Gotta tell you buddy...I've rebuilt several transmissions for people and a few for my own vehicles that's saved me a ton of money and has gave me much pride and some enjoyment in doing the jobs myself but I owe it all to good people like you that has taken the time to walk us through it and back on the road happy ...we couldn't do this so easily without you so thankyou thankyou and much respect and wish you well ..keep the videos coming because you help more people like myself than you know...

@GaryFerraro

2 ай бұрын

Thank you

Hey mate, that is awesome. you have saved me so many issues and made my rebuild so easy. Once again thank you

Thankful for you posting this tear down. Excellent work!

Thank u sir for all ur videos it has been really helpful to me🙏🙏

Thank you very much... For showing all the parts in details sir... Will contact you in future if any help required.

@GaryFerraro

4 жыл бұрын

Rakesh Bharadwaj ok. Any questions just let me know

Got one of these on a 2011 equinox 2.4l AWD. Is a little slow on the change from 2nd to 3rd. Occasionally, during this shift, the RPMs will shoot up. Seems to work better after it has warmed up. Is this a common problem with a common solution? About 120k mi, fluid is dark. All the other shifts feel fine.

Thanks for the video. My wife's 2012 Chevy Malibu jerked and refused to shift into 3rd. The code was P07bf (Input speed sensor low voltage). I purchased the part, thinking it would be an easy fix. Ended up tearing apart the trans. I was wrapping it up for the night and found a couple plastic pieces under the car that I hadn't heard fall. This video helped me identify the parts and locations. In the morning, I'm going to finish my project. Hopefully, it'll be done raining by then.

@GaryFerraro

3 жыл бұрын

sounds good, my e-mail is gsferraro@yahoo.com if you need to send any pictures

@TrentBigW

3 жыл бұрын

@@GaryFerraro I broke it. I reconnected everything the same way as I took it apart. Now, the output sensor is coding. The ECM isn't communicating. And R,N, and D are all drive (low power), and the optional Manual mode is Neutral. Please HELP. I'm 4 hours from home and going to miss a lot of work if I don't get this repaired fast.

@GaryFerraro

3 жыл бұрын

Are you sure you hooked up manual valve correctly. What did you break

@TrentBigW

3 жыл бұрын

@@GaryFerraro I'm going to send you an email.

@GaryFerraro

3 жыл бұрын

Ok. I’m out but will be home in about an hour

It is easy to see why the trans needed fixing with that "engine oil" in it. I have a 2012 Holden Cruze which I have only had for a couple of years and it was quite jerky and clunky so I got the transmission serviced. A lot better afterwards and I have just done another fluid change. Shifting like a new one now thankfully. The old fluid had done 90,000 ks so it was past due. Hopefully never have to pull the trans apart in my lifetime but handy to know how it fits together anyway. Thanks

Hi Gary, Just wondering if you have a full video on the 6F50? 2011 mazda tribute, destroyed 1,2 planetary ring gear and planets. Would you replace valve body when severe contamination exists? or can you clean and reinstall?

@GaryFerraro

7 жыл бұрын

I have a teardown video on the 6F50N, I would change the solenoid pack, with that amount of damamge, make sure all the valves are free in the valvebody

I have a question for you, I'm working on a 2011 Cruze. My understanding is they made some changes to the 6T40 in 2012 and any 6T40 2012 and up would not be interchangeable. Are there any other vehicles prior to 2012 that would work in the 2011 Cruze?

@anthonyjulson8840

3 жыл бұрын

It's my understanding that in a 2011 you have to use a 2011, same goes for the 2012. After 2012 you can interchange.

well I just rebuilt the trans and now I'm doing the motor and was just wondering if I did everything right since I still have the trans out of there was something wrong now would be the time to find out lol

I have a 6t45 transmission out of a 2014 Chevy Malibu it brings up to codes before going into limp mode P0700 and P07BF and P0716 I have changed inner and output speed sensor when it first starts up it drives prefect then when it heats up it goes into limp mode change fluids still does the same thing when it sits for a while the check engine goes out then when it heats up limp mode check engine light comes on what do you think is wrong with this thing and also when it goes into limp it shifts really hard and then it wont go in to manual it only drives in second or maybe third

My car is a Daewoo Lacetti Premier 2009 (a Chevy Cruze with the Daewoo logo). I want to install an extra automatic transmission fluid cooler, but I want to know which of the ATF cooling lines entering the radiator is the inlet? There are two lines attached to the radiator. So which one is with the fluid leaving the transmission and entering the radiator? Is it the bottom one “as usual” or the top? Because all I know is that the inlet is the lower line in order to push the air out of the radiator. Please help me with this.

Hi, Gary. Great video! I have a problem with my 2013 sonic's 6T30. Shift between 1st and 2nd gears vice versa is smooth but it wont go to 3rd gear. When in 2nd gear and the RPM goes past 2000, it wont shift, instead it is as seems like hitting acc pedal (RPM keeps going up) but at the same time pressing clutch pedal as if in manual trans. And it will shift back to 2nd gear. And it would stay there no matter how high the RPM gets. Checked the fluid and filter and had them replaced. Checked the internal. But still fruitless.

this man is a GENIUS

Excellent video, I have a question on these transmissions. I have a 2012 Chevy cruze with a 2czw build,the torque converter won't spin and had to pull engine with trans ,seemed like engine was locked up but it's the trans. I have a known good trans from a 2014 cruze which is a 4bks , can I just change the techm from the 2czw to the known good trans 4bks or are there fundamental differences? Thanks

@jesusmfelix-fu4qz

5 жыл бұрын

Did you ever try it im trying to see if i can so the same with a malibu trans into an equinox by changing the techm they looks exactly the same to me

Could you swap a 6T40 from a 4T45? I have a 2007 Pontiac G6, nothing is wrong with my car, but I saw that the 2010 models had a 6 speed trans with the base 2.4L engine. I have the base engine but with a 4 speed trans

I have a 2014 Chevy Captiva Sport(rebadged Saturn Vue) and the thing I question is it rattles like it is in the wrong gear. Like a manual transmission if you try to take off in too high a gear. I am driving at a cruising speed and when I accelerate it rattles instead of dropping to a lower gear. Thoughts?

@GaryFerraro

7 жыл бұрын

Does this start off in 1st gear and upshift? Any difference on how the trans works when the car is cold to when its hot? Any codes present?

Is the 6T70 heavier duty?

What sealant do you use when re-assembling?

@GaryFerraro

5 жыл бұрын

i use regular black silicone

Hi Gary, I recently assembled a 6T45 GEN1 after a 3 5 Reverse wave plate failure. I assembled it with the updated 3 5 Reverse clutch drum and wave plate saver steel, new steels, wear plates, pistons, rebuilt the pressure sensors in the TCM and fitted a Sonax kit to the valve body. On the test drive it shifted well in all gears for 10 minutes after I reset the shift adaption but I didn't load the transmission up to that point. I was rolling slowly in second gear about to make a left turn at an intersection and applied about half throttle to load the transmission up. Something inside the transmission felt like it let go while in second gear and afterwards, had very little drive in all gears with slippage. Also, the park prawl stopped working. Shifting from D or R into P, a clicking sound could be heard like the prawl was just contacting but not enough to engage. Initially I thought the Snap Ring in the bottom of the case that holds the 2 6 piston return spring popped out of its groove as the problem occurred while in 2nd gear but no, its still in place (it was very difficult to install in the case groove). And maybe the rotating assembly had moved upwards somehow and made the prawl not engage. After disassembly I cant see what the problem is. All snap rings are in place and I cant see any damage to the case or any metal shavings. Could this happen if the updated clutch drum has the older version piston fitted? If so how would that effect the park prawl or maybe that is another problem? Thanks for any advice. Stu

@GaryFerraro

4 жыл бұрын

Did you by chance disconnect the linkage at the trans to see if it will go into park, was reverse ok? and did drive engage ok? any codes show up

@orange44number

4 жыл бұрын

Awesome video Gary and check this video out Ripahh. I think you're right about the updated clutch drum having a different piston.

@Ripahh

4 жыл бұрын

Gary Ferraro I found one of the 2nd gear steels was fitted incorrectly. In the pump case is a small seal that goes to a black plastic piece. It was on the wrong side as another problem. The box now has gears and all is working but it is harsh on 4th to 3rd downshift. I will reset the TCM through TIS and see how it goes next week when I’m back from work. It would be awesome to all of us home transmission repairers if you could upload an assembly video! Thanks mate

@GaryFerraro

4 жыл бұрын

@@Ripahh ok, I will keep that in mind

@Ripahh

4 жыл бұрын

Gary Ferraro after the TCM reset the 4-3 downshift felt like it was slipping and vibrating but after a few times it came good and is now great. Taking the trans out of a AWD Diesel Chevrolet (Holden) Capitiva is a nightmare without a hoist but the second time around is faster. I hope I don’t have to take it out again! Cheers

Please tell me , where is the VSS located? I know the input and output speed sensors, but where is the VSS (the speed couter's sensor)?

@jilarioviedo

3 жыл бұрын

Sir it’s been 2 years trust me delete the comment

@TheKhwailed

3 жыл бұрын

@@jilarioviedo LOL I already replaced it and solved the problem.

I keep getting a P0723 and a P0501 which points to the Output Speed Sensor. Is it likely to be this sensor it would it be the TCM failing. The transmission shifts fine until this code puts it in limp mode. Fault only occurs after 1hr + of driving. Fluid clean and at correct level. Any help appreciated.

@GaryFerraro

5 жыл бұрын

Whats the year make and model of the car?

@killawattgarage

5 жыл бұрын

@@GaryFerraro 2010 Cruze with the 1.8 petrol engine F18D4

Great video, I would love to see a followup of a 6T40 being rebuilt from the torn down state you had this one in at the end.

@GaryFerraro

6 жыл бұрын

Will keep that in mind when the next one comes in

@yvettec.5706

5 жыл бұрын

@@GaryFerraro whats a fair price to rebuild the 6T40?

@GaryFerraro

5 жыл бұрын

@@yvettec.5706 With a new TCM, around 3300.00

Love this video my 2012 cruz has this problem 1 and 2 just fine no reverse no 3rd

@GaryFerraro

6 жыл бұрын

very common issue. the wave steel breaks up and tears up the drum and seals. where are you located?

@anthonykraft2186

6 жыл бұрын

Southeast mo

@GaryFerraro

6 жыл бұрын

ok, i dont know anyone there, im in new york

@anthonykraft2186

6 жыл бұрын

I think im gonna try it im torn i can get a reman from chevy 2200

@GaryFerraro

6 жыл бұрын

Thats not a bad price, can you do the install?

Do you have to have a re-flash done after repairs are done on the transmission?

@GaryFerraro

5 жыл бұрын

Mike Wilson you can do a shift adapt reset but not really a reflash

Great video! I have a 2011 Malibu broke down right now, just waiting on some parts. Had a snap ring & 3-5-R wave plate break and jam up in some parts. I ordered a reaction planet due to gears being chewed up, but the flanges (the 3 flanges with 8 fingers on each) were longer than the one I have and there are more holes. Will this matter? What measurements matter in this case? Also, where do you order/buy your transmission parts from? Thanks

@GaryFerraro

7 жыл бұрын

When you say flanges, do you mean the clutch hubs?

@GaryFerraro

7 жыл бұрын

Where are you located?

@debeckhenryessien6639

5 жыл бұрын

thanks for the video but please i have one question. can the same spec of cruze 2011 made in korea complete gear box replaced with american made spec?

Doesn't forcing screwdrivers in the joint damage the sealing surface? Thanks for the video.

@GaryFerraro

7 жыл бұрын

If your not careful it sure can, mine went ok. Thanks for watching

@amtpdb1

7 жыл бұрын

Gary Ferraro Thanks for replying.

@GaryFerraro

7 жыл бұрын

Thanks for watching, please subscribe

@jimbo251987

6 жыл бұрын

Gary Ferraro have a good diagram or assembly video on this trans?

Hello Gary, I have a 2011 equinox 4 cyl fwd that has a bad transmission. I took it to the transmission shop and they quoted me around $4k to rebuild it and install a few upgraded components. I can purchase a reman trans for $2k and try to put it in myself. Is this a viable option? Is there any programming that needs to be done? Thanks

@GaryFerraro

5 жыл бұрын

Not a bad price for a reman, i'm thinking it will need to be programmed. There are people out there that do mobile programming. Do you know anyone that works at a repair shop?

Good video. I am working on my first of these. (Same waved plate broke and the snap ring popped out.) Putting it together, my input sun gear has what are apparent directional markings. The one mark is on the inside recess of on one side of the gear and also there is a narrow groove nearer one end of the gear, on the teeth themselves. Is there an up or down on these input sun gears?

@GaryFerraro

6 жыл бұрын

Is the recess the same on both sides?

@manfredknight5014

6 жыл бұрын

Yes, I measured the depth of the recesses and they are the same. This is a 2010 Equinox 4cyl, btw.

@GaryFerraro

6 жыл бұрын

I checked my manual, it doesnt specify it goes a certain way. Sorry for late reply, shop is packed

@manfredknight5014

6 жыл бұрын

Thanks for all your responses, Gary. I didn't find any other information on the sun gear being directional in AllData or otherwise, but it helps to have someone verify it, nonetheless. I'll be putting the case halves together this morning.

I live in chicago south side. Thank you I just was hoping you knew of something where the training was very good...

@GaryFerraro

3 жыл бұрын

There is a company in Miami called ATSG(Automatic Transmission Service Group) not sure what they offer as far as training

Is it cheaper to rebuild a transmission or just buy a used one??

@GaryFerraro

5 жыл бұрын

That's something to research, I have had it where the rebuilt and used unit were very close in price, with in a couple of hundred

What is the trick on re-assembling the 2-6 piston assembly, I've compressed the return spring as the illustrated in the manual but the snap ring doesn't lock in place?

@GaryFerraro

5 жыл бұрын

That return spring may have to go a certain way, then i take a screw driver and lightly tap the snap ring in place

@mikewilson4622

5 жыл бұрын

@@GaryFerraro Thanks for the reply, today went into work to get r done and the snap ring went right together versus other times trying. But thanks again.

@GaryFerraro

5 жыл бұрын

@@mikewilson4622 Great, glad it worked out

I have the same transmission 6t40 with the same damage, the drum. When Assembly the clutch everything is free. until I install the retainer ring everything locks up I have double checked Everything seem to be correct. Any idea of what could be the course. Thank you in advance

@felixteresa7584

3 жыл бұрын

Transmission is in neutral

Do you know if you can get the green and yellow speed sensor connectors? The lock tab broke on mine. I don't wanna buy the whole sensor.

@GaryFerraro

2 жыл бұрын

As far as i know you cannot, i don't think they are that pricey

What tests are made before re installation of transmission?

@GaryFerraro

5 жыл бұрын

I air check the unit before i button it up

I have a 2011 cruze with the 6t40. It goes from 1st to 2nd a little rough and has a huge delay into all the rest of the gears. It will rev freely between the shifts then finally completes the shift. Reverse also takes about 4-5 seconds to engage. This all started with an occasional extremely hard downshift from 6th to 5th. Any ideas?

@GaryFerraro

5 жыл бұрын

Robert 3 Sounds like the 3-5/reverse drum may be on its way out. The wave steel likes to brake.

@Robert-dc1ws

5 жыл бұрын

@@GaryFerraro Thanks for replying so quickly.

@GaryFerraro

5 жыл бұрын

Robert 3 welcome. Very common problem to loose 3rd 5th and reverse.

I have a chevy malibu 2013 lost forward and reverse.. I used additives and that fixed the problem a bit for a while but now is bad again.. Any idea what would be the problem??

@GaryFerraro

Жыл бұрын

does this stop moving hot?

If I do have to replace the transmission in my 2011 equinox 2.4L AWD, can I use any trans from 2011 up that connected to the 2.4L?

@GaryFerraro

4 жыл бұрын

There are different generations with these transmissions, if your going with a used one, give the yard your vin number

@rickwest2818

4 жыл бұрын

@@GaryFerraro ok, thanks.

What do you think would cause this transmission to jerk a little when being put into drive when cold? Seems to go away when warm. Maybe an engine issue? 2011 Malibu 6T40 with 120k miles on it. It has been flushed at the dealer before.

@GaryFerraro

6 жыл бұрын

Is the engine idling higher than normal when cold? that can cause to seem like a harsh engagement

@DJR5280

6 жыл бұрын

Gary Ferraro The RPMs may be slightly higher than idle but it still jerks into gear. Seems to go away a lot when the car and transmission is warmed up. I should note that it seems like it still jerks sometimes even when warmed up. I just hope the transmission doesn't break. I'm taking into the dealer this weekend to have it flushed. They use a BG machine

@dominickbitsui9596

6 жыл бұрын

You need to make sure you have enough transmission fluid.

@DJR5280

6 жыл бұрын

Dominick Bitsui Had it flushed and trans fluid level checked. The issue comes and goes to this day. Don't know what to do.

please give your Opinion how do you remember all these stuff how to re-assemble? on every Transmission do you also follow some Instructional Paper/Book?

@GaryFerraro

7 жыл бұрын

Im rebuilding for years, but when i get a new trans on the bench, i do try to get a manual, there is a company in Miami called ATSG they put out very good manuals for transmissions

@MuhammadAli-su3oo

7 жыл бұрын

Thank you dear Gary I'm from Pakistan, you KZread guys are so much helping us.

@GaryFerraro

7 жыл бұрын

Greetings from New York

Hey I got a 2012 sonic that’s getting the 6T30 trans rebuilt now at 80k. What frequency would you recommend changing fluid in it? I’ve heard ever 45k? Thank you !

@GaryFerraro

4 жыл бұрын

You can only do drain and fill, depending how much you drive i would do it every year to year and half

@Tiger9535

4 жыл бұрын

Gary Ferraro thank you. I think when I got the trans flushed it screwed it up big time. I already had a problem with 2-3 slipping when it got hot. Probably one of my biggest mistakes haha

@GaryFerraro

4 жыл бұрын

@@Tiger9535 What is it doing now? how is reverse?

@Tiger9535

4 жыл бұрын

Gary Ferraro it’s in the shop now getting rebuilt I barely made it to the shop it was flaring RPMs so bad. Reverse was fine it just didn’t like shifting when it got hot

@MrLoony690

2 жыл бұрын

@@GaryFerraro so you would not recommend doing a full transmission flush on the 6T30 only drain and fill? This trans takes about 8qts of fluid correct? Thanks looking to change fluid here soon after the rebuild got about 7000 miles on the rebuilt unit.

Hi there a question my 2011 Chevy Malibu shift's normal but once it shift's into 5th gear it shift's hard what's the cause of that ?

@RC_BASSBOY

2 ай бұрын

@GaryFerraro Sent this a year ago lol this is what its doing.

Transtar's rebuild kit with the steel plates do not line up, Do you ever have to file them to fit?

@GaryFerraro

5 жыл бұрын

i never had to do that, they may go in ore than one way

@mikewilson4622

5 жыл бұрын

@@GaryFerraro I took the them back to transtar and compared them with another 6t40 kit and determined they are a manufacture defect they lack one more notch versus the old. So I need to find someone that sells the steels separately and hopefully are right.

No filter to this transmission?

Great resource for all us DIYers out here, thanks. At about 22:45 you take out the drum and on the bottom side of it, that snap ring is out and the piece that the snap ring holds in is thus loose (I think you called it a 'sim support'). Same exact issue here, how do you get that snap ring back in there it looks like there is not enough clearance? Also, do you know the intent of the 'sim support' and the snap ring that holdsit in?

@orange44number

4 жыл бұрын

I correct myself, that may not be a "Drum", I cant hear what it is.

@GaryFerraro

4 жыл бұрын

@@orange44number That is the Center Support, the snap ring I speaking of holds the return spring for the piston in place

@orange44number

4 жыл бұрын

@@GaryFerraro Thanks you

@GaryFerraro

4 жыл бұрын

Welcome

Ledison From Brazil good Job

@GaryFerraro

7 жыл бұрын

Thank you

How much would you charge to do a 6t30? I need the pump filter replaced and pretty much a general rebuild of whatever is broken. It shifts fine but the pump whines because the filter is clogged so its probably gonna kill my clutches and bearings.

@GaryFerraro

4 жыл бұрын

What is the year, make and model of your car, engine size too please

@tidalnebula9329

4 жыл бұрын

@@GaryFerraro 2013 Chevy Sonic hatchback 1.8l it has 200,890 miles

@GaryFerraro

4 жыл бұрын

@@tidalnebula9329 ok, I will check and get back to you, are you in the New York Area?

@tidalnebula9329

4 жыл бұрын

@@GaryFerraro lol no but I always get over charged here and I am looking into options. I live in Kentucky. It's my daily driver and it's definitely an issue that will boil over sooner or later

@GaryFerraro

4 жыл бұрын

@@tidalnebula9329 Honestly, in my area I would get between 3000 and 3300 that is with a new TCM and programming also

Speed sensor can be service on equinox?

@GaryFerraro

5 жыл бұрын

if it's a 6t40 yes, what code are you getting?

atsg manual shows dots on pump gear assembly , but mine does not have them I'm not seeing a wrong way to put this back together besides the beveled side being in the wrong position. My service manual shows no dots either for pontiac G6 2010.

@GaryFerraro

5 жыл бұрын

Look at where the converter rides on the inside of the gear, may be a witness mark.

@mikewilson4622

5 жыл бұрын

@@GaryFerraro I'm not seeing any marks like you mentioned that would indicate any timing marks between the pump gear and the driven gear. The thing I notice is the beveled sides of each component , which are faced toward the pump assembly. Have you ever experienced this?

Where do you get your rebuild kit from?

@GaryFerraro

3 жыл бұрын

I purchase from Transtar, are you rebuilding a 6T40?

Best way to get this out of the car?

Awesome video Gary! I'm a gm transmission technician at the dealership, seems they haven't solved this problem still, have you worked on any gen 3 6t40 transmissions yet?

@GaryFerraro

3 жыл бұрын

Not yet, What are you seeing fail on these units?

@devinbellis9898

3 жыл бұрын

@@GaryFerraro very few stop start accumulators, in the beginning especially on cadillac the coolers will fail and cause intermix issues. Lately though failed pumps that end up causing 3,5,R steel plates to chew up the drum, steel plates are very thick and tough. Also seen some piston failure 2-6 and 1,2,3,4. And lastly the front cv axles may cause an odd vibration/ shudder feeling during acceleration between 20-40mph

@GaryFerraro

3 жыл бұрын

@@devinbellis9898 Thank you for the info, Have a 2015 6T45 on the bench now, going to teardown in the morning

I have a 2011 equinox with a 6t40 in it. Just bought it off a friend and he's saying the dealership told him its got a bad tcm. It drives perfectly fine until the car is warm and then it will go into a limp mode where the car takes an extremely long time to accelerate. Does this sound like its actually a bad tcm or does it sound like a different issue? Ive been hearing the 3-5-R wave plate is the most common issue with these transmissions

@GaryFerraro

4 жыл бұрын

Can you tell me if any codes are present for the transmission? Does the car stop moving when hot?

@hankhasemeier6887

4 жыл бұрын

@@GaryFerraro I can check for codes later today or tomorrow. It doesn't stop moving. I can maintain whatever speed I am at. Or if I am starting from a completely stop it will move but takes a very very long time to accelerate. Rpms won't go past about 2200 no matter my throttle input

@GaryFerraro

4 жыл бұрын

@@hankhasemeier6887 It's like no response from gas pedal? let me know the codes

@hankhasemeier6887

4 жыл бұрын

@@GaryFerraro there is a response from the gas pedal. Full throttle will run the rpms up to about 2000 but no higher. Then the car will accelerate just extremely slowly. I can get it up to whatever speed i would like to as long as I have the patience to get it there no hard shifting or anything else noticeable and reverse works just fine. Wasn't able to get a code reader on it as the auto shop close to me is only taking appointments due to covid

Sonex makes a kit that contains a new wave steel and concave plate that mates together . No internal splines on the new wave plate, so it doesn't dig in the damaged part from the old wave. End play comes out perfect.

@GaryFerraro

3 жыл бұрын

Will check it out, thanks

Hi there great video. Is it possible to change the output shaft speed sensor while the trans is in the car? My speedo is erratic and was told to change the output speed sensor by the dealer. Thanks

@GaryFerraro

6 жыл бұрын

Yes, you have to remove the tcm/valvebody, its located behind that

@westside403canada6

6 жыл бұрын

Gary Ferraro okay thank you. I've done the timing chain on this vehicle also...Is it something I should be able to handle?

@GaryFerraro

6 жыл бұрын

Should be, you may have to take the tcm off first and then the valvebody, make sure the manual valve is hooked back up and do not over tighten the valvebody or tcm, should be around 95 inch pounds

@westside403canada6

6 жыл бұрын

Gary Ferraro okay great! Thanks so much for the help!

@GaryFerraro

6 жыл бұрын

no problem

Hi Gary, great video. I have a 2011 1.4 Cruze automatic(6T40) with 40k KM. The AFT fluid was changed last year, no burnt smell. Got the code-"P0776 Pressure Control Solenoid Valve 2 Stuck Off". I was thinking of replacing the solenoid valve myself. Could there be mechanical damage also? There is no rattling noise , I only have gears 1 and 2. Any way to know if I have Gen1 or Gen2 Solenoid Valve without opening the transmission. Thanks

@GaryFerraro

2 жыл бұрын

2011 Should be Gen 1. what happens when it should shift to 3rd? does it neutralize? how is reverse?

@frankp329

2 жыл бұрын

@@GaryFerraro it will not go into 3rd and there is no reverse. Tks

@GaryFerraro

2 жыл бұрын

@@frankp329 ok, Your 3-5/rev wave steel broke and took the drum out, solenoidwill not fix problem

@frankp329

2 жыл бұрын

@@GaryFerraro Thanks Gary for your help.

Really liked your video. I'm a builder as well but I have not worked for a big shop in a while as I have a small warehouse I work out of with mainly word of mouth business so I see mostly the common 4l60 4l80 etc not to many newer ones yet. I do build a lot of Hondas and Volkwagens as a lot of builders don't like to mess with those, but just like anything else you have to spend a little time to figure out what makes them tick. As we both know the valve bodies are the main culprit most of the time so I have a big investment in Sonnax tools but it's worth it as the unit is installed once and delivered. I have built a small amount of the 6t70s with the broken wave plate but I have my first 6t45 and was just curious and that's why I watched the video to see what to expect. Pretty much the same as I expected, also I'm assuming those have the same issues in the techm with the pressure switch disc's failing so I know I'll be changing those as well. The video is a little long though could edit the tear down parts with all the bolts to condense it a little but all in all very well done Sir, nice pace on the explanation of tear down etc.

@GaryFerraro

6 жыл бұрын

Thanks for watching, where are you located?

@BuiltRiteTrans

6 жыл бұрын

Gary Ferraro St. Augustine FL

@GaryFerraro

6 жыл бұрын

Nice to meet you Bruce, Greetings from New York

Is it possible to get the transmission out of a 2015 malibu without removing the engine to replace it.

@GaryFerraro

5 жыл бұрын

Sure, that should be possible

@siktwistofFATE89

5 жыл бұрын

@@GaryFerraro that would be awesome i just dont want to dismantle everything the transmssion is bad enough

Hello just wanted to ask if you know if you can use a chevy malibu in a chevy equinox by changing the techm they look the same to me

@GaryFerraro

5 жыл бұрын

What years are the vehicles?

@jesusmfelix-fu4qz

5 жыл бұрын

@@GaryFerraro the vehicle is a 2010 equinox with 2.4 ecotec and the transmission is from a 2012 chevy malibu i know they wont interchange but to me they look exactly the same mabe changing the trasmission computer?

@GaryFerraro

5 жыл бұрын

@@jesusmfelix-fu4qz Whats the problem with the trans? any codes?

@jesusmfelix-fu4qz

5 жыл бұрын

There are no codes it takes a couple seconds to catch reverse and it slips a little going into 3th gear

@jesusmfelix-fu4qz

5 жыл бұрын

Im going to try a different transmission to see if it works by changing the techm ill let you know what happens

I was driving my.malibu 2011 and i heard a metallic gear noise, when i stopped at traffic light the car wouldnt shift in 1st or reverse. Any clue? Its a 6t40

@GaryFerraro

4 жыл бұрын

If you let it cool down, does it move?

@rodrigomeca

4 жыл бұрын

@@GaryFerraro yes, after cool dow it works perfectly, no check engine light, thank you for answering

@GaryFerraro

4 жыл бұрын

@@rodrigomeca what going on here is your filter is clogging up because something is probably coming apart. Filter is internal to the trans, so trans will have to come out

Is this transmission reliable? How long does it run?

@GaryFerraro

10 ай бұрын

we see these come in around 80 to 100K miles

@user-mo4kw6wq2z

10 ай бұрын

​@@GaryFerrarothanks sir. it's so sad to see gm and ford just going down in terms of just everything including reliability

What does a rebuild cost and why is this unit more reliable than the 6F35?

@GaryFerraro

6 жыл бұрын

Rebuild on these is around 3000, this is because the TCM usually has to be changed. Did i say its more reliable?

@DJR5280

6 жыл бұрын

Gary Ferraro No you didn't say that but the 6F35 seems like a nightmare in terms of reliability vs this. Plenty of 6F35 horror stories.

@GaryFerraro

6 жыл бұрын

The 6T40 has issues where the 3-5-reverse wave steel breaks, you dont really see this on the 6F35, this unit has problem with the foward piston tearing causing a delay in drive, but honestly i do alot more of the 6T40 units than the fords

@DJR5280

6 жыл бұрын

Gary Ferraro Interesting, okay thank you foe the response and video.

Whats the differrnce between 6t40,45 and 50

@GaryFerraro

4 жыл бұрын

Usually the torque rating, there are different generations though, Gen 1 is not interchangeable with a Gen2

Thank you so much. I wasn't able to find a source for a definitive answer on the transmission filter question if it actually had a end user replaceable filter.

@GaryFerraro

5 жыл бұрын

TK6214 what was the question?

@TK6214

5 жыл бұрын

@@GaryFerraro if it actually had a end user replaceable filter.

@GaryFerraro

5 жыл бұрын

@@TK6214 Is that like a cooler return filter?

@TK6214

5 жыл бұрын

@@GaryFerraro some transmissions have a filter the customer can swap out but this one isn't the case. there was a huge debate on the sonic owners forum about this. but your video answered it.

@GaryFerraro

5 жыл бұрын

@@TK6214 internal filter

Looks in a way easier to rebuild than a 4380e. Probably the hardest part is getting it out of the car. Same trans as in my 2012 cruze. has 224000 miles might have to rebuild the trans soon

@GaryFerraro

7 жыл бұрын

There not bad to work on

was wondering do you have a video for a 2000 Mazda MPV

@GaryFerraro

7 жыл бұрын

Not at this time no, i will keep that in mind, are you having a transmission problem with a Mazda?

Hi fault with my box no reverse and only drives in 3rd no fault codes the dealer replaced the computer (Tcm) I stripped the box as to your video nothing any ideas also do you have a rebuild video so a put parts in correct order thanks nick

Thanks Gary busy as hell up at 330 to make us a video happy Easter my friend

@GaryFerraro

7 жыл бұрын

Yes sir, thats the only time i can film, as soon as that clock hits 8AM the phones dont stop

Olá tudo bem? Parabéns pelo belo trabalho!!! Top.

@GaryFerraro

4 жыл бұрын

Thank you

Gary, great video of the tear down. I just bought a used terrain (2011) w/ 87k miles. 3 days later 3-5-r went out! Thankfully the dealer looks like they are going to take care of the bill for a new transmission! My question is, since the filter isn't serviceable, and I want this vehicle to last a great while, would it be a good idea to add a external filter of some sort? Would it help or think maybe Cause more problems? I'd greatly appreciate any recommendation you have. Thanks!

@GaryFerraro

6 жыл бұрын

I never liked adding those inline filters, had problems with those. Even when i get a job in and it has one i eliminate it. The only thing you can do is drain and fill, do that every 20k miles

Hi I think your a very good mechanic no question about that I'd like to ask you a question I have a Ford f150 2009i want to go to a good school for ford's motors do you know of any? I can pay for the training . Just wannabe able to work on my own stuff. Thanks

@GaryFerraro

3 жыл бұрын

Not sure of any places for training, where are you located?

Hello I have the 6t45 out of the 2014 malibu with 70k miles. While shifting from 2nd gear to 3rd gear there is a jump in rpm. Sometimes a 2000rpm jump other times a 300rpm jump. What would be my best option

@GaryFerraro

4 жыл бұрын

Sounds like the 3rd clutch is going out. How is reverse?

@ronaldbarrios2909

4 жыл бұрын

@@GaryFerraro reverse is fine. Even does it In manual mode. Now it does it worse when going around a sharp turn such as a uturn. Other times it doesnt do it at all

@GaryFerraro

4 жыл бұрын

ronald barrios If it does this around a turn check the fluid level. Do you know how to do this?

@ronaldbarrios2909

4 жыл бұрын

@@GaryFerraro from what I know the 2014 malibu doesnt have a dipstick but it does have a cap where I can add fluid.

@GaryFerraro

4 жыл бұрын

@@ronaldbarrios2909 That is correct, there also is a plug to check to see if it's full of fluid, do you know the location of this plug?

Good

How many miles were on it

@GaryFerraro

5 жыл бұрын

I believe around 80K

Hi Gary, question for you if you don't mind. I got a Chevy Malibu ltz 2008. I started having issues with trans like 6 months ago, it kicks/jerks between 1 to 2 and 2 to 3 gears and had some weird noise in reverse. The trans broke down approx 3 months after that. I took the car to a shop, so we agreed to rebuilt. After 2 weeks in shop, car was "ready", we gave a test drive and trans did not shift gears after two blocks driving. After couple days more in shop, mechanic said I had to replace the valve body with all solenoid on it plus computer. He said I cant replace solenoid separate on this car but the whole valve body including computer and reprogram it. After 10 days he replaced it and reprogrammed it. The car last in good shape like a week and started jerking in 1 to 3 gears and sometimes even slipping gears at higher speed. Mechanic said maybe the valve body was defective and need to get a new one from dealer. Two more weeks, he got a "new" one and reprogram it according. First two days car was ok, after that the car started again with same problems. After two months and $3,000 the car is still with same symptoms as just before it broke down. I am thinking the guy never really replaced the Valve Body for the car still shift hard and jerks between gear 1 to 3 either up speed or down. At this point I am done and I am taking the shop to court to recover the money. But out of curiosity, can a valve body be defective twice, new part from dealer?, can the problem be the programming?, can the solenoids be replace individually?, what are the damage to hard part after all these hard shifting?, where do you think the problem comes from, electrical or mechanical?. Thanks Gary for any help on this.

@GaryFerraro

6 жыл бұрын

Question, would you say the car worked better hot than when its cold or it did it not work regardless? Im not sure what they did, but its possible they are buying aftermarket valvebody/tcm(this part is called TEHCM)(Transmission electronic hydraulic control module). There is a company called doorman that sells this part on the aftermarket and they are nothing but trouble. When all of this started do you know what codes were present?

@davidgutierrez8795

6 жыл бұрын

Morning Gary, thanks for replying. The trans definitely worsen when warm and specially in high traffic. There are no codes for the regular hard shifting but when, it once slipped gears the check engine light came on giving: P0700 and P0752, last one refers to a problem in a solenoid I guess. I pretty sure the guy didn't install a brand new dealer part but instead as you said an aftermarket one, hence all same symptoms. It's been a nightmare the car itself and now the mechanic. Thanks Gary.

@GaryFerraro

6 жыл бұрын

Do you have any other issues with the car? any issues with brake lights coming on or any lights on the dash coming on?

@davidgutierrez8795

6 жыл бұрын

Gary Ferraro, no right now, the rest of the car is ok, but I have had numerous problems since bought it 1.5 years ago: water pump, gaskets, coils, steering wheel noise, shocks, roof motor, doors internal parts and lately I received a letter/recall from local dealer for the brake light issue but my attention has been on the transmission for the last 5-6 months. I mean I bought this car for my wife trusting GM but now we will eventually switch to a Japanese.

@davidgutierrez8795

6 жыл бұрын

Gary, also could you explain to me how difficult is to replace the valve body and can the solenoids be replace individually for this car or have to replace the whole valve body as I was told, but sound really absurd in my opinion. Thank you.

Looks like an expensive repair, thanks for sharing

@GaryFerraro

7 жыл бұрын

Yes, its a bit pricey

Hello, I have a 6T35 gearbox in my Opel Astra K with 1.4 Turbo 150 hp engine. Is this very similar to the 6T40 we see in this video ?

@GaryFerraro

4 жыл бұрын

I would say yes, is the TCM internal to the transmission?

@JRCW892

4 жыл бұрын

@@GaryFerraro Thanks for your answer, I don't really know but here you have some photos of this gearbox : www.proxyparts.com/car-parts-stock/information/engine-code/b14xft/part/gearbox/partid/9069458/ One picture shows a sticker that should help identify the kind of gearbox it is.

hello Gary we have a question we are working on a 6t40 and we have gone thro it and we are have a hot mode problem if you have any thought it would help thank

@GaryFerraro

7 жыл бұрын

What year is the car, any codes? what is the car doing that that trans isnt working correctly? did you do an overhaul?

@arturocastro1341

7 жыл бұрын

Hi Gary, the car is a 2011 Chevy Cruze. No codes, we rebuilt the transmission two weeks ago and it returned with transmissions over heating problems. We already replaced the radiator and we replaced the TCM and in the scanner data it shows HOT MODE/YES. We can't complete the clutch re-calibration because of the HOT MODE. If you know anything we would greatly appreciate your advice.

@GaryFerraro

7 жыл бұрын

What was the indication of the trans overheating, did you actually look at the trans temp. The scanner says it cant complete the relearn? If you let the car sit over nite and with key on engine off does it say hot mode "no" and when you start it it turns to yes/ I had this issue, i have to think, because i forgot what i did to fix it. Tcm is new or used?

@arturocastro1341

7 жыл бұрын

On the scanner it shows hot mode "yes" all the time, the TCM is new also, the temperature on Idle it stays 160 to 190, after we get the car on a high way the temperature it starts to get to 270 after about 15 min that the car has been running The original tcm was doing the same and that's why we decided to change it but nothing changed any information that you might remember that could help would be of great help, Thank you.

@GaryFerraro

7 жыл бұрын

cooler flow is good? rebuilt torque converter installed? did you pull a cooler line off to check cooler flow?

Why was the tcm replaced on this repair?

@GaryFerraro

5 жыл бұрын

These tcm's are problematic every overhaul gets one. A few times i tried to get away with not replacing them and after overhaul the car did not shift correctly so now everyone gets a new tcm and i program it with the latest software

@mikewilson4622

5 жыл бұрын

@@GaryFerraroso you have 50/50 chance of it working. That's not good to hear especially when you consider the price of the TCM and what it takes to replace it if you decide not to replace the first time. Thanks for the all help.

@GaryFerraro

5 жыл бұрын

@@mikewilson4622 Correct, now everyone gets a new TCM and it's been working out very nicely.

@mikewilson4622

5 жыл бұрын

@@GaryFerraro Is there an easy way to get the TCM programmed after the replacement? I don't have access to a pass thru to connect to the car.

Where do you buy your rebuild kits?

@GaryFerraro

4 жыл бұрын

From a company called Transtar

@timpashnik5376

4 жыл бұрын

@@GaryFerraro thank you

@GaryFerraro

4 жыл бұрын

@@timpashnik5376 Welcome

Got the transmission rebuild finished and installed and the TCM programmed (AT LOCAL GM DEALER) with no external leaks, but I have a no movement in any gear? Fluid level is trickling out level plug at running temperature with car sitting level like the service manual specifies. Line pressure is 57 psi in P, 88 psi in R, 57 psi in N , 72 psi in D. The pressures seem low from what I read?

@GaryFerraro

5 жыл бұрын

If this is at an idle, doesn't seem that low, what are they calling for? You did hook up the manual valve?

@mikewilson4622

5 жыл бұрын

@@GaryFerraro the webinar I read calls for 54-60 in Park & N, 100-105 in Rev, 84-87 in Drv & L , as for the manual valve? I think I missed that important step, after you mention it. I guess will look at that tomorrow and see what happens. Thanks for the help.

@GaryFerraro

5 жыл бұрын

Mike Wilson keep me posted

@mikewilson4622

5 жыл бұрын

@@GaryFerraro Got it back together and is shifting but seems kind of rough when going into reverse? Fluid is trickling out of level port when engine/transmission is at running temperature.

@GaryFerraro

5 жыл бұрын

All mounts and axles ok? Was the manual valve out

Real clever little transmission. Should have had synthetic Dexron VI from the onset. But, then again, who knows who's right.

@GaryFerraro

3 жыл бұрын

I actually think it does, i always go synthetic with this trans

I know this is an older video but I just recently bought a 2017 cruze LT automatic and really need this car to get me back and forth to work. I've noticed this transmission is having weird shifting patterns. It seems laggy during shifts, having weird shuttering that feels like misfires(no misfire counters), it hard shifts into 3rd gear sometimes, and after driving about 40 miles, it will start making this roaring sound like a wheel bearing is going out. It was super quiet and smooth today but when I got into town where my job is, it started making this loud roaring sound. I got in it and drove it home after my shift and it sounded quiet and I was driving slow and cautiously and it seemed fine until I pulled into town. I came to a stop at a stop sign (been rolling stop signs to keep the start stop from shutting my car off for 2 seconds), and when I started down the street, it started making this weird roaring(bad wheel bearing noise) and I noticed a smell coming out of the vents, I heard that this trans emits a burning smell when it starts to fail. No engine lights, limp mode, or any codes stored in the pcm as far as I know. I have a 30,000 mile warranty through the dealer I bought the car from, should I be concerned my tranny on my new car is starting to go. Im sure with no codes they wont do anything to rebuild my unit. I also found out they did a 100 point inspection but the guy checked off all of the areas like he was just rushing through it. It has no dipstick, so the only way to check the fluid quality is to drain some out. I read that you need to be vigilant on changing the fluid because the filters are internal and are not serviceable. It has almost 71k on the odometer.

@GaryFerraro

Жыл бұрын

I would go back there when it's making the noise and drive with the service manager. Does the noise change with the engine rpm?

@ATSNorthernMI

Жыл бұрын

@@GaryFerraro This is my second day with it. It did it yesterday after a 40 mile trip, sounds like wheel bearing, output side of trans. Does not change with RPM. It has a shutter like the engine is misfiring(seems to get better the more I drive). Last night pulling into town. I had to do a couple of sharp turns around the corner and I noticed some kind of smell(thought people were burning trash, really faint inside the cabin) and the roaring came back. I came to a stop and then took off again to see if it was doing it during its shifting and it the sound was almost like a differential was starting to howl. I will drive it up there tomorrow on my day off and see whats going on.

30:32 >Finally sees oil filter. >It's in the bell housing(?) on the pump. Welp, so much for changing my filter at home.

@GaryFerraro

4 жыл бұрын

Shining Hero correct. Unit has to be split apart

@rickwest2818

4 жыл бұрын

That's some brilliant engineering right there. Why can't they put the filter on the outside? That, a drain plug, and a proper dipstick and people would actually service these things.

At 30:50/1 above his thumb there is a rubber plug on the bell housing anyone know a part number for that? Thanks

@GaryFerraro

4 жыл бұрын

Is the plug in the bell housing?

@RaulGonzalez024

4 жыл бұрын

Gary Ferraro it is on the exterior of the housing, the upper portion The time stamp that best shows it is 30:50

what the torque spc

I thought u check the fluid level with car running am I wrong?

@GaryFerraro

3 жыл бұрын

you are correct, did i say check with engine off?

So in essence, you can use the damaged drum over.

Can you put a 2ed gen transmission in a car that had the 1st gen transmission

@GaryFerraro

3 жыл бұрын

No, solenoids and valvebody are different

Eek the prices to rebuild - as a shade tree I go to pick&pull and buy for $150 or eBay for $350 w/ a short warranty. Then I might pay $600 to replace. Lucky so far since all worked for years...

@GaryFerraro

5 жыл бұрын

Yes, you are lucky, are these low mileage units?

Gary the black plastic is the termostat to keep the oil on side

@GaryFerraro

3 жыл бұрын

below a certain temp (140F) it allows oil to drain from the side cover as the temp increases it traps the fluid in that area and the fluid level rises

Gary do you have a video if this trans going back together the diagrams on thus one just don't make since

@GaryFerraro

6 жыл бұрын

jimbo251987 Sorry I do not. There is a company in Miami called ATSG. They have a manual on this transmission.

@jimbo251987

6 жыл бұрын

Gary Ferraro yeah don't need it the case is messed up it got so hot that it warped the case. The reverse diode will not go back in

@GaryFerraro

6 жыл бұрын

may not fit all ways, you tried different ways to put the part in?

@jimbo251987

6 жыл бұрын

Gary Ferraro yes sir

astra/opel j .p0776 perssure control solenoid valve 2 stuck.how to fix it

@GaryFerraro

3 жыл бұрын

That is a mechanical code which means an internal problem, what is the transmission doing, slipping?

@GQ1COSDELL

3 жыл бұрын

@@GaryFerraro yes slipping all gears

@GQ1COSDELL

3 жыл бұрын

first gear ok .and no more gears are working

@GaryFerraro

3 жыл бұрын

@@GQ1COSDELL and no reverse?

@GQ1COSDELL

3 жыл бұрын

@@GaryFerraro yes and no reverse

rev out in D and no reverrse what to do

@GaryFerraro

3 жыл бұрын

Would have to come out and be overhauled

Hello, good vide, but i have a one qustion, Where is the oil filter?

@GaryFerraro

5 жыл бұрын

Inside the trans, connector to the pump

@isacolivas926

5 жыл бұрын

@@GaryFerraro thank you Gary i have a problem whit this trans, have a code p0796

@GaryFerraro

5 жыл бұрын

@@isacolivas926 Do you know the definition of that code?

@isacolivas926

5 жыл бұрын

@@GaryFerraro yes, and desarm the transmision and i have the same problem as this trans, thank you!!

@GaryFerraro

5 жыл бұрын

@@isacolivas926 what is the year make model and engine size of your car

Man you know your business

@GaryFerraro

3 жыл бұрын

Thanks Jerry

The ATF coming out of the 6T40 on your work bench looks black. I bought a used 2012 Malibu and did 3 drain and refills at 65,000 miles. I 'm sure it was the original fluid and it was black. What's the original color. All I've ever seen is bright red.

@GaryFerraro

4 жыл бұрын

Dextron 6 is original fluid, i do believe that is red.

@iroc8750

4 жыл бұрын

@@GaryFerraro Yes it is. Would it get black by 65,000 miles?

@GaryFerraro

4 жыл бұрын

@@iroc8750 It got this black because the trans went out, fluid may be discolored but i would say it shouldn't be black like the video

@iroc8750

4 жыл бұрын

@@GaryFerraro Thank you. But after 3 drain and refills last June it shifts fine.

@GaryFerraro

4 жыл бұрын

@@iroc8750 Good deal, keep driving and stay safe

what year is this malibu?

@GaryFerraro

3 жыл бұрын

not sure may have been 2012

@1111comment

3 жыл бұрын

@@GaryFerraro I changed the yellow TCC pressure solenoid on a gen 2 6t40 because the resistance was 4.4 ohms compared to the rest which were around 5.6 ohms. Then, the car would not crank/start in park or neutral, which has me thinking I didn’t seat the transmission range sensor connector properly or that the sensor is bad. Trying to fix a rough idle. Was able to get the cover and valve body out with the car on the floor. Hoping to do this myself. Can the transmission range sensor be changed from the front?

@GaryFerraro

3 жыл бұрын

@@1111comment Do you have a scan tool? does it show live data?

@1111comment

3 жыл бұрын

@@GaryFerraro I put the original solenoid back in today and just reseated the range sensor connection but still getting these errors: U0101: lost communication with tcm, & U2106: CAN data bus, TCM- no communication. Battery voltage has gone down to 12.3. Was thinking the range sensor was causing an open circuit. But, it’s looking like it’s time to take in to a professional. (i have an ancel ad410, and the Car Scanner app that both show live data, nothing fancy)

@GaryFerraro

3 жыл бұрын

@@1111comment range switch will not cause U0101, this happened after you swapped the solenoid or original problem?

Where can I order this rebuild kit for 6T40 ?

@GaryFerraro

2 ай бұрын

where are you located?

@RC_BASSBOY

2 ай бұрын

@@GaryFerraro I'm in California also another question I have a 2011 Chevy Malibu with the 1 gen transmission can I install a gen 2 transmission and have it reprogrammed to the Malibu ?

@RC_BASSBOY

2 ай бұрын

Would like to rebuild my gen 1 transmission

@GaryFerraro

2 ай бұрын

@@RC_BASSBOY No, have to stick with Gen1. What wrong with the trans?

@RC_BASSBOY

2 ай бұрын

@@GaryFerraro Oh really I bought a 2012 Malibu as a parts car for my 2011 so the transmission won't work why is that ? I posted a comment a year ago about what was wrong with it trying to tag you on the comment.