6 Point Harness Install in the FRS
We're finishing up on the inside of the FRS today with a 6 point harness install. We also need to put back some of the interior to clean things up and to abide by the rules set by Gridlife to run ClubTR. The harness is going to hold us in a whole lot better than the stock 3 point so I won't have to worry about bracing myself in the seat while driving.
Racequip 6 Point Harness: www.racequip.com/seatbeltsharn...
Autopower Roll Bar: www.autopowerindustries.com/r...
Recaro Profi
Current Setup
Verus Engineering UCW Rear Wing
Verus Engineering Composite Front Splitter
Verus Engineering Air Dam
FT86SpeedFactory UEL Header
Verus Engineering Hood Louvers
Perrin Oil Cooler
Stoptech C43 Big Brake Kit
Hawk HP+ Pads
Verus Engineering Brake Cooling Kit
Apex EC-7R 17x9 +35mm
Bridgestone Potenza RE-71R 245/40/17
Rays Gram Lights 57CR Ceramic White Pearl 17x9 +38
Falken Azenis FK510 245/40/17
Remark R1 Spec Titanium Catback Exhaust
Tomei Front Pipe
Motiv Overpipe
Recaro Profi SPG
Buddy Club Super Low Down Seat Rails
Helix Depo K Shade Tail Lights
17+ Instrument Cluster w/ Digital Display
Gerald Just Projects Cluster Retrofit Kit: tinyurl.com/2p8d6uva
Instagram: / v
Пікірлер: 31
Best tutorial how to install harness and mounting points so far, nice!
@KevinVo
Жыл бұрын
Glad you found it helpful!!
Definitely best tutorial for harness mounting points!!!
Very clean job man. Super super clean.
@KevinVo
2 жыл бұрын
Appreciate the kind words Peter!!
Solid video, thank you!
You make me wanna do a setup like this on my frs on of these days for the track 😮💨
@KevinVo
2 жыл бұрын
Do it!!!!! Can't really drive the car on the street now though haha
Awesome video dude
@KevinVo
2 жыл бұрын
Thanks dude!! You're next!
what was the thread pitch for the eye bolt that u threaded into for the stock 3 point seatbelt location
I’m doing the same install, just curious as to if it is necessary to anchor the shoulder harness after wrapping it around harness bar?
@KevinVo
Жыл бұрын
Wrapping it around the harness bar is the anchor.
Great video kid! 🤣. How long do you think this would take, start to finish, if a normal person had to do this?
@KevinVo
2 жыл бұрын
Thank you thank you! 😅 I am a normal person what are you talking about?! haha if I didn't have to film the project and didn't have to wait for the powder coating on the roll bar I could've gotten this done in a weekend as long as my welder was available.
@shinigami052
2 жыл бұрын
@@KevinVo No you're a super hero! But actually I was thinking without having to film and stuff.
Heyo! Question, did you use a locking collar to keep the harness from sliding? If so which one?
@KevinVo
2 жыл бұрын
Yes, I used some ASR collars.
Track days coming up! When are you going to swap in that FA24 engine?
@KevinVo
2 жыл бұрын
haha maybe in a few years 😅
Did you need to plug a resistor for the Yellow Airbag Connector that the factory 3 point plugs into?
@KevinVo
2 жыл бұрын
Yes I did
@NooGai808
2 жыл бұрын
@@KevinVo which ones?
Am I the only one wondering how that big washer and nut went into that small hole in the frame rail?
@KevinVo
Жыл бұрын
There was a slot just big enough for me to slide the washer through.
Is this the same method in installing the 5 point harness as well? Thanks
@KevinVo
Жыл бұрын
Yes same process!
@dmw_99
Жыл бұрын
@@KevinVowouldn’t the fuel lines get in the way?
@KevinVo
Жыл бұрын
@@dmw_99 I was able to sneak in between them.
7:08 *sighs* “THAT IS TIGHT!!! Oh I really gotta be careful not to pinch my wiener in there”