Very helpful, encouraging advice! Thanks Brother! 💪

Fantastic advice. I build my 1st 350 turbo hydramatic 25 yrs ago with success. Your advice on homemade tools is wise. 1 thing to emphasize..... be CLEAN CLEAN CLEAN... especially on the valvebody. This is why a metal top work space is important.

Nice family, l love your VDO. Greeting from Bangkok,,,,,,

Great video. And i love your old truck. That baby has character.

1:53 they came out a couple years after I was born, so 40+ years now! I remember my dad had a nearly new 89 Sierra 4x4 ext cab long box (with a 305!) and I always thought 1st gear was so short. Years later I learned it's over 3:1, much deeper than a TH350,400,etc. I haven't done much trans work, but 20+ years ago I put a shift kit in my friends 700 in his 89 IROC. I warned him that it might fishtail easier around corners, especially in the rain 😂

Sounds like your alarm system is beeping 😂 as a cable guy, I hear that in a lot of homes.

Whoops, disregard, I located the link you shared in other replies. Thank You Sir

Really enjoyed your video!

Great information and a fantastic presentation. Thank you sir.

@carcobbler

9 ай бұрын

Thanks Rick.

good detailed video thank you

Use the old trans fluid or heating oil for the shop. Or bring it to a recycling center.

Im interested in that pdf i I just got 84 k10 with tranny issues got 2 700r4 s so hopefully I can fix one maybe both for a backup or next project. Your information is priceless and I will be following your channel. How can I get the pdf.

How do i get your 700r4 pdf? Love your videos. Just found them. And looking to rebuild a 700r4 for my own ls swap. Thankz

it cost me 1100 dollars just in parts to rebuild a 4l60e, but I know it will last a long time..some high quality snap ring pliers are a must.... a clean working area, and a case of brakeclean... I pressure wash the case of the trans before disassembling.. if u send your trans out to a shop, u never know what u will get.. trans shops end up with alot of spare parts and im sure they are tempted to put used, questionable parts in the rebuilds.. the fact that most trans shops off a very short warranty, tell you they arent really rebuilding them, they are freshing them up and cleaning them.

@carcobbler

10 ай бұрын

What you say is so true, I like the peace of mind that comes with knowing its done well, and when something goes wrong I have no one to blame :)

@Sabe53

2 ай бұрын

@@carcobbler Plastic spacer is a nylon bushing, you want, NEED it in there.

@carcobbler

2 ай бұрын

@@Sabe53 thanks, I didn’t take any chances, opened they tranny again and put the bushing in where it belongs.

@Sabe53

2 ай бұрын

@@carcobbler Yea a roller bearing would be better than that nylon thingy but with out it your metal on metal.

How long have you been building transmission?

@carcobbler

2 ай бұрын

First one was to years ago but I’ve only done about 6 :)

Can I get the manual please.

@carcobbler

7 ай бұрын

www.uscars.biz/uscars/extras-documents/ATRA_GM_4L60-4L60E_%28700R4%29_Rebuild_Procedures.pdf

Can I get the manual please?

@carcobbler

10 ай бұрын

Here’s the one I use: www.uscars.biz/uscars/extras-documents/ATRA_GM_4L60-4L60E_%28700R4%29_Rebuild_Procedures.pdf

@papergatorzfedducca7998

10 ай бұрын

@@carcobbler thank you!!!🔥🔥🔥🔥

@papergatorzfedducca7998

10 ай бұрын

@@carcobblernew subscriber!!!

@dougedwards8022

9 ай бұрын

A NV 4500 is a excellent 5spd manual transmission 😆😆

good video but that beeping in the background is so annoying

@carcobbler

9 ай бұрын

Thanks for watching. Maybe the beep has something to do with you are watching on. I can’t hear a beep at all.

@MyLifeThai371

2 ай бұрын

I don't hear any beep on the video.