5 Guaranteed Tricks to Remove Stuck Screws

Тәжірибелік нұсқаулар және стиль

In this video I'll show you 5 tricks to remove almost any stubborn or stripped screw. I work around old building so I encounter a TON of old stripped or stubborn screws and using one or a combination of these I've been able to remove just about every screw I've needed to.
-----------TOOLS & SUPPLIES-----------
WD40 Rust Release Penetrant - amzn.to/3o3rh7m
Ryobi Screw Extractor - amzn.to/3kDAIZe
-----------LINKS-----------
Instagram - / thecraftsmanblog
Patreon - / thecraftsmanblog
Facebook - / craftsmanblog
Website - thecraftsmanblog.com
Store - thecraftsmanstore.com

Пікірлер: 111

  • @every1readthis
    @every1readthis Жыл бұрын

    I just came here to comment. I had a nightmare situation with a shower drain cover screw. One of two came off nicely the other was rusted out and stripped. It tested me and about 10 different tools, along with WD-40 the smell and headache lol. I was just about to give up and accept the loss, but one KZread search first video this one and the tapping with a hammer ever so slightly with a flat head on what was originally a Philips, this was the solution to the problem. Thank you sincerely The Craftsman Blog. It works folks, hit the like button so others can benefit as well with algorithms. 😅

  • @DianeAloia
    @DianeAloia21 күн бұрын

    Thank you! Using Steps 2 and 3 allowed this little 68 year old woman to take terribly rusted screws out of the bottom of my old Rubbermaid shed so I could take the floor apart.

  • @imclcinforzahorizon8951

    @imclcinforzahorizon8951

    21 күн бұрын

    Way to go old Lady, Nicely Done 🤝👏👏👏👍✌️❤️

  • @samanthal2926
    @samanthal2926Ай бұрын

    Tapping the screwdriver with a hammer worked for my crusted (calcium build up) shower drain screws! Thank you for saving me even more frustration!

  • @chrislrob
    @chrislrob8 ай бұрын

    Thanks for this! Earlier today I was in my basement cursing a blue streak at a single screw lodged in a 100-year-old beam that was ruining my life! And it was in a tight spot. You inspired me to give my screwdriver a few whacks and I was able to get it out. Great vid!

  • @lindafelipe9062
    @lindafelipe9062 Жыл бұрын

    You saved our butts, we had an old bed frame and we had a tough screw and your tips were perfect, Thank-you

  • @rebecapotasnik9012
    @rebecapotasnik9012 Жыл бұрын

    I was ready for the nuclear option, having tried everything else (except the screw extractor tool). My situation is a little tricky as the stuck screw is in the sash lock so very close to the pane of glass. My friend suggested I try one more thing before drilling out the screw-gentle prying of the sash lock to provide another way to loosen the screw. It worked! I was finally able to unscrew it.

  • @stephanieblock6087
    @stephanieblock60877 ай бұрын

    Aghhh yes thank you! Super old flat head screws in very old kitchen cabinets and I couldn’t get them out to save my life. Google sent me to you… I took off all the paint, that didn’t work alone, so I sprayed with WD-40 and that alone didn’t work, I also tried tapping the flat head screw driver in before I added the WD-40 and that didn’t work alone. But after I added the WD-40 and tapped the screw driver, wala it worked! I am so happy!! Thank you for your time and sharing your knowledge

  • @kiransri1515
    @kiransri1515 Жыл бұрын

    Thanks a lot. Worked very well. Appreciate your help for novice like me

  • @thelmasbar
    @thelmasbar Жыл бұрын

    I had to use my Dremel to clear the groove on the screw top! Idk what kind of concrete-type paint had filled it in but it wouldn't budge before I dremel'ed it out!

  • @peppermintpatty14
    @peppermintpatty142 жыл бұрын

    THANK YOU TIMES A MILLION! I worked on these a couple hours a night and FINALLY got six screws removed with your hammer pounding/screwdriver method. 👍🏼👍🏼👍🏼👍🏼

  • @NaketaTV
    @NaketaTV Жыл бұрын

    Your video saved the day!!! Thank you so much.

  • @andystone8917
    @andystone8917 Жыл бұрын

    Thanks mate, I didn't think I was going to get my old gate latch off but you made it possible!

  • @halcyon2017
    @halcyon20172 жыл бұрын

    Thank you so much for these tips! Using the hammer and screwdriver worked beautifully!

  • @bxlawless100
    @bxlawless10011 ай бұрын

    I’m impressed. The hammer trick worked fantastic.

  • @EgressFromStress
    @EgressFromStress24 күн бұрын

    Bro, if it wasn’t for you I would have got my corroded Screw for my pool pump loose. Thank you soooo much for this video!!

  • @Ashley-id2cb
    @Ashley-id2cb11 ай бұрын

    You just helped me not loose my mind! Got my screw out successfully with the hammer trick! Thank you!

  • @LindsAyWithAttitude
    @LindsAyWithAttitude Жыл бұрын

    Thanks for actually using good music. I feel like that made this video so much better. 😊

  • @user-rp8qe4ui4o
    @user-rp8qe4ui4o9 ай бұрын

    Thank you, thank you! The WD40+hammer approaches worked to loosen screws in some storm windows that I thought were glued in permanently.

  • @peppermintpatty14
    @peppermintpatty142 жыл бұрын

    THANK YOU TIMES A MILLION! It took me a couple hours for two nights to get six screws removed with your hammer/screwdriver method. Much appreciated!! 👍🏼👍🏼👍🏼

  • @TheCraftsmanBlog

    @TheCraftsmanBlog

    2 жыл бұрын

    Awesome!

  • @tokkihere
    @tokkihere Жыл бұрын

    OMG you saved my life thank you so much!! I had been trying to get a tight screw out something I assembled a few months ago but wanted to remove a part of it and there was one screw that just DID NOT want to come out!! I was about to lose my mind, id even tried to get it out with a drill even though I had hand tightened it when assembling it and it STILL was not budging!! Finally then I watched your video and when back to the hand method before and tapped it with a hammer while turning it and it INSTANTLY loosened up. I don't think I've ever been so mad and so relieved at the same time haha 😂

  • @72PSI
    @72PSI18 күн бұрын

    Thank you for sharing.

  • @timtim4603
    @timtim46039 ай бұрын

    Yes brilliant, solved a problem of rusted screws in outside electrical box, thank you soo much

  • @nieceypiecey100
    @nieceypiecey1005 ай бұрын

    This video was a lifesaver! I was ready to pull my hair out! ❤

  • @susanamundson6390
    @susanamundson6390 Жыл бұрын

    This worked!! I had to go to tapping with the hammer while turning the screw. Voilla! Thank you, thank you, thank you.

  • @anthonycantu8879
    @anthonycantu8879 Жыл бұрын

    Tried the wd40 approach, first, and that prompted me look for another method. That led me here. I didn't want to tap/pound on my screwdriver while turning it, so I took a more direct course. I tapped on the screwhead itself. Between the spray and the tapping, I easily removed the screws. Thanks. 👍

  • @exchequerguy4037
    @exchequerguy40376 ай бұрын

    Thanks :) I got my sundeck screw out by removing the top plank, hammering small holes around it, and using locking pliers, at the tightest grip possible, around the screwhead.

  • @cozdinho911
    @cozdinho9115 ай бұрын

    Thank you, I’m a college student renting and I had to replace the door stopper on the front door, 2 screws on the old bracket just won’t give so i’ll give these a shot! First thought was wd-40 but i’ll give the hammer a go as well!!

  • @sadierockins9290
    @sadierockins92902 жыл бұрын

    Bless you for that simple hammer trick.

  • @abutterfly7975
    @abutterfly7975 Жыл бұрын

    Tried everything nothing worked, but then I tried the lubricant hammering the screwdriver and turning it as I went, and it finally got those stripped screws out. Hallelujah thank you good man.

  • @user-ik4mf2je9l
    @user-ik4mf2je9l6 ай бұрын

    huge! so helpful!

  • @ShadowzGSD
    @ShadowzGSD2 жыл бұрын

    also try tightening the screw a bit to break the bond and then undo (save killing the head when undoing) and step 6 - world war 3 option is burn the wood and remove screw from ashes (screw removed in one piece)

  • @I3HrN
    @I3HrNАй бұрын

    Thank you so much! ❤

  • @orellinvvardengra6775
    @orellinvvardengra67759 ай бұрын

    Probably gonna have to use the hammer tapping trick on this old craftsman router table my friend gave me. According to him it's been sitting in a bucket full of water and it looks like it. The screws attaching the router to the table are incredibly rusty and I've had a penetrating oil sitting on them for a couple days now. I just really don't want to strip these things out, it would be an amazing tool if it was up and running; the thing is older than I am.

  • @aquarianhealer
    @aquarianhealer10 ай бұрын

    Had 4 badly rusted screw heads that just crumbled when I tried to unscrew them. I soaked each one with WD-40 and used a drill on 1st one which was an epic fail. Used hammer and philips head screwdriver and other 3 came out with ease. Thank you.

  • @blabbergasted4380
    @blabbergasted43802 ай бұрын

    Nice. Thanks!

  • @rvatto7144
    @rvatto71442 жыл бұрын

    Screw extractor worked for me. The trick is use a small drill bit to drill in pilot hole the just the extractor on a rahet and unscrew slowly

  • @peterbarlow8912
    @peterbarlow89127 ай бұрын

    Use a regular screwdriver. I have found hitting a six in one driver damages them. One the handle split in half! Another one the the insert became permanently jammed. Use the corner of your straight blade and hit the side of the point. I’ve had to remove many heavily painted wooden storm window hooks off casings.

  • @underscorewill
    @underscorewill Жыл бұрын

    very good

  • @leeb.7188
    @leeb.71887 ай бұрын

    I purchased a rental unit, which has about 50 years of “deferred maintenance” (i.e., it’s a dump). Someone had placed exterior weatherstripping, with a metal band and heavy rubber insulation, all around the bedroom door. And then painted over it with five different colors over the years, lol. It was attached with 25 small screws, with an odd bit head that I’ve never seen before. I couldn’t get them to budge. After watching this video, I tried pounding them with a hammer and heavy duty Phillip’s head screwdriver. That got 20 of them out. (Note that I first used a ratcheting screwdriver that I put a bit in, and that didn’t work, so I switched to a solid shank screwdriver.) The remaining five screws had been over-tightened and driven so far into the metal that the hammer method didn’t work. I purchased a damaged screw removal kit from Amazon, as well as Engineer brand screw extractor pliers, model PZ-58 for $18. These pliers are made in Japan and are expressly made to grip stuck screws. They come in different sizes but this model works for average size screws. Anyway, due to the unique design, I was able to remove the remaining screws. Note that the Vampire brand is made by the same company, but they’re red, have a cute name, and are marketed to Americans. They also cost more. The Engineer brand come in a package with Japanese writing and are plain forest green. But the function is the same. I’m just passing this along for anyone who is at wit’s end with stuck, damaged screws. I’m glad I didn’t open the screw extraction kit and am returning it for a refund. Between the hammer method and the Japanese pliers, I got all of the screws out this evening in about an hour.

  • @stanmerrill3090
    @stanmerrill30907 ай бұрын

    The hammer trick really worked!

  • @CrowdPleeza
    @CrowdPleeza3 ай бұрын

    How exactly does the last option work? Do you just drill into the screw until it breaks up? My stripped screw is inside the hole of my bathtub turn knob.

  • @brucemartini2288
    @brucemartini22882 жыл бұрын

    Doing deck rebuild- found rubbing alcohol lubricates the wood for screw removal

  • @nestor8369
    @nestor83692 жыл бұрын

    Much easier way to remove paint off old screws is a thumbtack just gotta look for the line on the screw then cut the paint off after that you can use your flat head screwdriver to remove the screws instead of destroying them.....

  • @Dennis_Parkes

    @Dennis_Parkes

    Жыл бұрын

    I remove paint on and around screwhead with a dab of paintstripper. Has worked everytime for me so far.

  • @thelmasbar

    @thelmasbar

    Жыл бұрын

    sometimes you just have to say goodbye to a few old screws.

  • @TDuD3
    @TDuD33 ай бұрын

    If I want to apply new screws into the same holes with rust in them, is a good idea an this will not affect the new screws ore is there a step to do before installing the new screws?

  • @joshbrekke6374
    @joshbrekke63742 жыл бұрын

    Try seized in 3” square drive deck screws through Trex decking where the pilot hole through the trex was 1/64” then the almost 1/4” diameter deck screws were powered/forced home. 350 of them so far and about another 750 to go, argggg! They have been in there since 2008

  • @STEINYY
    @STEINYY9 ай бұрын

    What if it’s in a really bad area where there aint enough room to work. My situation is the front grill of a car where I can’t get in and remove this old as screw:/

  • @Joe-nd6rf
    @Joe-nd6rf5 ай бұрын

    Thanks, you Save me a bunch with a nuclear method. Thank you very much.

  • @CrowdPleeza

    @CrowdPleeza

    3 ай бұрын

    Did you try that last option for drilling out the screw? How did you do it? Do you just drill into the screw until it breaks up?

  • @Kur4zy
    @Kur4zy2 ай бұрын

    Thanks

  • @tombusshart3971
    @tombusshart3971 Жыл бұрын

    I wonder if a screw extractor would work if it was used on a screw gun ( because of the impacting )

  • @karryjohnson3261
    @karryjohnson32615 ай бұрын

    I have a screw that is stuck in wood plastic. I was trying to fix a hole that I needed to drill and put the screw in thinking that it cured. Any tip or recommendations on tools to use to remove the screw?

  • @yiliao123
    @yiliao1232 жыл бұрын

    I tried to replace strike plate from a wood door frame. But I have trouble to remove the stuck screws. I tried WD-40 and hammer. None of them worked for me so far.

  • @confloashton3617
    @confloashton36178 ай бұрын

    I've got a screw that is designed to be turned by hand, having ridges around the edges of the head. And that is stuck, do you have a suggestion for that?

  • @cynthiacope6815
    @cynthiacope68155 күн бұрын

    Hello, Im trying to fix my leaky kitchen faucet. My allen wrench fits perfectly but i can't turn the screw, it stuck. Help, I i appreciate your assistance. Im determined to do this myself. Thank you.

  • @AprilYChang
    @AprilYChang9 ай бұрын

    Screw extractors didn't work for us either, our case is that the broken screw head is pointy, couldn't even make a dent with the drill for the step 2 per the extractor's instruction. So, we have been considering the "drill it out" method though not sure if it might work. Stumbling across your youtube here, now I'm more confident to try your #5 (drill it out) idea. I hope it will work for us as well :) Thanks for sharing!

  • @CrowdPleeza

    @CrowdPleeza

    3 ай бұрын

    Did you try that last option for drilling out the screw? How did you do it? Do you just drill into the screw until it breaks up?

  • @drewgrows7765
    @drewgrows7765 Жыл бұрын

    You saved me. The WD40 worked on all but one. I hit the screwdriver with a hammer and got it.

  • @mackvaclaw7048
    @mackvaclaw7048 Жыл бұрын

    I tried to use a screw extractor after trying everything else and it still didn’t work so I just gave up. After using the drill extractor, you take away your only hope left when you destroy the top of the screw, so definitely try it last

  • @WhoaMoments
    @WhoaMoments Жыл бұрын

    Whoa!

  • @hiddenhope7569
    @hiddenhope7569 Жыл бұрын

    Nice jab, mike tyson would be proud 👏 😁

  • @jonskitch8082
    @jonskitch8082 Жыл бұрын

    Screw extraction pliers?

  • @jesalyncarnley5434
    @jesalyncarnley5434 Жыл бұрын

    How do you remove the rest of the screw after drilling off the head? I'm about to drill this one off since literally everything else hasn't worked but I need to put a screw back in the exact same spot and won't be able to if the screw is still in the hole.

  • @nathanproductions5817
    @nathanproductions58174 ай бұрын

    Thank you for trick 2 I had to loose a screw on my vacuum because it was broken

  • @68868s
    @68868s Жыл бұрын

    The screw is soooo shallow and hard to get at. What do you do then?

  • @WexWorld
    @WexWorldАй бұрын

    Are you using reverse in No 5? The nuclear option

  • @NYMArts
    @NYMArts11 ай бұрын

    I can cut glass and deglaze and reglaze old windows....seems Very Familiar to me :o)

  • @joe112000
    @joe11200011 ай бұрын

    Dig the shirt 👕

  • @marque235
    @marque2352 жыл бұрын

    Any suggestions on removing stuck plastic shelf pegs in cabinets when there’s nothing to grasp in order to pull it out?

  • @virgforsberg2754

    @virgforsberg2754

    2 жыл бұрын

    DrI’ll small hole, coat screw aprox same size as hole with super glue and extract

  • @jerriegall

    @jerriegall

    3 күн бұрын

    I screwed a tiny screw inside mine then used a screwdriver and both came out.

  • @cricketinwilton
    @cricketinwiltonАй бұрын

    The two heavy-duty screws are deep into drywall and aren't budging. I tried all your solutions but none worked....I'll keep searching for a way. I may try a bolt cutter.

  • @komoru
    @komoru Жыл бұрын

    The lubricant trick works great....if your screw is not upside down!

  • @michaeltyers7336
    @michaeltyers7336 Жыл бұрын

    Screw extractors are really only useful when the head of the screw has been stripped. But even then they're pretty useless because you're likely to sheer the head off. Ask me how I know.

  • @victoriaviars3554
    @victoriaviars3554 Жыл бұрын

    How can I remove deep in beaded screws. They are deep inside fan.😢

  • @jpnelson7606
    @jpnelson7606 Жыл бұрын

    OK, I was totally screwed (pun intended)... I had a barbecue that needed overhauling, and one damn screw was about to cost me a TON of money in replacing the entire internal guts. Your tricks got the screw loose and I was able to swap out a $40 part instead of a $200 assembly. Do I owe you $160? Sort of feels like it.

  • @yokosh1802
    @yokosh18022 жыл бұрын

    i got problem to remove screw from my car head lamp...its totally stuck, perhaps because of the heat, already tried to give heater but failed...anyone knows how to deal screw stuck because of the heat?

  • @alijaveed9350
    @alijaveed935010 ай бұрын

    screw tap worked!! screws in a child safety screen. more than a decade old!

  • @BrigitteGeorge-gk4qx
    @BrigitteGeorge-gk4qx9 ай бұрын

    I can’t get the handle off a casserole pot lid that is loose to clean and replace.

  • @franksuhuang6
    @franksuhuang6 Жыл бұрын

    👍👍🌹🌹

  • @BigLousWorkshop
    @BigLousWorkshop2 жыл бұрын

    4 Great tips… lol… but not for nothing i’ve had success using a screw extractor if the head of a screw is stripped out but the threads are still moving … if it’s stuck like the ones in your video then yeah an extractor is useless!!

  • @PrisonMike-
    @PrisonMike- Жыл бұрын

    Go Cowboys!

  • @WhattAreYouSaying
    @WhattAreYouSaying Жыл бұрын

    Doesn't work for me. I have an antique rifle from World war 1 with a screw that's really stuck hard. It has also rusted badly. I have tried almost everything in this video and a lot off other different methods and nothing works..Since the rifle is an antique and therefore has a value, drilling out the screw is not an option. It's a screw with a flat head. I need to remove that screw to take the rifle apart and clean it properly. But I have tried for several days now, I think I just give up.

  • @mamadonna3959
    @mamadonna395911 ай бұрын

    What about when the head is broken off

  • @jackatzmon4894
    @jackatzmon48944 ай бұрын

    ummm. I used a screw extractor and it actually worked. My application was a bolt with the head sheered off.

  • @bobbrock41
    @bobbrock41 Жыл бұрын

    The lube trick won't work if the screw is driven in horizontally (eg through a metal plate on a very large gate for a driveway). In fact I don't think any of the above tips work in that situation.

  • @tracyknox8703
    @tracyknox87032 ай бұрын

    The window is NOT a sash. Sashes fit into a frame with parting stops . This hinged window is called a flanker.

  • @tryingcake101
    @tryingcake101 Жыл бұрын

    Nothing is working. I'm at my wits end. I have to remove a shower handle. I even went out and bought the extractor (GrabIt). I may as well have been spitting in the wind. What do you do when nothing is working? I don't want to damage the pipes the handle is attached to.

  • @user-ly6zr7en4x

    @user-ly6zr7en4x

    10 ай бұрын

    Same exact issue. Did you find a solution since you posted this? If so please share

  • @gamesdeen3768
    @gamesdeen37682 ай бұрын

    Yeah....I guess we're going with the drill. The laptop repair tech threaded the screw in wrong and that shit is STUCK. I gotta get the case open to swap out a part.

  • @cadenweichold4400
    @cadenweichold440010 ай бұрын

    Now let’s just hope this works on a fuel pump lol, I’ll keep y’all updated

  • @rebeccacisco9420
    @rebeccacisco9420Ай бұрын

    What if it is in the back of a garbage disposal in a very tight area to work in and the person put it in likely with a drill bit before installing. I need to replace the drain pipe. I am a girl without all the strength of mens' hands. The drill won't fit in the area I am working in. Pulling my hair out over it.

  • @lico2076
    @lico2076 Жыл бұрын

    agree 100 percent about the screw extractors, they shit.

  • @mike_98058
    @mike_98058 Жыл бұрын

    Ha! Here's a real challenge: My wood deck is 30 years old,screws hold the boards down. Now some boards need to be replaced, but the screws are badly rusted (perhaps due to the wood treatment). The top of the screw breaks at about 1/2" into the plank. The portion of the screw remaining in the wood still holds down the planks. Removal of screw is extremely difficult. Once removed, I still have 1" of screw sticking out of the substructure which needs to be cut flush so that the replacment board will sit flat.

  • @angelaocasio

    @angelaocasio

    Жыл бұрын

    Same thing here! Did you ever figure out what to do? I’m at my wits end with this project. I’ve literally tried everything and Nothing works. Plus I have other screws going into boards that I have no idea where they came from. I can only see the end of them. So frustrated with this house.

  • @jerriegall

    @jerriegall

    3 күн бұрын

    Same predicament

  • @paulk5706
    @paulk5706 Жыл бұрын

    Dude... if you'd just use a screw extractor like it should be used rather than with pliers it actually works.

  • @DrJoonPark
    @DrJoonPark11 ай бұрын

    What's your address? I need to send my self addressed stamped envelope to get my check.

  • @ghengis430
    @ghengis430 Жыл бұрын

    Every screw in my house must be the cheapest load of rubbish. Hopefully I'll get the one out I've tried to wrench out with pliers. Anyone got any ideas what I should do? Wish I'd seen this first! 😭

  • @ghengis430

    @ghengis430

    Жыл бұрын

    I got it out!!🥳

  • @kristamorisen2669
    @kristamorisen26693 ай бұрын

    None of these worked? Now what?

  • @jamietingey7498

    @jamietingey7498

    Ай бұрын

    You're screwed 😂 Sorry, couldn't help myself. Good luck.

  • @chriscornelius2518
    @chriscornelius25187 ай бұрын

    None of this works for real problems like the soft screws.

  • @SuperMagoo2011
    @SuperMagoo2011 Жыл бұрын

    Only 4 tricks🙄

  • @StormyMonday0896
    @StormyMonday0896 Жыл бұрын

    nope, didn't work

  • @andrewr7001
    @andrewr7001 Жыл бұрын

    Cut to the chase... The video is literally 25% filler.

  • @kamiahfrey4202
    @kamiahfrey4202Ай бұрын

    This is just common sense. Thanks for nothing

Келесі