3d Printer Automatic Bed Leveling - 6 steps to perfection!
In this video I'm going to show you how to level or tram your bed, set a bed mesh and set your z height on a 3d printer with a bed probe.
You may be surprised to hear that you still need to level or tram your bed when you bought a 3d printer with 'Automatic bed levelling'. Well unfortunately, this is very likely to be a little white lie that 3d printer manufacturers tell to make setting up the printer sound easier.
What 3d printers with a bed probe can do is create what we call a mesh that enables the nozzle to follow any variations in the surface of your bed after you have aligned it. However, there is nothing automatic about this process, we have to initiate it and tell the printer what to do next. Today. I'm going to show you how to do all this.
..............................................................................................................................................................
BUY ME A COFFEE
If you're enjoying my content, why not consider supporting the channel by buying me a coffee?
Even very small amounts are greatly appreciated and re-invested into bringing you better content.
www.buymeacoffee.com/rickyimpey
You can also use the KZread 'Thanks' button above if you prefer.
...............................................................................................................................................................
Affiliate links (If you purchase something after clicking any of the below links I may earn a small commission at no cost to you. This is a great way to support the channel)
Feeler gauges
US amzn.to/3CWBYMR
UK amzn.to/3ldaufM
Ender 3v2
US www.geekbuying.com/go/6hfPfc9d
UK www.geekbuying.com/go/6hfPfc9d
Artillery Sidewinder X2
UK affiliate.geekbuying.com/gkba...
US: bit.ly/3Nxj3hM
EU: bit.ly/3Q5T4zz
Timestamps
00:00 - What is Automatic Leveling?
01:00 - Manually Tram Your Bed
02:48 - Check Your Bed Probe
04:02 - Powered Bed Leveling
04:52 - Create Bed Mesh
05:40 - Zero Z Axis
07:10 - Slicer Start G-Code
Пікірлер: 348
This makes up for the 300 bad guides on youtube. Thank you Ricky.
@RickyImpey
Жыл бұрын
Thanks👍
@aofcole
3 ай бұрын
I agree and am not sure how all of the video I've watched are having good prints because they are using a feeler gauge but not explaining the offset!!! @@RickyImpey
Not all heroes wear capes.. some level printer beds and tell us about it. THANK YOU SOOO MUCH for this video!!!!
@RickyImpey
Жыл бұрын
Ha ha, thanks for the awesome comment 👍
You have no idea how helpful this was as a complete newbie to 3D printing
@RickyImpey
Жыл бұрын
Glad it helped 👍 Thanks for the comment
@aarontaylor7750
7 ай бұрын
I second that, i was having a complete nightmare getting bed levelled until i saw this video.
This guy should win a frickin' Nobel prize, the peace of mind he gave me after I finished the leveling deserves it...
One of the most well explained and clear understanding video on bed levelling. Thank you
This video turned my FDM printing experience upside-down. I was moments from giving up, after weeks spent trying to fine tune my CR-10s Pro V2 only to constantly have terrible first layer adhesion issues. I regret not finding your video before: all this time, I've been setting my Z offset wrong! 0.2 mm from the bed, when it should be touching. Also, the gantry wasn't fully level. Right now I'm running my first ever smooth print: little to no stringing, everything sticking to the bed without the need to use rafts... FINALLY! It looks like I can finally enjoy this hobby! 😂 I won't ever stop thanking you for this insightful video!
You don't know how thankful I am to have found someone who is actually HELPFUL! thank you!
Thank you!!! I was fine with manual leveling, and then was frustrated tremendously once I added CR Touch to my Ender 3 Pro. Updated the firmware to Marlin 2.1.x and followed your video and I’m getting excellent results! Keep up the great work!
This is hands down the best bed-levelling video I have come across. I do this every time now I get a new printer. Unreal stuff.
@RickyImpey
Жыл бұрын
Glad you enjoyed the video Christian. Thanks for the comment 👍
Cant say thank you enough, have watched so many videos where there was misinformation about the z offset. I applied what you showed in this video and instantly had perfect bed results. Thanks!
@TheNexGFXDesigner
4 ай бұрын
Exactly! Couldn't be more appreciative.
this guide is perfect man.... every 3d printer manufacturer should just include a link to this video in their user manual.
Once again we have a brilliantly simple and understandable explanation. Thank you!
Rick, thanks for your vídeo. I'm a at 3D Printer, bought a CR-10 Smat Pro and before this vídeo I was 15 days suffering with this problem, almost sending my printer to some place to check what's happening. I followed all your instructions and now it was perfect. You changed my life, really... thanks and keep doing this amazing work, please!
@RickyImpey
Жыл бұрын
Awesome, I'm glad my video made the difference👍
Just bought X2 as my first printer, with these tips got everything adjusted properly and now it prints perfectly. Thank you!
@lolyouwontfindme6070
Жыл бұрын
Were u having stringy prints beforehand? I seem to be having issues with my X2 after adding this new PLA +
Whoa! Thank you so much for making a tutorial with your Artillery printer! It seems like no-one ever covers the slight differences with these, troubleshooting shooting them can be really frustrating sometimes.
This guide is phenomenal. So much good information in such a short, clear, and concise video. I had a bit of fiasco after updating the firmware on my printer and I've been having a hell of a time leveling it again. So many of the other guides out there had contradictory information. This video is absolutely fantastic.
THANK YOU!!!! After three months of not getting a single good print out of my new Ender 3 S1, I've decided to relevel everything with your technique - still the z-offset was too low by ~0.3mm for some reason at first (driving the nozzle into the bed), but after live-adjusting it I am getting a reasonable first layer. Gone are those endless nights of levelling!
@youssefessamshawkyabdelgha3214
Жыл бұрын
Hello, im having trouble leveling my ender 3 s1, youve got the same model. Can j contact you whenever you're available and ask you some questions about leveling the bed? I have been struggling for quite a while. Thanks
@akaiphone
10 ай бұрын
did you use Z3 or Z10? i see both used on different forums. i am about to burn my printer down because the bed is never leveled. i didnt know i had to save the mesh and call it in cura. ender 2 s1 instructions never mentioned it
Hey Ricky, thanks for this wonderful video, now I see why I hated my BLTouch, apparently I was using it in a wrong way. I've updated my firmware and enabled the bed leveling menu and following your directions I now got excellent first layers again, thank you man. Always a big fan of your videos 👍
@RickyImpey
Жыл бұрын
Thank you for this comment, I love hearing how one of my videos has helped fix a problem or helped someone understand something better👍
I've been battling an unlevel bed and the cr touch since the beginning of January and have not had an success. I've tried many different videos of tutorials and none have worked. Running the bed level now and hopefully this is the video that has saved me from this everlasting nightmare
thank you for that video ! Recently i bought artillery x2 printer and after some time i had issued with bad bed leveling. After your clearly instructions everything works brilliant ! Thank you.
Wanna give you a HUGE thanks for this video! I've been printing for over a year now. First printer the CR6-SE. Recently ran into problems where I could get NOTHING to stick, even on glue and hairspray. I levelled and relevelled so many times. Watched more and more levelling videos. Eventually I was so defeated I bought a Ender 3 S1 Pro. But again, I couldnt level it! Prints were warping from the plate and i swore on my life I had it levelled. You are the ONLY person who has gone over levelling a printer that has addressed the Z offset. I had been setting it as far as the paper/feel gauge. I had NO idea it was meant to be touching the bed! After doing this, and adding that gcode in, the warping is fixed! I have subscribed because you for sure deserve it. Now I will be able to level my CR6-SE and have 2 printers going =0 My only gripe with the S1 Pro is the .05 z adjustments, wish you could go finer with .01. I had to choose between the nozzle being about .02/.03 above the bed or lowering it an extra .05 and touching. I've only tried it lower and it worked. At this stage I'm too scared to adjust it up and screwing things up. Anyways, thank you so much!
@RickyImpey
Жыл бұрын
Wow, what a great comment, thanks! Nothing motivates me to make better content more than hearing how something I've said has helped someone. I'm so glad to hear that you can now use your printers as you want to. Thanks for taking the time to comment 👍
Thanks a lot!!. I was not aware of the function of adjusting the Z axis by touching the bed of the printer. An essential video to calibrate your printer like a pro.
I cannot thank you enough for taking the time going through the steps of this process. Being new to the 3D printing hobby I have relied heavily on KZread videos and feedback from friends and other 3D printing enthusiasts. I have found in most cases the feedback or videos where like drinking from a fire hose. Either they are using software, hardware, filament, and calibrations that are outside my experience or they forgot what it was like to be new to the hobby. They unintentionally skimmed over some key areas or went too in depth in areas I am not even ready to jump into. I also found due to what they are printing compared to what I am looking to start with were another contributing factors in my failures. I gave up on my Ender 3 Pro and was thankful your example was relevant for me. I upgraded to the same sidewinder and it was refreshing to see someone walking through the process. It helped explain contributing factors as to why I was failing with my existing printing and configurations. If you ever need another topic, I could use help printing miniatures for table top gaming. The smaller the miniature with detail is, the more obstacles I have faced. I have been told resin is the way to go, but unfortunately I don't see purchasing the printer and required accessories in the near future. Thanks again for a great video and look forward to new content.
@RickyImpey
Жыл бұрын
Thanks for your comment. It's great to have feedback to help me know if i'm pitching the videos correctly. I know exactly what you mean about the fire hose of information in many videos. Very often it's just too much to follow. I will give the miniatures some thought, it's not really my speciality but some do manage to get good quality with small details on FDM machines. The first thing i would recommend would be trying a smaller nozzle like 0.2mm. That can really help but remember to change your slicer settings accordingly.
@mathieuborovic
Жыл бұрын
@@RickyImpey I appreciate the suggestion and placed an order for 0.2mm nozzles. I made a note to update the slicer settings once I install the smaller nozzle as well, thank you. I am going to spend the next few days going through your catalog to see if you already covered some of my pain points with miniatures. Adding supports, speed of print, angle of the item versus the bed and nozzle, etc. etc.
Thank you for all of your videos, they are the reason I'm now printing smoothly on my ender V2 with CRtouch. I did not have to watch any other videos besides yours and the process was very straightforward and enjoyable throughout with your help 👍🏽 Much appreciated.
@RickyImpey
Жыл бұрын
Thanks for this comment Kyan. Hearing that my videos have helped anyone is all the motivation I need to keep making them👍
@HeyKyan
Жыл бұрын
@@RickyImpey You are most welcome Ricky! Keep up the great work, it will take you far 👍🏽
So the probe z offset has to be fully "touching" the bed 🤦 god I was about to go mad 😂 thank you for the amazing video
I just want to say that i am extremely grateful for this video. I run my modded ender 5 on klipper and completely changed everything but the frame at this point. Added CRTOUCH to my setup and could not for the life of me find out why i couldn't get a good first layer. Everything i did was working great for the infill layers but never for the first layer walls. After watching your video, specifically the part about the Z Offset. I learned the way klipper has you level the bed using BLTouch wasn't accurate enough for my printer. Zeroing out the nozzle to touch the bed fixed my problem and now I'm getting insanely beautiful first layers. Thank you SO MUCH!!!
Great video very clean and clear instructions and helped me setup as a beginner thank you!
Thank you! Your instructions are the clearest for me out of all the others.👍👍
Excellent video! I´ve been leveling my Ender 3 Neo for the last week, following several videos with no luck, until I found this one! The best-of-all-print-leveling-video.. I followed it to the letter and I´m finally printing with great quality! The final and crucial tip was to save the mesh to the slicer (in my case Prusaslicer). It kept the leveling through all my printings. Thank you very very much! You gained another subscriber!! Greetings from Argentina!
@RickyImpey
Жыл бұрын
Awesome! Glad the video helped, welcome👍
A BIG THANK YOU FROM VENEZUELA I WAS HAVING TROUBLE LEVELING MY ARTILLERY X2. GREAT VIDEO.👍👍👍👍
Your method makes the most sense in all of youtube
Thanks Sheldon. Super informative tutorial.
Great video! Very clear, and helped me a ton to setup my sidewinder x2
You are a genius! I have lots of problems adjusting my printer, this is the best solution ever, thanks!!!
Thank you so much Ricky. I didn’t even know that the nozzle was supposed to actually TOUCH the bed surface when in the z offset menu!
2 months trying to figure this out... you helped me so much friend. thank you! cheers!
OMG Thank you so much! Your explanations were so clear and consise, it works great now!
This worked so well on my Artillery X2. Brilliant step by step and has really helped me learn a lot. Thankyou.
Just came by a new to me Artillery Genius Pro where I replaced the glass bed. This tutorial could not come at a better time for me. Thanks to the creator and the algorithm for suggesting it now.
At last! This is exactly right. No myths or magic nonsense, just pure engineering.
I am soo soo happy i found your video Ricky. .it's very comprehensive and very well explained in very easy to understand stages. I've been struggling to get my v1 Cr10s-pro bed calibrated. I think you are the only one who had explained the importance of Stage 5 Zero Z-axis!! My hotbed is now kaput but with your guidance I am still able to achieve a good print. THank you very much!
@RickyImpey
Жыл бұрын
Glad the video was helpful👍
I had a warped heat plate on my Ender 3 and ended up having to replace it. Before going back to the headache of re-leveling all over again, I watched this video and since following this advice, my prints are 1000 times cleaner and I no longer have to re-level the machine between each print. The Gcode advice to edit in Cura was an absolute lifesaver. Thank you for providing such helpful information! You're a printsaver!
@RickyImpey
Жыл бұрын
Awesome, really glad the video helped👍
@someotherdude
6 ай бұрын
There's an easy fix for this. Simply place 1 or 2 squares of ordinary paper under the magnetic PEI pad right in the center of bed. That's where the dip is, once I did this, I was able to place a ground steel bar on the bed (actually on top of the PEI) and it's now perfectly flat. I used a 3" square, on another printer I used a 6" square on top of a 3" square. I have 3 of these printers, all 3 had same issue.
Quality of your videos are incredible!
@RickyImpey
Жыл бұрын
Thanks 🙂
Thanks my friend. I learned many things that I am going to apply to level the printer well. Thank you so much
OMG THIS VIDEO SAVED ME AFTER HOURS OF FRUSTRATION! Thank you so much!
thank you for this in detail explanation
Great video! Wish I had seen it before I started 3D-printing, has a few important steps that are omitted in other guides, including from the manufacturer! Thanks Ricky.
@RickyImpey
Жыл бұрын
Glad it helped 👍
Beautiful. I just bought my CR Touch and am looking forward to installing it.
I wish this was the guide I first looked at when I got my X2.. I have a few bed scratches rn lol. Perfect guide tbh.
Thanks for the step guide… your are saved me a lot of frustration… 🤩👍🏼 I also checked the excentric nuts on X and Y axis before step 1…
This is a VERY good video! So detailed it's PERFECT! great stuff Sir
@RickyImpey
Жыл бұрын
Really glad it helped.
best guide ever!
Hey Rick Thank You so much for step1,step2,step3,step4,step5 & step6 WoW THE End!!
Hey Ricky,, Because of your help I was able to print 3d crocodile 😀 Thank you so much
Thankyou so much you have literallly just saved my business......
So helpful (and life saving ;-) ) thanks Ricky
Excellent video!
extremely helpful, thank you!
Hands down THE best guide. So many other lead people astray
Superbly clear! Thanks for your efforts. X2 on the way, so this will save me lots of time...
hello, great video on a useful topic, thanks for sharing your skills :) 👍
Just wanted to say a massive thankyou! Been trying for ages, this methode worked!
@RickyImpey
Жыл бұрын
You're welcome!
I got my new printer last week. I plugged it in and ran off some perfect prints. Then I watched some videos and decided to make it better. It took me awhile to get it back the way it was 🙂
This was soooooo helpfull thank you soooooo much
Creality should just link to this video to level beds and pay you for it, their video made me drive the nozzle into my glass bed. Going to re-level using this method, thank you so much for this.
Amazing guide!!! I found it extremely helpful and it helped me finally use my CR Touch properly!! Print are coming out great now. Thank you
@RickyImpey
Жыл бұрын
Awesome👍
Great guide!
I’ve had my genius pro since June and level has been my worst enemy. This video was an exceptional amount of help. Not just in the level process but so much off what settings are for, do and how the Z hight adjustments on Artillery specifically work Cheers
@RickyImpey
Жыл бұрын
Really glad it helped 👍
You Sir, deserve a subscribe. Pleasent voice and on the point. I keep forgetting that Z=0 should be just that..0...Printing PETG on my new PEI sheet like it was peanutbutter on toast.
This is an amazing video. Thank you for making it. If you have some extra time please do one with a Sovol SV04 , it is a pain in the ass to level this printer. It took me hours. But after watching a video I was able to make it. I can't thank you enough.
Thanks for the information, specially the GCODE part, its explained why my auto leveling not working
Very helpful, thank you.
Thanks a lot, started working with the genius pro which worked fine out of the box until it didn't. Just mesing with settings did not help. got it working now thanks to your video!
M420 S1 is a game changer! Thank you so much! I always knew that the printer doesn't use bed mesh and I had to tune the first layer every time. The problem is finally gone.
@RickyImpey
Жыл бұрын
Awesome, glad it helped. Creality have said that they have configured the firmware so that the M420 code is not needed but so many are finding that it is.
bro i LOVE you! Thank you from the bottom of my heart. I'm very new to 3d printing and this video is a lifesaver!
@RickyImpey
Жыл бұрын
Awesome! Really glad it helped.
This is amazing and enlightening video. I didn't understand the concept of Z-offset, but this video explained it to me! I was suffering with bed levelling on my Ender 3 V2 for sooo long, but this fixed for me. Although, another newbie mistake - I hade G28 AFTER my M420 gcode, which, from marlin docs: By default G28 disables bed leveling. Follow with M420 S to turn leveling on. So basically I was trying to print stuff without having the actual mesh usage enabled :D
This video should be labelled as "Public Utility". I already had a printer without a bed probe but I bought a Ender 3 S1. I had trouble understanding how the Z offset worked and the mesh (I flashed the Marlin firmware). The mesh didn't seem to work because it printed too low or too high depending of the places. I followed your tutorial step by step and it works perfectly ! Thanks a lot ! I don't understand why the M420 line isn't here by default on Cura but now I have it ! Thanks again !
@RickyImpey
Жыл бұрын
Thanks for the comment, really glad the video helped
Beautiful.
wow, i didn't have the gcode lines so it was just printing on the very rough level i set thinking the bltouch would refine from there. also didn't know the nozzle was supposed to be touching the bed. good video!
@RickyImpey
Жыл бұрын
Glad the video helped Ray. Thanks for the comment 👍
This has to be, hands down, the most comprehensive guide for bed leveling, tramming, setting thatz offset and getting a perfect first layer overall. Sadly, almost no printer comes with a firmware that makes it easy to set up, but for all of you who have an Ender 3 Series Printer, Profesional Firmware has some auto tramming capabilities that semi automate the task, and can generate bed meshes of up to 9x9. Following this guide with such a firmware definitely will make for a perfect leveling, every time.
TIL that I've never been using my printer's generated bed mesh because I didn't have it set to do so in Cura (*smacks forehead*). Thank you for this video lol
Thanks for this mang..
That's for the good videos,I have learned a lot from them. Could you PLEASE do a video on how,and what parts you used to connect the 2 z rods together, thanks
got my first printer two weeks ago, did some test cubes and a benchy which were decent. after that i set out to conquer the torture toaster with no luck so far. i failed 6/6 attempts, and those were all due to wrapping after the 3rd or 4th layer. now i set my printer according to this guide, and i'm ready to try again, wish me luck!
@shimonthepro
Жыл бұрын
Update: worked like a charm, thanks!
been having issues. this is a game changer
I have just ordered the X2 printer. Your video has just saved me an enormous amount of grief.
Thank you for this video been printing for 2 years and I still learned so much watching this that I didn’t know could you maybe do a video on printing silks with a Boden tube I’d love to see your opinion and your help( I have the fabled extruder click issue
This video literally saved me from completely giving up on 3d printing. I had my printer working perfectly for months then 1 day boom it stopped working. No matter how many times I leveled it and changed settings, it was always the same thing. Followed this code guide and boom it’s perfect. My only question is why did it work perfectly fine for multiple prints and then all the sudden go crazy?
I watched a tutorial already on how to level the bed, but thanks for confirming that I'm not crazy lol. I thought it would just level itself with the push of a button. When it started printing half an inch above the bed surface I then did some googling and youtubing and found you still have to manually level the bed.
@RickyImpey
Жыл бұрын
Yes, unfortunately calling it 'automatic' bed leveling is a terrible idea.
I had a printer that was inconsistent at best with saving its zeros. I never did the leveling by disengagin the stepper motor because I had the auto leveler. I was a fool. This video has fixed a long time problem and hours of my life. Thank you.
@RickyImpey
Жыл бұрын
Awesome 👍
Thanks!
Thank you
Thank you for the detailed tutorial. My printer is now perfect.
@RickyImpey
Жыл бұрын
Awesome, job done🙂
Thanks for a awesome video, really well explained. 1 sub earned.
@RickyImpey
Жыл бұрын
Glad it helped
Thanks!!! I originally followed the wrong tutorial. It advised me to have a gap with the Z Axis. I'm instantly printing much better!! :)
@RickyImpey
Жыл бұрын
Unfortunately there is lot of incorrect information out there. Glad you found the video useful.
I wish I had seen this video before trying to level my X2 out of the box. Hopefully, whatever I have already done is recoverable! Thanks for posting.
@RickyImpey
Жыл бұрын
I'm sure it will be fine👍
quality content right here! Thanks a lot ) I am a little bit tired of G29 every time and I have an answer now! :)
@RickyImpey
Жыл бұрын
Great, glad to help.
Thx. I always was close to a perfect lvl but now I learned that the nozzle has to touch the middle. This was the last puzzle piece.
thanks!
Dudddeee... thanks for the M420 S1 Z10 code! I always thought that bed leveling for each print was completely unnecessary!