in my early model 4L80E build I was not able to use the Sonnax forward drum hub roller bearing. It was too thick, and took away all my input shaft end play. The Sonnax web site does say machining may be required to use that. I just replaced the stock plastic washer those hubs use with a copper washer that came in my rebuild kit.

Good find! Everything else looked minty

Gotta make you feel good that you built it and it stood up to 8 second Volvo power. Those pieces and parts looked great. Quality parts and careful assembly yo!

@scotttimpany2845

Жыл бұрын

Come to think of it... makes ME feel good that the transmission looks great. I followed your vids closely when I rebuilt mine.

@emccolly

Жыл бұрын

I reckon it's GM powered, not Volvo.

Great video

@BlaserBuilds

Жыл бұрын

Thanks!

The lord’s work!

@BlaserBuilds

Жыл бұрын

Holleyluya...

Very good content!!

@BlaserBuilds

Жыл бұрын

Thanks!

The stock 4l80e intermediate piston retaining plate is known to flex and bow with elevated line pressure. I use a thicker th400 retaining plate with the 4l80e springs to fix that problem.

I have a ea valve body in my 80e a buddy of mine had specd from Lonnie. Has lockup in 1-4 and he’s done a few like that actually. But only time they have been used like that is in a diesel application and I talked with him about it over the phone and he seemed to think that the lower rpm of the diesel is what keeps the pump alive with lockup in every gear. Who knows tho

Jake sells th400 style intermediate piston return spring plates. We use them in all 4L80e builds, they don't dish outward like the stock 80e ones do. Then we pull 6 springs off the stock retaining plate and put them in outer holes in the 3 separate locations. Looks like a pretty decent build and nothing really got hurt. Also, that chamfer on the rev band seems normal if my memory serves me right

@BlaserBuilds

Жыл бұрын

Yeah, the new band that went in was the same way. But not sire where the black gritty stuff was coming from. I guess we'll see how it goes, lol. I'll check out the th400 plates for the next one.

@christophersanders5007

Жыл бұрын

I added that same plate from Jakes in my 4l80e rebuild.

Hell yeahhhh boiiii

I thought about buying you some torque sockets

👍

👍💪

Why did you run wave plates? I toss all those in performance builds. I also put the forward hub in, then the clutches. Easier than having to wiggle it in. ;)

@BlaserBuilds

Жыл бұрын

Forward, just maintaining a stock clearance stack and the drum is applied all the time in forward gears so I don't feel like there really much to gain by removing it, unless clearancing for another clutch, and it doesnt apply/release under power. I kept the intermediate just to soften the impact on the intermediate sprag on the 1-2, also stock clearance stack. Direct I removed it to clearance the drum for 6 clutches, and it applies under power.

Hi did you leave the center seal out for dual feed modification on the Forward drum? Thanks

@BlaserBuilds

16 күн бұрын

No, but you can. It's just not part of dual feed. The forward drum seal has a bleed hole and applied the whole drum anyways. Just slows fluid to prevent harsh shift.

I have to build my 4l80, what would you say this trans build is capable of handling? thanks for the videos!

@BlaserBuilds

Жыл бұрын

Should be able to do 1000hp pretty reliably.

What do you think caused the rubbing/beveling on the reverse band.

@BlaserBuilds

Жыл бұрын

Not sure TBH... theres really not anything there to rub it like that.

So what's the fix so it doesn't munch the new pump is he changing the converter or changing the lock up or both I'm intrigued transmissions are not my playpen and are an expensive learning curve if you fudge it

@BlaserBuilds

Жыл бұрын

Not going to do the 3rd lockup.

I have a question Have you noticed anything with filter starvation using the stock pan when launching

@BlaserBuilds

Жыл бұрын

I have not. But I'm also not measuring for it to see if there's a drop in pressure or anything.

@edwinrosadojr4592

Жыл бұрын

@@BlaserBuilds just something I see floating around on the forums about that being a possibility. But I haven’t heard anything from you, Matt or even Cameron mention anything about it

Hello,Ryan! Can you give an advice where to find the problem: I can hear mechanical sound(like pleantary sound) in the end of 1st gear until it shifts to 2nd.starts from 1500rpm if moving slowly, more gas - lesser sound. 1.I have changed 2 oil pumps(no any damage was noticed) and filters with seals. 2. 3 times i've changed overdrive planetary(now billet inside) with new roller sprag spring retainer and snap ring 3. Converter(triple disc with lock up) was also checked and balanced - no damage was found 4. Flexplate to TC also checked 5. all bearings, washers,bushings&seals are changed. 6.Diff also checked Where else i can check to find the problem?

@BlaserBuilds

Жыл бұрын

Hmm that's a tough one.

@alexsoteynykov3492

Жыл бұрын

@@BlaserBuilds can it be caused by too low or high line pressure? Ihave sonnax hd2 booster kit

@BlaserBuilds

Жыл бұрын

@@alexsoteynykov3492 Is it a whining sound? Or metal on metal?

@alexsoteynykov3492

Жыл бұрын

@BlaserBuilds it sounds like metal planetary squealing accelararing noise. Like when big bus trying to accelerate hardly.

What kind of pan is that? Nice followup vid BTW.

@BlaserBuilds

Жыл бұрын

Stock pan

@brianhavinga295

Жыл бұрын

Stock early 80e pan. They hold a bit more and use a slightly different filter

Where do u find the time to do all this? I can’t even go in my garage for a beer without getting looks!

@BlaserBuilds

Жыл бұрын

I was doing youtube and working on cars before we met, so it's kinda always been the way. But consistency is big, do a little bit every day, or as much as possible. After work(10 ish hours) I can get in like 2-4 hours a day without really interfering with any family time, or house work throughout the week. This teardown, and editing the video was maybe an hour and a half.

@twiztid83222

Жыл бұрын

@@BlaserBuilds Well after my work is done at 6:30pm 12hr day. Come home watch my son while she cooks then we eat. Then she takes 1hr to clean a kitchen with 5 dirty plates. 🤷‍♂️ 😴 I’m still looking for a c10 project but ppl want 15k for a junker. You should upload a old video of when you first started doing car audio lol. I miss my old systems but I rock a van now. Still have it in garage.

@BlaserBuilds

Жыл бұрын

@@twiztid83222 I do have a ton if old audio content. Lot of them in the playlists on the channel.

@twiztid83222

Жыл бұрын

@@BlaserBuilds I just watched a few earlier. Very cool to see 10yr old content I grew up on

Crazy that thing was still a stock ecu

@funfun8095

Жыл бұрын

It's not an auto shift.

@BlaserBuilds

Жыл бұрын

Yeah, and same SBE in the car for like 4-5 years.

@brianhavinga295

Жыл бұрын

​@@funfun8095 it was for 99% of the time

@funfun8095

Жыл бұрын

@@brianhavinga295 I thought that T brake was manual only...so ecu wasn't controlling shifts. I thought only Jake and CK had auto shifting T Brake VBs.

@brianhavinga295

Жыл бұрын

@@funfun8095 correct but it only had that. Valve body for a few months for 5+ years it was autoshifting running low 9's foot brake only

We’re are u located at

@BlaserBuilds

Жыл бұрын

Wisconsin.