I wouldn't worry too much about meticulously learning the DOL. In the am2 you are provided with a wiring diagram, so it is very easy to see where the link cable is missing from.

@GSHElectrical

Жыл бұрын

Thanks for the feedback 👍🏻

@slelectricaleducation129

Жыл бұрын

kzread.info/dash/bejne/fXpnuMNrqay7e7A.html

@sunshine3187

Жыл бұрын

My dol wiring diagram today went L3-L2-L1 from left to right. Not L1-L2-L3.

Very informative video on dol motor control. Thanks lads.

Thank you guys ,this is really helping

Perfect.🎉🎉🎉tnx guys😊

You are simply the best

@GSHElectrical

Жыл бұрын

Thanks for the support 👍🏻

Yes to when a GSH alert pops up.

@GSHElectrical

Жыл бұрын

😁👍🏻

@montystelevision3238

Жыл бұрын

@@GSHElectrical Gaz. I’ve had an interesting email regarding the pulling of service fuses

I WISH you would do a continuity test on this from a three phase board,there is no such thing on KZread😢

👌

👍👍👍👍👍

credit boys very helpful.

@GSHElectrical

Жыл бұрын

Thanks 👍🏻

What about VFD. Lots of new IE2 & IE3 3ph motors are designed to be run from single phase supplies via inverters. I'd like to see this covered as a video with some reference to the way this works and is wired up with starters and remote controls.

Just wondering could you post a photo of the single phase and the three phase DOL starter circuit diagram, would be handy to have when on site. Great video 👌

@GSHElectrical

Жыл бұрын

Motors, Starters, Controls, Remote Stop Start - Single and 3 Phase kzread.info/head/PL2Ea5r9gxUUfv51Ld1UlNGR39rfFIExTU 👍🏻

@slelectricaleducation129

Жыл бұрын

kzread.info/dash/bejne/fXpnuMNrqay7e7A.html

What is the benefit of using a contactor relay? Why not use 3 poles C32 Amper circuit breaker to use it as a switch for more simple schematics?

How would u go on testing this using R1/R2??

How would you wire a 415v coil with a pressure switch

Hi - I love your videos and they have been super helpful in helping me prepare for my AM2s, however I managed to fail my Fault Finding. I know there is some description of a fault where the motor is 'juddering' or something similar but I cant for the life of me remember what the fault was or how to test and then rectify it. Can you help me with this? Thank you!

@GSHElectrical

Жыл бұрын

Hi thanks for the lovely message. If a 3 phase motor was juddering it has lost one of it phases. Remember all faults on AM2S are found either visually or by dead testing. All the best and keep me updated 👍🏻

@laurabradley1857

Жыл бұрын

​@@GSHElectrical I passed by the way!! Thank you! Loving life as a fully qualified spark now!

@abdulseaforth6930

Жыл бұрын

@@GSHElectrical yes Gaz- I see. By losing one of the sizes, it’s out of balance so it won’t run so smoothly. It will make sense!

Not specific to Motors but if the motor was turning the wrong way, this is the result of 2 phases being crossed... is this Polarity or is polarity only when the Neutral is involved? Would I just say crossed phases/conductors? I think the terminology I used was wrong last time & I don't want to make the same mistakes!

Fist of all apologies about this, a question only vaguely related to 3 PH Motors! If a building has 2 Phase supply, how is the Main 3 PH &N Section/DIstribution board cabled from incoming 2 Phase supply ?. As i understand it there won't be 3 Phase available. You may guess I'm working on an old school which needs a rewire.

@temp06j723-pmeighttq

26 күн бұрын

Isn't a TX installed?

Is there a connection from terminal 18 to 14?

@GSHElectrical

Жыл бұрын

3 Phase Direct Online Starter DOL Wiring Diagram Connections Explained kzread.info/dash/bejne/n5eM2sqOkbjIaZc.html

Do you install a single phase motor on 3 phase in your am2?

@GSHElectrical

5 ай бұрын

3 phase