5 Things an RC Motor Manufacture Doesn't Want YOU to Know
Ғылым және технология
Here are a severals facts that most RC Brushless motor manufactures will not want you to know.
👍 Want to know the Next Video Topic? Consider supporting the channel for awesome Perks: 👍
Patreon Page: / rcexplained
🛍️ Ordering from Amazon? Use this Affiliate Link to support the channel: 🛍️
amzn.to/2QTNjHL
A few videos:
What Kills a Brushless motor, current or voltage?
• What kills an RC Brush...
Should you Select a High Voltage or High Current Setup?
• Select an RC High Volt...
Does Increasing the Motor Kv value Increase an RC Cars Top Speed?
• Does Increasing the Mo...
#RCexplained
Пікірлер: 43
Join the Group Chat before and during the Premiere of the Video! Let me know if we should do a Premiere style video again where I will be live before and during the video in the chat. It was great chatting with the people that joined!
@rcnitroflux2361
3 жыл бұрын
Will do bud
Wow. Fantastic info
@RCexplained
3 жыл бұрын
Glad you think so!
Thanks for the vid Ryan. I suppose we don't know how much redundancy is built in to a motor. It's a bit like chip-tuning your car: You might get away with a 5 - 10% increase in power output (for example) without sacrificing much in terms of reliability, but anything more could be a risk. Well, at least an RC motor is a lot cheaper than a car, so a little risk-taking is ok I guess!
@RCexplained
3 жыл бұрын
Luckily for our motors, we will know when we hit the limit when the motor is over temp. Unfortunately for full size cars, you won't know you are at the limit until a rod comes out the side of the block.
Thanks for the info. So as long as I don't exceed the max rpm or overheat the motor I can give it the voltage needed to get my desired wheel speed? Still trying to decide what motor to try in my Bomber next.
@RCexplained
3 жыл бұрын
That is correct. The hobbyist also assumes all risk when exceeding a manufactures max voltage limit.
My morning starts with some good video ;)
@RCexplained
3 жыл бұрын
That is awesome!
Thanks for explaining ryan, this helps me tremendously with rpm value and the voltage of a lipo battery pack to use safely within that range
@RCexplained
3 жыл бұрын
Great to hear!
I guess if you have a large enough rc, you might be able to figure out how to mount a pc radiator, pump and water jacket to keep the motor cool.
Another good video - I've been binge watching your series like Netflix lately! Question: sometimes manufacturers quote maximum efficiency specs for motors. Do you ever take this into account when selecting a motor?
@RCexplained
3 жыл бұрын
I usually do not as not all manufactures provide that specification. If they do, it doesn't mean that the configuration planned to be used will be able to hit it.
So if I have crazy game changer fans for my motor that literally run on a 3s 2500 mah lipo and wake neighborhood up can I gear to the moon?
Thanks for the vid
@RCexplained
3 жыл бұрын
Thanks for watching Eric, and nice chatting with you!
Anybody try wrapping copper heat pipes around an rc motor for cooling?
Nice videos man u have me in a much needed class I'm new to rcing hobby thankyou u think u can put a build
@RCexplained
3 жыл бұрын
Thanks for the comment. I'd like to do a video with a build.
Dense info much satisfaction. Thank you sir!
@RCexplained
3 жыл бұрын
My pleasure
Very helpful!👌👌👌
@RCexplained
3 жыл бұрын
Glad you think so!
Great vid bud
@RCexplained
3 жыл бұрын
Thanks!
Is there a reason that you rarely see people use thermal paste with heatsinks and motors? I can't think of any but one assumes that would greatly improve the cooling performance.
@toolbaggers
3 жыл бұрын
Rc car people need to talk to PC people. PC people know that a large heatsink must be in as close contact as possible with the cpu for efficient cooling. Most rc car heatsinks have huge gaps with very little contact between the motor and heatsink with no thermal compound and with teeny tiny over revving fans.
@RCexplained
3 жыл бұрын
It would definitely help thermal transfer. I wouldn't want to use thermal past on the motor just because it tends to be quite messy. But if I wanted to win a race or gain an edge, I wouldn't think twice. ;)
@toolbaggers
3 жыл бұрын
Then you pc builders that have 20 different wires for 12 volts on multiple connectors when they should just use larger gauge wires.
@frasersteen
3 жыл бұрын
@@toolbaggers this was entirely my logic. My buggy's heatsink slides all over the place, definitely not good for heat transfer. It's running pretty cool so no point but if I run into heat issues that's the first thing I'm trying. My bet that will do way more than sticking a bunch of extra fans on.
@toolbaggers
3 жыл бұрын
@@RCexplained thermal compound makes a HUGE difference in the world of PC cooling. But unlike in rc, it's very very easy to conduct repeatable, and well defined testing methods that PC gamers do when overclocking their rigs.
Your videos are so important Me and my mate ran a 6s blx arrma motor on 8s and it was good for a few months which was enough , Do you get email on data log , Waiting for xlx2 Thanks for another interesting video
@RCexplained
3 жыл бұрын
Thanks Cmw. I did not receive an email about a data log.
Extra Tom in that sweater
TMI ugh I’m more confused as to what motor I need
@toolbaggers
3 жыл бұрын
RTR is for you.
Oh, Teton gain :)
@RCexplained
3 жыл бұрын
The Teton fits on the desk quite easily!
Absolutely nothing wrong running a 32pitch with a 0.8pitch gear. If the mesh is lined up right, the difference in pitch isn't even noticeable even running the car over time. Never cross a pitch like 32p with 0.6p or 48p but 32p with 0.8p is fine.