This has come a long way from a few questionable rails lined out on the floor.

@josebarrera4334

5 жыл бұрын

It sure has!! I can't wait to see the final product !!

Before you paint it you should drill out and put a washer over all your grounds, keep yourself from having to ruin any paint to make all the grounds

@homiesjdmnation

5 жыл бұрын

And Seemseal the whole bottom of the car! I made the mistake building a Camaro rear floor with just doing the inside and even tho I painted and rocker guarded it still rusted from rain water! I like this tip tho!

@immattbaskett

5 жыл бұрын

This X100

@danieldavidson8149

5 жыл бұрын

90 degree pneumatic grinder with a sanding disk it my favorite way to clean grounds

@PiezPiedPy

5 жыл бұрын

last thing you want to do is remove the paint from ground points, ya all need to listen to Dylan Mounsey

Don't use the Raptor liner under any paintwork. It takes a long time to "off-gas" and will crinkle the paint something fierce. MotionAuto TV used a similar bedliner product under the paint of his supra mirrors and they peeled right away and he had to strip everything off and start again. Awesome progress BTW!

@shona5512

5 жыл бұрын

He's talking about using raptor liner on the opposite side of the steel to seal any pin holes from the backside of it, then he can sand the face for the steel and paint it as normal and not have to worry about anything getting near the steel or the paint from the under side.

@marclopez9809

5 жыл бұрын

Same thing happened to my bed liner I used the Raptor product as well

@madmax2069

5 жыл бұрын

I wouldn't put that on any frame or body panels, it'll just trap moisture over time and will cause it to rust, seen many people do this and it ended up badly for them.

If you get a copper block and get behind those welds you can weld the holes closed on those spots you welded the patch panel to. The copper block will not stick to the wire weld from the mig welder. It works great for filling holes in thin metal.

I still remember all the haters saying this wasn’t going to work

@erroneousjoe1301

5 жыл бұрын

Not first but CLOSE

@kotsuumo

5 жыл бұрын

Well we won't know about funtionality issues until its moving, but whether its before or after sema, he's gonna have a car that's drivable, for sure.

@carfreak1024

5 жыл бұрын

@@wtfialreadydid you, your mom, and the other person that subscribes to your channel doesn't have a clue what it takes to undertake a project like this with no formal training to speak of. In other words your opinion is just as valuable as your contribution to society. You might as well never have existed.

@uncleandy7983

5 жыл бұрын

@@rsproductions5, I still have some shirts....

@derekdok

5 жыл бұрын

@Cruzredeye I think he is building a crusty sock at home.

2:11 so Erick’s hole isn’t big enough huh? 😂

@85square

5 жыл бұрын

just gotta widen it a little

@themidnightwoodpecker6667

5 жыл бұрын

He's going to nibble on it a bit that should be very effective 👍

@aarontena

5 жыл бұрын

Lube will do

@melody3741

5 жыл бұрын

He just needs a little practice.

@namefighter8426

5 жыл бұрын

I was looking for this comment. I wasnt disappointed by the fixes xD

I must say I was very sceptical about this to start with but now I cannot wait to see it painted and complete. Amazing work and video content.

@kruleworld

5 жыл бұрын

I agree. it's come a long way.

A hard coupla days work.... but that sill / quarter panel repair.... you got to re do it...just cut till you hit clean metal..even if it means making that whole sill section, it wont take long, and the payoff will be worth it. Even with fibreglass over it it will bubble up in no time...be a heartbreaker then... Well done, keep it up...

@kruleworld

5 жыл бұрын

Won't really matter since he didn't fix the inside panel with the 20c hole in it.

@AFREAKINGLEMON

5 жыл бұрын

its rusted under the paint. its done

i see other peoples videos on their cars like 'putting new floor mats in' or 'installing new wheels' , then there's these guys that almost complete an entire interior in one video... good work guys!

Incredible progress, this project is really coming together. So glad you took the time to do the floor boards.

yall deserve a vacation after this build

@ericbailey3331

5 жыл бұрын

It's called a week at SEMA 😅

@jimmytaco7211

5 жыл бұрын

And disneyland

@BisforBuild

5 жыл бұрын

im taking two!

Having a fan designed as a "puller" fan as a "pusher" fan won't help with cooling! Fan shroud/fan blades and motor are all designed to pull air through the rad!

@eslai

5 жыл бұрын

Pretty sure they just had that lying there to plug into the harness. Notice the cardboard was still in place. The fan will probably still mount to the back side in reality.

@kittonsmitton

5 жыл бұрын

Thats how it was mounted in the M5

@JusttheEdge

5 жыл бұрын

Looks like a pusher that turns clockwise.

The steering wheel has a clockspring in it and if the steering wheel was turned more than 360degrees it may have been damaged and also if the steering wheel wasn’t put back to dead center 180/180, the steering wheel will throw some codes when you plug it back in.

I may be totally wrong but I feel like it almost adds a cheap feel by not filling in hopes with welds. I just hate body filler for covering holes.

150% you need to dyno this car, not cut corners on the paint job and eventually put a full length belly pan on it. i really really really hope the entire frame and structural work is properly aligned so this thing just rips. this HAS to work. so stoked for you my dude

@groundshakersociety6637

5 жыл бұрын

The car is in limp mode I'd assume

@VancitySmokers

5 жыл бұрын

Sexist Chicken it is and he states that 10 times in the video but also says he’s sending the ecu to get remapped and tuned.

@VancitySmokers

5 жыл бұрын

when did i say it was going to be a good track car. its on bags. lol. all i said was that i wanted it to rip. but thank you for very ambiguous and random bits of information im sure everyone cares about.

@VancitySmokers

5 жыл бұрын

as of late he hasnt tuned his cars hes made or put time in to got back to builds and finish what hes started. i was just saying that this car should be completed.

@VancitySmokers

5 жыл бұрын

fast is in relation to speed. it has nothing to do with handling. funny drag racing cars are fast but they cannot turn a corner, so all of your assumptions amount to nothing broski. space rockets are fast, they do not handle. id definitely grab a dictionary, and look up the word fast while youre at it.

Shame there was no rust proofing on the now welded over chassis

Oh, man. I work in theatre. Sometimes you have a huge job and a certain amount of time to finish it. Sometimes it's too close to call. You work all hours, tipping away at the list, hoping you'll be finished on time. The stress is never completely overwhelming, but it's there every hour you work. A lot of creative decisions. I feel the exact stress watching these videos. God love you. It will work out, but I know exactly how knackered you feel right now. But it will be magnificent when it's done. Keep on trucking on, brother!

5 years later and I’m now doing my floor pans came back to get tips . Happy to see the boys still be together to this day 👌

Can't wait to see the final product! It's gonna be badass

@highsidemedia7559

5 жыл бұрын

MaxSpeed damn your out here commenting away on anything car related hahahaha

@samyymnsr

5 жыл бұрын

MaxSpeed my mans out here commenting everywhere like bro chill😂

Holy shit guys, this was an action packed episode, truly incredible and a real inspiration, keep it up.

15:20 Why is the camera footage tearing up like that ?? Just thought I would bring it to your attention if you didn't notice. Loving the final bits of this series coming together man!!

@katt8104

5 жыл бұрын

I thought I was seeing shit lmao

@LukeTheJoker

5 жыл бұрын

It seems to be that camera, it was doing it in another section too. May have been dropped at some point?

@j0nnyh34t7

5 жыл бұрын

I think it’s because they’re welding so they have electrical interference. But just a thought. 🤷‍♂️

5 жыл бұрын

Yeah, i paused the video to check any comments about this🤔

@mattb.2359

5 жыл бұрын

Or might have to deal with the light emitted by welding. Camera lenses can only take so much abuse.

Car went from looking 30% complete to straight 90%!! Took a big jump forward with concealing everything. Good job guys!!

Yo dude you thought about wrapping that exhaust up to stop heat coming through the floor??

He looks tired asf at the end

@BisforBuild

5 жыл бұрын

i was!

Fiberglass doesnt make a watertight seal with the metal so moisture will still get in.

Oh this project has grabbed my attention almost as much as the Aston.... Almost lol. I love the Aston

@michaelm6574

5 жыл бұрын

John Hurst still waiting for the difuser tho. Lol

I really enjoy the timelapses. If you every need too make a timelapse due time reasons don't worry too much about it, just do IT!

This thing is really starting to come together. Not trying to take away from what you are doing but eric is quite an asset to your channel and your builds, youre lucky to have him! Keep living the dream brother

That front shot of the car right after you started it up was awesome! Just seeing the fan spinning and hearing the car running is a look and sound of accomplishment. Well done so far!

Starting to look less like a bird nest of wires and more like a sema build👍

really wasn't sure any series could beat the lotus rebuild but this series has been hitting all the right spots

To be honest, at the beginning I wasn't sold on the project, but it really grew on me because of the high quality of work. It even exceeds the Evora as a signature build.

Chris, you're a lucky guy to have such talented and hard-working friends... all well deserved, I'm sure.

Amazing build. RESPECT!!

M240Z...it could be a drug name but it's just the best project car on KZread! It won't be perfect,but so close to the best you can do in a private garage! Keep going, buddy!

I've been waiting for this episode to see it with a floor. It makes it look much more complete.

Good luck, guys! You are kicking ass and I, for one, am loving this build!

“The metal is basically the scaffolding for everything” - b is for build 2018.

@BisforBuild

5 жыл бұрын

B is for Bodyfiller

Cardboard is still on the radiator so if it’s overheating that’s why

@maleficentcop2752

5 жыл бұрын

That is a spaical cardboard...gas permeable... LOL 👍

@Lysol_kb

5 жыл бұрын

he doesn't want to run the risk of damaging the fins on the radiator.

@harryballzack

5 жыл бұрын

I was thinking I saw cardboard still on there. LOL

@liammcmillan1209

5 жыл бұрын

he didnt have it running long enough for it to over heat well from what was shown in the vid atleast

@harryballzack

5 жыл бұрын

Liam McMillan that’s true. Was still funny to see that fan running for no reason. LOL

I'm so impressed with how this build is coming along, I've been watching the channel for a long while but this build I thought was a step too far.... Wow I was wrong! Props to you, absolutely well done to all of you for getting her to this point 👌🏻👏🏻

So hooked on this project. Been here since the beginning, as always good stuff Chris!

Why no bead rolling the long flat floor panels?

That was an epic time-lapse! PLEASE do more like that, you get more accomplished, and we get to see it done.

This has to be the single most amount of work done in a single day... episode! Holy fawk! Keep up the pace guys, your getting close to the home stretch!

Guys what you're doing with this build is incredible! A real inspiration, great work

By far the best ep thus far!!! Can’t wait to see the finished product!!!

Hey man, I’ve been following the gtr and the hurican builds and this is my first time watching the Z start to finish. I really appreciate you taking the time to film all of this stuff and put it online for us to enjoy. I love all of the detail and the hangups you include in the videos. Super inspiring.

Awesome work. It takes a heap of motivation at times for builds like these. Looking forward to watching this progress.

This channel will explode. Super stoked for you Chris

Don't forget if you have a trunk mounted fuel tank you should have a firewall between the trunk and the car to keep the any potential fire from the cell out of the main cabin.

So glad to see floors in! Loving this build

Excellent episode. Loved the extremely long time lapse. Really cool seeing this thing come together.

This is the first video of the series that I've 'liked' so far. I've enjoyed them all, though! As much as I like the explanations of why you're doing what - these time lapse videos of just lots of stuff getting done are really cool!

Absolutely killing it! You dudes are putting in work! It is very cool to have Oscar and Eric in the shop, yall make a great team!

You guys deserve a Nobel peace prize for wiring that thing without killing each other

One of my favorite episodes you've made Chris. Seeing the floorpan come together was awesome.

Good work guys. Having the floor done will make a massive difference. Looks better already.

WOW, you guys got a lot of work done! Hats off to the three of you

stunning work well done to all the team so far; the amount of work done each time is really impressive.

B for build is by far the best car video platform at youtube. he really does it by himself not like TJ who pays people and stike with the honour

Well Done! It's come a long way, props to you and the team that's got this beast this far. Going to be rad when finished.

Such a work of art! Keep up the good work boys! Can’t wait to see the final assembly!

Just catching up from the past week, SUPER EXCITED FOR YOU GUYS! YOU'RE GOING TO MAKE IT!

Highly recommend laying the paint down as quickly as possible so it has time to cure before transporting/driving it to SEMA.

This is going much better than I thought it was gonna be. Wasn't gonna leave any hate comments, and I'm glad I didn't. I was really sketched out by the previous frame rails you built. They just didn't look right at all. Glad it's coming together. And I see now why you moved the engine back away from the stock BMW mounts.

That's a colossal amount of work for one day. Great job, you guys!

Great job all, this will be so awesome when it's done! Keep it up y'all !

KEEP THAT HUSTLE UP!!!!!!!!!!!!!!!!! This car will be a show stopper, but, more importantly, it will be a trophy of what you and the guys can do. Massive props to everyone involved.

I thought you might be crazy when I saw all the work you did on the Evora, now after watching this build I know you are crazy. Amazing work man!!

The overhead view and time lapse welding was cool! Great work guys. 🤙

Eric’s a GOD lol . Great teamwork, glad to see this going exactly how you planned 🙏🏼

Great progress guys.

Chris I wish you good luck man! Thank you for the inspiration and positivity, I really want you to complete this amazing build!

Wow that's a lot of work that just got done, this is badass.

This is the video I've been waiting for couldnt wait to see the pans and boot welded in! Love yoir work and keep it up mate👊

I look forward to these episodes everyday. Keep up the great work! I can't wait to see it finished.

Love the progress guys. Keep it going.

Wow the floor really pulls together the whole build and looks great

Sorry would have responded sooner but actually watched the video. Love the transformation. It is looking so good.

Chris BAby im halfweay through the timelapse brother. THIS SHIT ROCKS! I love watching y'all chugg through that fab work. You are the real one.

I like this format of some explanation and then time lapse. We are all car guys and girls here, we know what you are doing. Great work!

Awesome work guys!

This video was amazing and I’m amazed you got so much done in this video. Well done with the floor, it look really cool.

Why not paint the top part of the frame before welding in the floor?? Will it not rust?

@anitagofradump2683

5 жыл бұрын

I was thinking that, and the floor panel above the frame

@danieljackson4422

5 жыл бұрын

Snap same thoughts.... although you cant see it rust so no problem right?

@MultiTerpen

5 жыл бұрын

Yes, I also hope that he will drill holes and paint on the inside of the frame and all the cavities.

@danieljackson4422

5 жыл бұрын

@@MultiTerpen nahh doesn't make for great viewing does it

Damn dudes, that some solid progress. Nice work!

You guys are getting there. A lot of progress on this one. Keep it up. Can’t wait to see it finished.

been watching this build since the beginning, awesome progress, really hope he goes all out in making this car sick. like show car quality not just a track car.

It’s so dope seeing it all come together.

Probably one of my favorite b is for build episodes right here

great looking real good, good work cant wait to see this thing complete keep it going !!!

Greatest, & most productive video yet!!! Keep up the great work Chris!!

Best car build channel! I’ve been watching for a while and your content just keeps getting better! Great job on everything.

This build is coming together so nicely

This is so awesome! You guys are killing it!

Awesome episode with some great progress. Keep it up Chris and Co!

Yes! I'm excited the floor panels are going on finally lol 🙌

Looks amazing, good job guys!

Seam seal would take forever, truck line the interior. Weather sealing and sound proofing in one!! Great build!!!

You guys are killing it. My favourite build ♡

Awesome build your still absolutely killing it