Exactly the comparison I wanted to know between these 2 products with the lake country Orange pad. Excellent video. subscribed!

@YettiAutoDetailing

3 жыл бұрын

Thank you for the support 🙏

Koch Chemie’s products are top shelf. I’ve used them a lot this past year and best idea is to buy a gallon of the koch stuff if you correct a lot. Especially the M302.

Thanks! awesome review.

As You'd said,they're pretty even steven. I have 3d one....not sure if I "need" koch chemie. Very good video. Liked/subscribed.

Both of those products are meant to use less correction fluid you could have gotten away with 2 smaller dots of fluid. The gentleman who is 3D chemist said you need less of their correction fluids than others. And at Kock chem training people were also told to use less.

@YettiAutoDetailing

3 жыл бұрын

Thanks for the tip I'll keep that in mind

@danlc95

3 жыл бұрын

Yes. Agreed.

awesome video and product review. seem pretty even.been using 3d1 4 over a year ago love it it's my go 2 product. Koch chemie little pricy and hard 2 get where 3d1 is every where.lookn fwd to next video.

@MUJHOOL

3 жыл бұрын

After the clay bar and before the kc 302 whats needed? I'm very beginner and I'm sure I'm missing something?

@mbrownn117

3 жыл бұрын

@@MUJHOOL After clay bar you need to get rid of any oils left behind to prep the panel for compound and polish. I use CarPro Eraser, wipe it on and wipe it off and your panel will be prep and ready to go to start correction. Also before clay bar its a good idea to use an Iron remover to prep for clay

@richardseem7948

3 жыл бұрын

@@MUJHOOL iron remover if needed, than panel prep than good 2 go to polish

Great vid and good comments. What's the light you used?

@YettiAutoDetailing

2 жыл бұрын

Thank you so much 🙏 It was a cheapo from harbor freight.

Which one do you still use today , im on the fence between getitng 3d one , or a combination of H6 from koch and the m3.02 as a combo?

@YettiAutoDetailing

Жыл бұрын

I use what I refer as the three wise men. Koch chemie H6, F6, and M3. I've found 3D one to be too greasy in my opinion.

I have a newer Chevy truck and the clear coat seems extremely soft on it, Koch chemie m302 is the only compound I’ve found that actually works on it, as far as finishing out nicely without making it worse than it was originally

@YettiAutoDetailing

3 жыл бұрын

I'm finding that not many products match up to the quality of Koch Chemie

@dreday77764

3 жыл бұрын

pappy232 What pads did you use to correct your paint and also technique used?

@pappy232

3 жыл бұрын

@@dreday77764 I used rupes fine and ultra fine pads, used a griots G9 on speed 4-5 with light pressure, overlapping horizontal passes

@dreday77764

3 жыл бұрын

pappy232 thank you so much for that. I ask because I have a Lexus ISF in obsidian black. Paint is very soft and has light to Medium swirl marks so was going to use 2 step correction: sonax perfect finish on yellow Rupes foam pad plus Koch chemie 3.02 on white Rupes. I also have lake country hydro tech crimson pad on hand in case for finishing if need be

@danlc95

3 жыл бұрын

Be careful with 3D 1, ACA520, AAT502, Meguiar's M205. They can potentially leave da haze, and/or tick marks on soft paint. I want to have only one line of polishes that work on a vide variety of finishes, and so far for me It's Menzerna. I just ordered the set of Kock abrasives. If they work better than the Menzerna, I'll gladly switch.

Do you think you could use M3 for a one step prior to applying a coating? Great video

@YettiAutoDetailing

2 жыл бұрын

Thank you so much. It ultimately comes down to the type of paint as each vehicle can be different. I would honestly use their F6.01 for 1 steps and Micro Cut more for polishing.

Great video. I’ll probably take some flak for this but I’m still trying to like 3d one. I’ve done 2 cars with it now with same LC pad and with the Uro fiber like every one suggests and I’m just not that impressed. Maybe after watching a few videos I was expecting too much. Does have great working time though. Keeping it up!

@YettiAutoDetailing

3 жыл бұрын

This was only the 2nd time I've used 3D. I did a paint enhancement on a Mercedes that had severe buffer trailes on it. I used a blue lake country pad and it came out mint. But alas vehicle is different thats why I keep a few different types at my disposal. Thank you for the support.

@jsno78

3 жыл бұрын

Yetti Auto Detailing no problem! I used it on a 2016 Lexus and older escape. Maybe I got a bad batch. Lol. I’ve got a test panel coming in soon and going to try a few more combos and I’ll go from there.

@jsno78

3 жыл бұрын

@@yanniobkirk5744 just didn’t get the results I was looking for. I’ve tried several different pads now & just think my expectations were too high. I’ve got a test panel coming and really going to work with it on that.

@danlc95

3 жыл бұрын

@@yanniobkirk5744 - This exactly.

How soft is the clear coat

@YettiAutoDetailing

3 жыл бұрын

I'm finding the clear coat on this to be fairly easy to work with. Not like most cars from Europe that have very hard clear coat or not as soft and finicky as Tesla. More middle ground. Hopefully that answers your question.

The time lapse was in real time

@YettiAutoDetailing

3 жыл бұрын

It was sped up but only to 2x the speed.

4:14 Not enough product!!!

@YettiAutoDetailing

3 жыл бұрын

That's odd as I've learned that both companies actually recommend less product.