2020 mod E-TEC 140 test. Boat type: Ibiza 20 Touring. Water temperature 8*celcius 21p Evinrude steel propeller
Жүктеу.....
Пікірлер: 57
@newgeneration3496 Жыл бұрын
So sad that they’re gone, as I was repowering I got wind that they might be going under, I wanted a newer 2 stroke & they’re the only ones still doing them. Hands down the most appealing outboard looks wise to ever hit the market.
@promongo3 жыл бұрын
Excellent video
@MUSZAMEDAK2 жыл бұрын
I like this content,....perfect
@dsciarrino36632 жыл бұрын
The best money can by.
2 жыл бұрын
Great power
@poseidon5003 Жыл бұрын
That's impressive.
@marinoenergy44882 жыл бұрын
Great power, We hope Evinrude Outboards come back a gain with the best 4 stroke Engines..
@wetrpm2584
2 жыл бұрын
That would be great if they come back!
@nicolaimyrvoll1685
2 жыл бұрын
not with 4 stroke enignes
@justinlyonsPawPatrol
2 жыл бұрын
@@wetrpm2584 yes and seven marine
@cz32492 ай бұрын
I love my etec
@psi23k2 жыл бұрын
Nice 👌
@user-jp6jz8id7q Жыл бұрын
Кайф🤘
@stevecrawley54503 жыл бұрын
Love my G2. too bad they are gone. You did not reach your max rpm. Either trim up or get another prop with the right pitch. Your max rpm should be close to 6k I thought. At least it is on my 200 hp. Enjoy that G2
@trygvegabrielsen8120
3 жыл бұрын
why so important to reach 6000 RPM? when BRP says max HP is at 5000 RPM.
@stevecrawley5450
3 жыл бұрын
@@trygvegabrielsen8120 because if you make it to 6000 prm you have selected the the correct prop for your set up. If BRP says 5000 then fine
@ganerboss900
Жыл бұрын
Try to reach max hp rpm better, not the max rpm limit ,from my experience...
@ErnestoFavor763 жыл бұрын
Needs to go up 2 holes at least. Would stop the porpoising and you would be able to trim more without starting to porpoise. Would go 2 to 4 miles/h faster and give you +- 300 rpm more..... Before you start changing props get the engine height right. The ventilation plate should be out of the water at least on a fast cruise. Good luck 👍🏾
@wetrpm2584
3 жыл бұрын
tryed one hole up when I first installed the engine, a lot of cavitation and overall bad performance. after testing different heights this one was the best. I have over 80 engine hours now and I must say that I'm very satisfyed with the overall performance. I see a lot of comments here regarding the top rpm, and the staff at the shop where I bought the motor says the e-tec performs best if it can "run heavy". The speed is there, but at a lower rpm, I don't think I will get any more speed with changing prop, cuz I tryed :)
@ErnestoFavor76
3 жыл бұрын
@@wetrpm2584 If it works, it works, thank you for your reply. So many variables angle of the boat, kind of prop, etc..... All the best 👍🏼🤗
@hydrostream762 жыл бұрын
i would just get a transom lift and that would give you some set back like a see saw keep your center of gravity near the pad
@demetresichinava50882 ай бұрын
👍👍👍👍
@walidalasadi46573 ай бұрын
its the icon of the outboard but its very sad to stop it
@FABGRP3 жыл бұрын
4 stroke Evinrude G4 should be come in the near future.
@lyft92
3 жыл бұрын
Sad thing it won’t
@aaron-fauth
3 жыл бұрын
It won’t and it would be G3 not G4
@kylebuschfan3228
Жыл бұрын
Nah, keep it a 2strokes, the only reason why they disappear is the reputation of carby 2atroke while this evinrude was better than every other outboard
@user-yj3nz1tr7y2 жыл бұрын
HI, AND THE TRIM FOR ONE STOCK?AND THAT IT IS ENOUGH TO CLIMB AT SPEED?USUALLY THERE ARE THREE RODS?
@wetrpm2584
2 жыл бұрын
If i understand you correctly you are talking about the trim and tilt cylinders? There are two cylinders for trim and one for tilt. The single one are for tilting the motor all the way up.
@user-yj3nz1tr7y
2 жыл бұрын
@@wetrpm2584 So you have three cylinders on your engine? The video shows just one.
@wetrpm2584
2 жыл бұрын
@@user-yj3nz1tr7y there is just one :)
@djajello2982 жыл бұрын
Should have Bob's Jack p!ate, raise that motor, I have a Bob's 8" set back on a 150 G2 E tec On 21' 6" ft A Storm Bass Boat
@esasaarinen24232 жыл бұрын
it looks like you should raise the motor quite a bit
@groermunoz86262 жыл бұрын
Donde puedo comprar este motor
@wetrpm2584
2 жыл бұрын
aquí, en noruega, los distribuidores todavía venden los motores restantes. pero no se han fabricado más motores evinrude después de 2020.
@G0696GO2 жыл бұрын
Не понял, а выхлоп? Почему пузырей нет?
@wetrpm2584
2 жыл бұрын
At idle all the exhaust comes out over the waterline, just under where the water control flow comes out.
@edwinwong81963 жыл бұрын
You never got up to 5500 rpm WOT either raise your motor or a smaller pitch prop .
@bustedoff6038
2 жыл бұрын
its fine the rev limiter is 6000, but it could do with a lower pitch prop.
Пікірлер: 57
So sad that they’re gone, as I was repowering I got wind that they might be going under, I wanted a newer 2 stroke & they’re the only ones still doing them. Hands down the most appealing outboard looks wise to ever hit the market.
Excellent video
I like this content,....perfect
The best money can by.
Great power
That's impressive.
Great power, We hope Evinrude Outboards come back a gain with the best 4 stroke Engines..
@wetrpm2584
2 жыл бұрын
That would be great if they come back!
@nicolaimyrvoll1685
2 жыл бұрын
not with 4 stroke enignes
@justinlyonsPawPatrol
2 жыл бұрын
@@wetrpm2584 yes and seven marine
I love my etec
Nice 👌
Кайф🤘
Love my G2. too bad they are gone. You did not reach your max rpm. Either trim up or get another prop with the right pitch. Your max rpm should be close to 6k I thought. At least it is on my 200 hp. Enjoy that G2
@trygvegabrielsen8120
3 жыл бұрын
why so important to reach 6000 RPM? when BRP says max HP is at 5000 RPM.
@stevecrawley5450
3 жыл бұрын
@@trygvegabrielsen8120 because if you make it to 6000 prm you have selected the the correct prop for your set up. If BRP says 5000 then fine
@ganerboss900
Жыл бұрын
Try to reach max hp rpm better, not the max rpm limit ,from my experience...
Needs to go up 2 holes at least. Would stop the porpoising and you would be able to trim more without starting to porpoise. Would go 2 to 4 miles/h faster and give you +- 300 rpm more..... Before you start changing props get the engine height right. The ventilation plate should be out of the water at least on a fast cruise. Good luck 👍🏾
@wetrpm2584
3 жыл бұрын
tryed one hole up when I first installed the engine, a lot of cavitation and overall bad performance. after testing different heights this one was the best. I have over 80 engine hours now and I must say that I'm very satisfyed with the overall performance. I see a lot of comments here regarding the top rpm, and the staff at the shop where I bought the motor says the e-tec performs best if it can "run heavy". The speed is there, but at a lower rpm, I don't think I will get any more speed with changing prop, cuz I tryed :)
@ErnestoFavor76
3 жыл бұрын
@@wetrpm2584 If it works, it works, thank you for your reply. So many variables angle of the boat, kind of prop, etc..... All the best 👍🏼🤗
i would just get a transom lift and that would give you some set back like a see saw keep your center of gravity near the pad
👍👍👍👍
its the icon of the outboard but its very sad to stop it
4 stroke Evinrude G4 should be come in the near future.
@lyft92
3 жыл бұрын
Sad thing it won’t
@aaron-fauth
3 жыл бұрын
It won’t and it would be G3 not G4
@kylebuschfan3228
Жыл бұрын
Nah, keep it a 2strokes, the only reason why they disappear is the reputation of carby 2atroke while this evinrude was better than every other outboard
HI, AND THE TRIM FOR ONE STOCK?AND THAT IT IS ENOUGH TO CLIMB AT SPEED?USUALLY THERE ARE THREE RODS?
@wetrpm2584
2 жыл бұрын
If i understand you correctly you are talking about the trim and tilt cylinders? There are two cylinders for trim and one for tilt. The single one are for tilting the motor all the way up.
@user-yj3nz1tr7y
2 жыл бұрын
@@wetrpm2584 So you have three cylinders on your engine? The video shows just one.
@wetrpm2584
2 жыл бұрын
@@user-yj3nz1tr7y there is just one :)
Should have Bob's Jack p!ate, raise that motor, I have a Bob's 8" set back on a 150 G2 E tec On 21' 6" ft A Storm Bass Boat
it looks like you should raise the motor quite a bit
Donde puedo comprar este motor
@wetrpm2584
2 жыл бұрын
aquí, en noruega, los distribuidores todavía venden los motores restantes. pero no se han fabricado más motores evinrude después de 2020.
Не понял, а выхлоп? Почему пузырей нет?
@wetrpm2584
2 жыл бұрын
At idle all the exhaust comes out over the waterline, just under where the water control flow comes out.
You never got up to 5500 rpm WOT either raise your motor or a smaller pitch prop .
@bustedoff6038
2 жыл бұрын
its fine the rev limiter is 6000, but it could do with a lower pitch prop.
26 knots
HOLA DIOS EVINRUDE BRP???
The motor seems way low too me..
G2 er kule maskiner.
Damn that trim is slow
u need 19" prop not 21"
Мая Ямаха 85 больше 60 не тянет
😔
max speed ?
@wetrpm2584
3 жыл бұрын
41kn
@justinlyonsPawPatrol
2 жыл бұрын
he did not use MPH mode
Как не приятно бортом черкнул
motor is waaay too low