This turned out amazing I’d buy this

@yasirsafarudin596

13 күн бұрын

Where to buy?

Just finished printing on an Ankermake and here are some thoughts: 1) printed at 103% and still too ight. Probably need to slice it at 105% to fit my head and might ruin the seamless main face plate. 2) Since it's tight, any slight movement would separate the magnets and plates. Some magnet slots are too deep and couldn't attract/attach in place. Ended up gluing velco in between the magnets to hold the entire helmet in place. 3) many zits on the side plates (Filament sucks compared to resin) and I might have to do some careful sanding and eventually repaint, which defeats the purpose of the textured outer walls and colored filaments. Lots of failed prints and more $ than I anticipated. Overall, very great project overall. Well worth the money for the file.

I've been looking for this for a while... Just bought the files, and I'll be printing this soon!

@dongxiaoli

8 ай бұрын

Could you share me your files， I really want it, but I can't buy it

@mrsant0s

7 ай бұрын

How did it come out? I'm having trouble getting it to fit on my ender 3 v2.

@mrsant0s

7 ай бұрын

How did it come out? I'm having trouble getting it to fit on my ender 3 v2.

@JOSEALVAREZ-yu4mf

2 ай бұрын

@@dongxiaoli Did they share the file with you if so can you share?

amazing

@3dprintsthisweek

Жыл бұрын

Thank you! eSUN has always done great for us!

Podrias ayudar con cuanto del porcentaje se puede escalar el casco para una persona adulta?

Can you share your settings? Im using cura and its saying 4 days and 700grams of filament for me just for the main front piece

Turned out great! I'm currently trying to slice this myself and I'm struggling to find a good position for the middle section with minimal supports. How did you position yours? Thanks

@3dprintsthisweek

Жыл бұрын

I had my chin and back as close to the build plate as possible. I had tree supports set on 70 for overhang. It didn’t come out perfect, the chin was a little rough underneath. But hardly noticeable. The top of the head also got a little of the circle pattern.

@grahamkeys

Жыл бұрын

Thanks for the reply. I wasn't sure if positioning it nearly straight would have been better. I'll give yours a go. Thanks very much!

What size printer did you do this on?

Great work. How did u prep it in the slicer? Cant seem to get a good outcome.. TIA

@3dprintsthisweek

Жыл бұрын

I used the stock "super quality" in cura and adjusted the speed to be slower. I used tree supports as well.

Hello i bought this file but it becomes Pastaization at the middle of project with tree support which filament are u using i couldnt make this mask with my p1s :(

what size do you recommend for 7 1/8” head size?

did you print it how it loaded in the slicer? upright. trying to figure out the best position to avoid any weird spots cause of the texture pattern, i cant sand it back.

@3dprintsthisweek

8 ай бұрын

No, I adjusted everything to stand as vertical as possible. The only part I couldn’t avoid was under the chin.

What orientation did you print the main front piece at? I dont want the get that swirl look when printing when it gets towards the top/end. Yours came out amazing!

@3dprintsthisweek

Жыл бұрын

So that’s the tricky part. I do have a bit of a swirl on the top of mine. I found the best way to get the fabric texture to print, is to have everything as vertical as possible. I didn’t want to sacrifice the front so I took the hit on the top. Close up you can notice, but it still looks great from a normal person to person perspective. I had my chin close to the build plate. That’s the other part that had some rough spots. I printed pretty slow too, that gave me better results. Hope that helps, good luck!

@Xaqted

Жыл бұрын

@@3dprintsthisweek very much, thank you for the info! I love your work, keep it up!

This one turned out great! I actually bought the same filament and colour as you. Like you, I like it but i think I would also like to try it in a darker red too. I was just curios did you end up trying in in a different red? If so what colour did you find to be best ?

@3dprintsthisweek

Жыл бұрын

I haven’t yet. I want to. Just backed up on projects

@danielcoombes3310

Жыл бұрын

@@3dprintsthisweek I know that feeling. Got so many models to paint myself but i just cant stop printing

@justinesq.281

Жыл бұрын

did u find a dark red

Sensacional...... tambem estou começando na area de impressoes 3D, mas até acertar o ponto certo da qualidade velocidade e temperatura demora um pouco..... mas estão muito lindas suas peças, parabens.....

@3dprintsthisweek

Жыл бұрын

Thank you! It has taken me some time to figure it all out but I still really enjoy it. My kids have a great time picking out print projects too. Thanks for checking out the video, happy printing!

@stevek1959

2 ай бұрын

Brasil!!

It looks great, I use an Ender 3 pro. Can you recommend some tips for clean part? Thanks

@3dprintsthisweek

Жыл бұрын

If you mean, it printing clean, just try to have everything as vertical as possible. The fabric texture does better that way.

I was able to figure out how to orient everything pretty good but something I can't figure out is the eyes. How did you orient the eyes?

@3dprintsthisweek

Жыл бұрын

I actually did my eyes on my resin printer. If you’re doing them with pla, I would stand them as vertical as possible, with just a little lean for supports on the backside.

That looks great. How much red filament did this take? Would I get all the red parts printed with a kg? Thanks.

@3dprintsthisweek

7 ай бұрын

I’m pretty sure I got it all just under a roll. Never hurts to have an extra roll on hand though.

Stupendo! with Cura, how do I know what size to use for my head?

@mariospanayiotou6644

4 ай бұрын

i know its been a year but if you are still interested, there are some head files on thingiverse with various head sizes, you can put them in the slicer and see if it will fit.

Ich bekomme die Seiten teile nicht gedruckt 🤷‍♂️ kannst du mir zeigen wie du die gedruckt hast ?

Do u happen to know what is the difference between Low poly version: Front mid and Front low they look identical not sure what to use.

@3dprintsthisweek

Жыл бұрын

I’m sorry I don’t. I don’t see that option in mine.

Hi dude print looks awesome, did you have any trouble slicing the main part of the textured mask in cura? Keeps giving me an error and fails to slice, ive tried all different settings for it and using a different copy of the file to make sure it wasnt corrupted or anything. But i can slice the sides of the mask just fine. I get its a very detailed file but my computer is pretty beefy so it cant be that. Thanks!

@3dprintsthisweek

Жыл бұрын

That is so odd. Somebody else said they had that problem too. I sliced mine in cura with no trouble. I think they ended up using a different slicer. Which version of cura are you on?

@joshbailey4124

Жыл бұрын

@3d Prints This Week Yeah very strange. I'll have to download and try a different slicer. My cura appears to be version 5.2.1

@3dprintsthisweek

Жыл бұрын

@@joshbailey4124 That’s so strange. I’m on Cura 4.13.0 and I’ve sliced it several times. I would go for Prusa Slicer? That’s typically my backup. Sorry I couldn’t be more helpful.

@joshbailey4124

Жыл бұрын

@3d Prints This Week no its all good dude thanks for the quick replies 👍👍

How long did the main part take to print? Looks great!

@3dprintsthisweek

Жыл бұрын

I print pretty slow so a couple of days.

This is crazy!! Do you do commission prints for ppl who dont have a printer or know of a way to get this made elsewhere if you dont?

@3dprintsthisweek

Жыл бұрын

Hey! I don’t at this time anyways. You may want to check out Etsy though. I’m sure you’ll find some comparable. Thanks for checking out our video!

If you use cues what percentage size did you print at like the size of the helmet becuase I am working on my own and the print is constantly failing and shifting I print at 70 speed

@3dprintsthisweek

Жыл бұрын

I use cura. Mine was 100% size and the speed was 40.

@TRWwiszdom

Жыл бұрын

@@3dprintsthisweek what printer do you use?

@3dprintsthisweek

Жыл бұрын

@@TRWwiszdom Ender 5 plus

Can you make a tutorial on how to do the magnets like that?

@3dprintsthisweek

Жыл бұрын

The magnet slots are actually built into the design. All I had to do after I printed was glue the magnets in.

What support settings did you have for the side pieces? I’m using prusa and are painting the bottom and the arc on the top.

@3dprintsthisweek

Жыл бұрын

In Cura, I used tree supports. I positioned it as upright as possible but left a slight tilt for the supports to grab. I’m not sure what the prusa version of tree supports are though.

@Idgafwic

Жыл бұрын

@@3dprintsthisweek would printing it at 100% speed affect the fabric texture?

@3dprintsthisweek

Жыл бұрын

@@Idgafwic I would imagine so. I’ve only printed it slow though.

@Idgafwic

Жыл бұрын

@@3dprintsthisweek finished it, weathered seams with airbrush, incredible print.

@3dprintsthisweek

Жыл бұрын

@@Idgafwic congrats! I love that file.

Have you had any trouble with putting the magnets on the slots on the helmet? If so, what did you do to make the helmet a more snug fit for the magnets?

@3dprintsthisweek

Ай бұрын

I haven’t had the issue. I use super glue and pop them in. I’ve never had one fall out after.

@CarlosLopez-ie7tk

Ай бұрын

​@3dprintsthisweek ok cool, but what would you do in case the magnets you have were a little too big for the helmet?

How much spoils of red filament did you use?

@3dprintsthisweek

Жыл бұрын

Only one and had leftovers

Hi! How many fillament did you spend on this helmet?

@3dprintsthisweek

5 ай бұрын

I was able to print all the red within one roll (1kg).

did u ever find that dark red filament ur looking for i can't decide if this red is too bright for a dead pool mask

@3dprintsthisweek

Жыл бұрын

I’m still using ESun fire engine red.

@justinesq.281

Жыл бұрын

@@3dprintsthisweek i mean dont get me wrong the fire engine red looks so pleasing but u know perfection is better. ill try the fire engine red

@3dprintsthisweek

Жыл бұрын

@@justinesq.281 totally agree. I just couldn’t find something closer that I liked.

What layer height and nozzle size did you use!

@3dprintsthisweek

Жыл бұрын

0.4 nozzle, height 0.16

Heyho, the mask looks great! I purchased the files on DO3D as well, I have some issues slicing the files in Cura. I always get a message that the slicing failed. Maybe you can help me? I Use the actual Cura SW 5.2.2 on my MacBook. My Printer is an Ender 3 V2 Neo. I would love to read from you. Thank you and many greetings.

@3dprintsthisweek

Жыл бұрын

That is so odd. You’re not the first to have this problem. A few other people told me they had the same issue. I’m on an older version of cura 4.13 and it didn’t give me any issues. It must be something with the updated version of Cura. I’m not sure if anyone has found a work around or if they just did the file in a different slicer.

@MOE13576

Жыл бұрын

Use a different slicer

I have the file but when I try to slice it in cura 5.4.0 it gives an error message. Any thoughts on why this is?

@3dprintsthisweek

10 ай бұрын

I didn’t have that issue, but other people used a different slicer and it worked. Some even downgraded cura and it worked.

@bradtbickford

8 ай бұрын

Ditto what the creator said, I had to upload version 4.13 to get it to slice, but now having problems getting Cura to work with my sonic pad. Presa also works, but I haven't used it before so I'm having issues with my printer.

@JOSEALVAREZ-yu4mf

2 ай бұрын

Would you share the file please

Can you breath? My only doubt is... how many minutes can you wear it?

@3dprintsthisweek

3 ай бұрын

I wore it for a couple of hours on Halloween. I got pretty warm but I was able to breath.

Hola bro, tengo un problema. Compre tu diseño por tu página de internet y no se puede segmentar. Tengo una Creality Ender Max Neo ¿Que puedo hacer? Espero tu respuesta muchas gracias

@3dprintsthisweek

11 ай бұрын

Hi, it's not my file. I just did a video showing where to get the file. I'm not sure what you mean, it can't be segmented. Are you trying to cut it into pieces?

@user-gt8qx7vs1y

11 ай бұрын

@@3dprintsthisweek Gracias por responder hermano. Lo compré y al momento de querer imprimirlo me salió un error, la impresora que tengo es Creality Ender Max Neo, no intente cortarlo solo al quererlo imprimir sobre todo las piezas más grandes, me salía un error que no me permite imprimirlo, pero las piezas de menor tamaño si se pueden y no me sale el error. Algún consejo que me puedas dar para ello, o podrías explicarme cómo fue que tú lo imprimiste??

@3dprintsthisweek

11 ай бұрын

@@user-gt8qx7vs1y I would try to use a different slicer program to create your g-code. I think other people had the same problem and when they used a different program to slice it, it worked. Hope that helps.

Sir can u please tell me the total weight of this mask?

what orientations did you printed everything?

@3dprintsthisweek

5 ай бұрын

I did everything as vertical as possible. The sides and back needed to be straight up and down to get the best out of the fabric texture. For the main piece, as you can see in the video, I couldn't avoid some the chin getting messed up. I positioned that part with the chin touching the build plate. I will say, I printed again on the x1c since I made this video and it came out even better. Hope that helps.

Please someone tell me what is the material off the eyes Made of

@3dprintsthisweek

Жыл бұрын

www.amazon.com/gp/product/B007KGDV3K?ie=UTF8&psc=1&linkCode=sl1&tag=3dprintsthi00-20&linkId=c4e68abf30dd331b743555ee0f4489e5&language=en_US&ref_=as_li_ss_tl

@maxmum9118

Жыл бұрын

@@3dprintsthisweek that is funny 🤣🤣 any way thank you for the amazing idea you made

Would an ender v3 SE print this?

@3dprintsthisweek

8 ай бұрын

The bed size would probably be your biggest problem.

What layer size U use to get thst result ? 0.1

@3dprintsthisweek

Жыл бұрын

Been doing .16 lately for best result

Hey ! how can I get the desugn of it ?

@3dprintsthisweek

4 ай бұрын

Do3d.com

What printer did you print on ?

@3dprintsthisweek

7 ай бұрын

Ender 5 plus at the time of the video. I have a Bambu x1 carbon now and it’s soooo much easier.

Can you print this on an original prusa

@3dprintsthisweek

2 ай бұрын

I haven't used that printer, i'm not sure.

Did you had to support the very top of the helmet?

@3dprintsthisweek

4 ай бұрын

I did back when I made this video. I had printed it on the ender 5 plus. I’ve tried it again with no supports in the top middle on the Bambu carbon, it still came out great.

@onurpekcetin7260

4 ай бұрын

@@3dprintsthisweek oh I see. Thats a strong af printer. I'm not sure my elegoo neptune 3 pro can do that

Hey man. Do you have any clue why i keep having trouble printing out the sideds ?

@3dprintsthisweek

Жыл бұрын

What’s happening?

@MOE13576

Жыл бұрын

@@3dprintsthisweek ok, so I printed out the main mask at 105.68%. Then i printed out the one side at 105. 68%. But it came out smaller, where it don't fit the main mask accordingly.

@MOE13576

Жыл бұрын

@@3dprintsthisweek I know I probably should've scale the >whole< helmet first and then printed out separately. But I'm not sure how to do it. I tried using blender after the 2nd failed attempt, but It's kind of confusing

@3dprintsthisweek

Жыл бұрын

@@MOE13576 Do you have uniform scale on? Meaning are you sure all x, y, and z scaled up to the same size? If not, I’m stumped on that one.

@MOE13576

Жыл бұрын

@@3dprintsthisweek yes. Well thanks for replying anyways

Can you make one for me brother ?

what size are the magnets?

@3dprintsthisweek

Жыл бұрын

amzn.to/3hDQx37

@lmntrixxx8487

Жыл бұрын

@@3dprintsthisweek thanks!

@maxmum9118

Жыл бұрын

Man I love you You deserve 29M subscriber Very helpful

Im new to 3d printing i apologize if i sound like a newbie. Will a ender 3 print with that texture?

@3dprintsthisweek

9 ай бұрын

No worries, we are all new at some point. I think it could handle the texture but fitting it on the print bed might be a problem

You sound like the guy from Auction kings(TV show) hahaha

@3dprintsthisweek

Жыл бұрын

😂😂😂

@MOE13576

Жыл бұрын

@@3dprintsthisweek hey man. Your mask came out dope. I'm in the process of printing the face (?) Currently 85 hrs print time😮‍💨

@3dprintsthisweek

Жыл бұрын

@@MOE13576 nice dude! I still randomly run around my neighborhood in mine.

I need the 3D file to make mine, please

@3dprintsthisweek

5 ай бұрын

I don’t have the rights to give the file away. It’s a paid file from Do3d.com

@briansanchez1014

5 ай бұрын

@@3dprintsthisweek i'm from Colombia, soy colombiano por favor

How do i get it

@mariospanayiotou6644

4 ай бұрын

I sell them if you are still interested

@mariospanayiotou6644

4 ай бұрын

I mean the finished product not the file, file is from do3d

@valentinorossi7823

4 ай бұрын

I want finished product mate

I bought this last night and printed the eye pieces. Total mess.

Hi there so you printed at 100% I was curious if you knew the circumstance in inches for your own head, I’m 23ish inches but I’m struggling trying to figure out what I should safely scale this to 😅 if anyone else has any knowledge feel free to send it my way, thank you!

@3dprintsthisweek

8 ай бұрын

I’m 24 and it’s tight on me. It fits, but tight.

@VeskiTrolli

8 ай бұрын

@@3dprintsthisweek understood I’ll definitely scale up a little then, thank you very much!

Please send me free link stl please

@3dprintsthisweek

Жыл бұрын

Link is in the file. It’s not free. Gotta pay like everyone else 🤷‍♂️

It looks fine just give it a black wash