looking at the shapes that they are absolutely not interchangeable, while the crimp terminals themselves oftentimes do look quite similar in shape, especially the part where the crimp is applied (*)You obviously already know this

@barrygillis

Ай бұрын

@@gottliebdee263 So, actually "yeah, but i dont like it" is what you say. Its not great for sure, but if its one of these or some random pliers, or even the good old mangling side cutters, the "cirimper" crimper is brilliant.

@gottliebdee263

Ай бұрын

@@BinaryBlueBull Ah, yes. I'd actually forgotten that point. That said, to get a set that does the red, yellow and blue (ring, but and blade crimps), is well with investing in. They are reasonably universal. Once you get to 10mm2 cable it's a different game

@franklee663

Ай бұрын

Yes it is a cheap crimp, it will be effective for the gauge of the wire that you can strip

I have no plans to strip wires. But now I'm ready.

I've always used that oval tip on the Klein as a wire connection crimper. It wouldn't work well for that on smaller wire, but for the heavier stuff it's fine. Also, I have one of those cheap, stamped steel and plastic auto strippers like the orange and blue one in the background. I think I paid $10 for mine 20 years ago at a state fair and it served me well during my time working in telecomm. Works just like the Knipex you featured.

Thank you sir! I learned a few things.

Here in the UK nearly 50 years ago I bought a tool similar to the Knipex stripper made by Plasplug. Although I don't do much wiring nowadays, when I need to these strippers are still up to the challenge. Nothing fancy just does the job it was designed for which probably explains how it's survived for so long.

Cool!! Been using those for years and had no idea. Speed square is another tool that usually gets used for one purpose but has many.

@Guitarplayer724

Ай бұрын

Unlike the flat-head screwdriver. It has one purpose, but gets used for many. 😂

@jimross898

Ай бұрын

@@Guitarplayer724 I thought the flathead started life as a paint can opener and someone figured out they could make screws.

Great job making the video, excellent tips and tutorial.

This just followed another video i was watching and i am glad it did. i knew most of the functions on those but learned a few, thanks.

Very helpful information for what these special pliers are suppose to do, thanks

Cool video on this type of tool. I knew several of the features already but I wasn't sure what the holes were for that you used to bend loops in the wire. So I am still learning. Unfortunately they make many different types of these type tools and some have even more features and at that point I think it comes down to personal preference. I think I might pick up a new set to keep in my little toolbox in the house.

I knew about the other features, but I had no idea my wire strippers had a bolt cutter! Wow

@eraldylli

Ай бұрын

I had never had a wire stripper with a good bolt cutter. I think its a myth. I go for a mini grinder and small disk usually.

@andrewlacerenza667

Ай бұрын

​@@eraldylliklein tools hybrid strippers cut bolts like butter

@eraldylli

Ай бұрын

@@andrewlacerenza667 Never had the chance to use their products here in Eastern Europe.

@andrewlacerenza667

Ай бұрын

@@eraldylli the Knipex 13718 are very similar minus the crimping feature, but they cut bolts really great too. Highly recommended if in search in the European market.

@stevebabiak6997

Ай бұрын

@@andrewlacerenza667 - Knipex tools are great in the USA too

This was one of the most helpful and informative DIY videos I've watched in a long time. Great job!

Awesome video! I think I'm going to grab a few of the 7in1 milwaukee strippers now thanks to your video's recommendation for them. The EMT pipe reamer will come in very handy

Very nice video. Really helpful. Knipex are on the expensive side of things but they are reliable and you can change it's blades when they become dull.

8-32 and 6-32 screws have the same thread pitch being 32 threads per inch.

6:10 Thanks for showing a failure and then how to fix it I truly appreciate that 😊

I’m just here to tell you how amazing the thumbnail is

@LRN2DIY

Ай бұрын

Haha - thanks, brother. I tested three but one crushed the other two in the test. Great to see you in FL, by the way!

Great video. I didn’t know several of those items

Handyman here. I use both the Milwaukee 7-in-1 and the Klein auto wire stripper, though I cut off the depth stop on the Kleins because it kept loosening. I hear the Irwin auto-strippers are better. I use a Knipex off-set mini bolt cutters as my diagonal pliers. Helps with my elbow, which is prone to inflammation. They've fit in every situation I've needed them to.

@lukecrue1

Ай бұрын

I bought an Irwin auto stripper and it absolutely sucks. Klein and Milwaukee so much better.

@Obtuse94

Ай бұрын

The Irwin auto stop is nearly useless and loosens all the time as well.

@ggrimm79

Ай бұрын

@@Obtuse94 Thanks for the tip, you guys. May have saved me a bad purchase.

@802Garage

Ай бұрын

I have the Klein Tools 11063W automatic strippers. They are like the Knipex shown in the video, but with the form of the Klein he showed. They have individual blade sections for each wire gauge, like the standard wire strippers. So, they are a bit more manual than the completely automatic strippers, but I feel they give the cleanest result for the effort. I use them a lot when doing automotive wiring and they are my go to over an automatic set similar to the ones he showed or over a standard manual stripper.

Thanks! I learned a lot.

Great job explaining dude!

Very curious how the Klein 9 inch combination pliers / wire strippers compare to the Milwaukee 7-and-1.

Great, well presented and pleasant to watch.

I have had those knipex wire strippers for awhile now and use them daily. They are by far the best I’ve used and have not stopped working like all my other versions of universal wire strippers.

@danamcalister

Ай бұрын

Knipex is the best !!! Better than Klein 1,000%

I personally really like my Klein Tools 11063W, which are similar to the Knipex you showed, but in the same form factor as the Klein set you showed. I feel they give a really tidy result even if they take slightly more effort than the other type of automatic strippers. I still go back to the manual strippers when I need to tidy up a strip that didn't go well or I have to take off the smallest amount of insulation. Also, I personally hate the style of crimper included in most wire stripper cutters. That little dimple press makes such a crap connection and I would only ever use it for temporary wiring and testing. A proper pair of ratcheting crimpers or at least one with bigger dies and more surface area is totally worth it.

I always liked my older Cornwell LS series wire strippers. Cutter is on the same portion of the strippers which are below the pivot. The older versions, the non insulated crimper was rounded enough you could use it on insulated terminals as well for an even better crimp without tearing through.

Excellent video! One thing you should have said something about regarding stripping solid wire that applies to stranded also. Nicking the wire causes damage that if the wire is bent, such as pushing it back into a box, the wire could partially or fully break. Even a minor break can cause enough damage that should the wire be fully loaded or repeatedly overloaded, this damage will reduce the wire current carrying capacity and cause local overheating. Bad enough of a nick and it could cause an electrical fire or melt the wire. Replaced many electrical devices that showed signs of overheating, insulation damage or burned wires requiring cutting back the wires. I've seen this done by electricians too! Most common simple mistake!

Thank you for the tutorial. It was very informative. :)

Learned a couple things thanks!

Wow, what a wonderfully helpful video, thank you.

This is great, can you do a similar video but for multimeters?

Very Informative, Thanks. Learnt something Cheers

Amazing cinematography

In Europe we use (used?) more often adjustable wire strippers like the Knipex 11 12 160. Seems not to be available on the US market?

Unbelievable that i have been using these for 30 years and never paid attention to stranded vs non-stranded side of the jaws. Thanks!

I HATE stripping wires with this type of stripper, but this was really helpful! Hopefully I'll remember some of these when I need them. 😂 I'm still using my automatic strippers 99% of the time though!

never knew the cutting screw function. worth watching the video. thanks

Don't twist , it scores a line in the wire. You don't try to cut all the way through the insulation , you just cut the outer sheath and tear the rest of the way. The "wire cutter" blade is a strip gauge , the straight blade is the standard length you strip off the wire, if you need a longer amount stripped you use the holes to consistently get the same length.

@queueeeee9000

Ай бұрын

Can you elaborate on the strip gauge? What holes?

@glennchartrand5411

Ай бұрын

@@queueeeee9000 the length of the blade is the same as the distance you normally strip the wire. If you want to go a longer , and keep it consistent you use the holes as a measurement

@queueeeee9000

Ай бұрын

@@glennchartrand5411 I see. Thanks for replying!

Great video! I agree not to twist when stripping.

Find you a metric pair for the bolt shears... They work great with brass screws. Brass rews are good for 3D prints, you can use them to quickly heat set holes

Great video very pleasant to follow.

4:45 - Using the (uninsulated) ground conductor to determine gauge of the insulated conductors. Be aware that on older "Romex" (NM cable) the ground conductor may be a size smaller than the current carrying conductors. IIRC, the NEC started requiring a full sized ground in the early 70's

those Knipex at the end are ordered and going in my toolbag :)

Thank you, this is a useful video. However, at 11:13 the crimper should go the other way around, with the pin on the flat side of the terminal. The open barrel junction of the terminal needs to be closed by the round side of the crimper rather than opened up by the crimper pin.

Just a suggestion. Use a larger aperture or take the camera out of portrait mode. So little is in focus that it's tough to watch. 🍻

@toxin440

Ай бұрын

yeah - the video, info, and his talking points are all great, the constant shifting in focus/blur though was kind of tough to get through.

On the Milwaukee 6 in 1 strippers you showed. You can use the bolt cutter as a hook bending point and if it’s in the closed position it sort of acts as a depth gauge too.

Can you also use the tip to squeeze across the insulation to split it? In telecom, i used the underside of my diagonal cutters that had a set of teeth similar to the ones at the tip of these strippers in between the handles. I would squeeze the jacket of the solid ground wire, move up a little, squeeze again, and then peel the insulation jacket off and cut it. It could be used in case you need to take a little bit more insulation off of a hooked conductor. Just like you showed that you had a little bit more insulation then you wanted on the wire after hooking it. Split it with the teeth, remove it, and dont need to bend the hook again or cut the wire.

Great video. I learned something new.

I think you might find you can make the reamer bigger with the catch that flips out. Also when the strippers towards the end of video didn’t completely remove the insulation it can be used to twist it neater than if you completely remove it before twisting it?

Amazing video for a simple tool!

Well explained.

Thank you for the information I didn't know that .👍

The needle nose pliers end also fits the knurled rings that hold toggle switches in place in dashboard’s ect. Easy way to tighten or loosen when installing or remove without damaging toggle switches or dash.

Gracias por su estupendo vídeo 👏🏼👏🏼

Those bolt cutter holes are great to use to twist wires together (if both wires fit through it) - much tighter twist, which you can control with tension on handles

Thanks-a-lot!!! I knew of some, but not all of the applications. Great video !

As a novice, thanks for the tutorial.

Interesting, thanks for sharing.

Insulation pulling pliers is the name of the thing behind the needle nose pliers

The "mouse" ears are actually "plaster ears." The "ground" that he used is actually called a bar wire and if it is a grounded wire it is frequently one size smaller than the current carrying conductors. If both bolts have 32 teeth per inch the larger is not coarser. He did not shear the head off, hr cut off the excess bolt. Ron W4BIN

Nice video.Very informative. Crystal clear picture. Thank you for NOT using stupid music and silly theatrics.

#2 is great for "pre cut" wires on new install for Automotive or low voltage. Manufactures pre cut wires and it's easy and fast to "drop in a wire" to the notch. Yeah I work with bionic people that could pull off 4-6 violently barehandly during an install, but with my small gauge wires.

Fun fact the hooks can be made with the ears on the outlets and switches. The gap below the needle-nose I believe is used simply as a wire/jacket puller.

I remember when I was running conduit every day, all day, we chose to use either a pair of channel locks without the dipped handles on, or my favorite, the reamer screwdriver with replaceable die's. I mean you're not stripping wire the same time you're running conduit.

That's a great video dude Thanks a million

When using the Bolt Shears, make sure to thread in from the threaded side. If you thread it in from the other side & cut, you will have difficulty getting the threaded shaft out.

@plutoyaldnil4750

Ай бұрын

The fact that you felt you had to write this worries me lol😂😂😂😂😂

@jimertzman6628

Ай бұрын

You would be surprised what some do

When I make the hook and put it around the terminal, I always squeeze the ends tighter around the screw. Good video!

Great video, thanks!

The only description i could find for the "wire grabber" part was a screw tightener/loosener but it wasnt the exact same set of wire strippers although it was mostly the same style head.

Seems like a cool video maybe try reshooting it with a camera that is in focus and I would be able to watch it

I use the “wire grabber” part to crimp connectors onto the wire, not sure if that’s correct but it gets the job done

Love my Milwaukee wire tool. Been using it for a few years now

I was this old....wow! thanks!

Thank you so much for this! I would have never thought to ask.

SUB'd, thank you for this video...I'd been doing it wrong for years

One favorite trick I use for solid wire is tilt the cutter 30-45 degrees to cut, then straighten it out. This pushes the insulation just a hair, breaking its bond to the wire, making it easy to push off. I also always crimp the wire on screw terminals; if the screw ever backed loose, the wire can't wander off in the box. Never use the push-in holes if you don't absolutely have to.

Good video, thanks.

very well done

Good job 👍

Excellent review. Appreciate your clear voice and absence of unnecessary background music.

Wow, very informative!

As a junior biomed engineer my favorite tool for stripping very small wires (24 awg or smaller) is the black xcellite universal strippers (similar to the kinipex at the end of the video, though I haven't tried that brand). However there is still a limit before it starts to damage the conductors. Starting on a loose (-) setting and gradually tightening until it strips helps. For extremely small wires (30 awg or less) I guess that heated tweezers may be better, but would love to hear from someone with more experience with small wires!

@brodriguez11000

18 күн бұрын

Heated blades in general, but that means a battery to replace.

a single conductor is commonly called THHN (or THWN, THXN, etc). Romex is the brand name for NM-B, or non-metallic, branch circuit cable, and it normally has two or more THHN insulated conductors and a bare ground wire all wrapped together in a plastic sheath.

Nothing beats Knipex 13718

One thing not mentioned is the comfort of the handles. Especially when needing extra force like clipping a small bolt/screw. A lot of these tools have very square profile handles(though usually rubber dipped), rather than rounded. Seems like a lot of hand tool manufacturers put more thought in to the tool end and less in the handle end. Like screw drivers- for some reason, tool makers think that when a person needs a smaller screw driver that it also needs a smaller handle. Like the size of your hand changes when you need a smaller tool. I'm not talking about jewelers tools but just dropping in size from a #3 Phillips to a #1.

still amazed how different electric work is eu to us

When I've used Knipex-style strippers, they've usually pulled off the clear thermoplastic coating off the wire rather than strip the wire.

The crimping technique is the most commonly misunderstood feature on the tool. Not trying to be critical here but the lobe part of the crimp feature aligns with the back side of the split on the terminal. This assures a proper crimp fold and a more secure crimp.

I’ve used the wire grabber to squeeze wire crimp joiners.

Learn something new everyday!

Thank you

The Knipex strippers don't remove the cut insulator on purpose. You can leave the cut insulator over the stranded wires until you are ready to use the wires. The plastic insulator keeps the wire strands from separating and spreading out, leaving them much easier to deal with.

@LRN2DIY

Ай бұрын

Makes sense. Kind of like how many fixtures are sold with the jacket separated but not removed.

@las5073

Ай бұрын

Yeh if I want to land stranded wire on a receptacle without a crimp connector I’ll leave the insulation on the end of the stranded wire and twist it nice and tight, wrap it around the screw on your switch or receptacle and it keeps the stranded wire tight enough to make a tight connection. Works well in a pinch.