Nice video! We are so fortunate to have talented mechanics like you sharing their knowledge and skills. Everyone with an automobile needs to see how much work and knowledge is required to repair a modern vehicle. Thanks for sharing!
@markbevilacqua3415 Жыл бұрын
Awesome video! Very detailed !
@darrenlavigne68492 жыл бұрын
Good vid Glad to see you mixing up the content Keep er up 👍
@rudeskii7827 Жыл бұрын
So helpful, quick question.. So i have yo rebuild or replace my transmission, those are my two options.. so obviously my 10r8 has to come out.. Do you know if i have to retune it? I was told by someome that once i pull it out the trans that the tcm resets to factory.. Personally i dont think it does because the battery will be unplugged and even that wouldnt reset my ecm.. any thought or knowledge?
@johnallen19012 жыл бұрын
Those top bellhousing bolts must be lots of fun on the install.
@expressautotransmissiondav4207
2 жыл бұрын
Bahahhaha yes they can be a lot of fun for sure
@paulhastings7480 Жыл бұрын
Is there any reprogramming that needs done when replacing a 6r80 transmission? I keep getting told they required programing in a new trans.
@100mphClub2 жыл бұрын
My transmission is out! Woohoo! Another note: 6th gear was slipping as well as the clunky shifting in the lower gears. It slipped after a 10.70 pass at 128mph.
@expressautotransmissiondav4207
2 жыл бұрын
She's not gonna do that now
@korky122 Жыл бұрын
my GFs 2019 4 cylinder mustang trans just went. how much and how long this usually cost to get repaired? dam car has like 35k miles on it.
@garyrichards4072 жыл бұрын
Ford did a few things to make removal easier like the rubber plug , flanged drive shaft and not to have to remove the exhaust system to get the tranny out.
@expressautotransmissiondav4207
2 жыл бұрын
It definitely makes it easier
@romanperehrestenkomyway31403 ай бұрын
Thx
@yoganlates77752 жыл бұрын
I'll be taking my 10r80 out here real soon to send off to get clutches, thermal bypass, and "zero flex f apply plates." I really appreciate the video! My only problem is going to be jacking the trans, and I definitely don't want to bust the plastic pan. Any advice for doing this on the ground without a lift?
@expressautotransmissiondav4207
2 жыл бұрын
Buy a transmission jack is the biggest thing harbor freight has a reasonable priced one that would work just fine
@TboneSTEAK111
Жыл бұрын
If you live in cold climate don't do the thermal bypass. My trans never gets over 110F if it's under 50 degrees after 40 mins of driving. The fluid shouldn't be 230F, but it definitely shouldn't be barely above "Warm" either, it's almost just as bad.
@jake_mf_lowe9525 Жыл бұрын
My block where those ears connect to the bell housing cracked on both brackets... So im waiting for ford to tell me im screwed.
@reist1982 Жыл бұрын
Hey. Question for you. Do I need to reprogram anything if I replacing my faulty transmission with same model one? Thank you in advance.
@expressautotransmissiondav4207
Жыл бұрын
I say yes.
@MHolt35732 жыл бұрын
How did you go about getting your own shop. I have been wanting to open my own place.
@expressautotransmissiondav4207
2 жыл бұрын
It all kinda happened really fast I made the decision one day working for a local transmission shop. Within a week I had a place found and shook hands on the building im in. If you want to do it jump in feet first is my way of thinking. I was scared and will never deny that but I was confident in what I could do. It's been full of ups and downs that I never truly expected, but I wouldn't feel like myself doing anything else. I hope you take the leap ambition will drive you a long way. Being honest enough to ask to learn is a great building block for a great transmission mechanic. You can do it
@MHolt3573
2 жыл бұрын
@@expressautotransmissiondav4207I work at a fleet shop now as a diesel mechanic & I work with my wife's uncle who was a transmission/bumper to bumper mechanic. My boss passed away at the fleet shop so they put me in charge. I really learned alot about the "other" side to a shop (paperwork, ordering parts, lining up jobs, ect) I'm at the scary part now of taking the leap to do mine own thing.
@expressautotransmissiondav4207
2 жыл бұрын
All I can say is take the leap.
@paulhastings7480 Жыл бұрын
Does the 6r80 come out and bolt up the same?
@expressautotransmissiondav4207
Жыл бұрын
Very similar
@paulhastings7480
Жыл бұрын
Awesome. mine lost 3-4 so I either need to try a rebuild or just remove and replace the trans. Im Hoping my long tubes won't be a pain.
Пікірлер: 26
Nice video! We are so fortunate to have talented mechanics like you sharing their knowledge and skills. Everyone with an automobile needs to see how much work and knowledge is required to repair a modern vehicle. Thanks for sharing!
Awesome video! Very detailed !
Good vid Glad to see you mixing up the content Keep er up 👍
So helpful, quick question.. So i have yo rebuild or replace my transmission, those are my two options.. so obviously my 10r8 has to come out.. Do you know if i have to retune it? I was told by someome that once i pull it out the trans that the tcm resets to factory.. Personally i dont think it does because the battery will be unplugged and even that wouldnt reset my ecm.. any thought or knowledge?
Those top bellhousing bolts must be lots of fun on the install.
@expressautotransmissiondav4207
2 жыл бұрын
Bahahhaha yes they can be a lot of fun for sure
Is there any reprogramming that needs done when replacing a 6r80 transmission? I keep getting told they required programing in a new trans.
My transmission is out! Woohoo! Another note: 6th gear was slipping as well as the clunky shifting in the lower gears. It slipped after a 10.70 pass at 128mph.
@expressautotransmissiondav4207
2 жыл бұрын
She's not gonna do that now
my GFs 2019 4 cylinder mustang trans just went. how much and how long this usually cost to get repaired? dam car has like 35k miles on it.
Ford did a few things to make removal easier like the rubber plug , flanged drive shaft and not to have to remove the exhaust system to get the tranny out.
@expressautotransmissiondav4207
2 жыл бұрын
It definitely makes it easier
Thx
I'll be taking my 10r80 out here real soon to send off to get clutches, thermal bypass, and "zero flex f apply plates." I really appreciate the video! My only problem is going to be jacking the trans, and I definitely don't want to bust the plastic pan. Any advice for doing this on the ground without a lift?
@expressautotransmissiondav4207
2 жыл бұрын
Buy a transmission jack is the biggest thing harbor freight has a reasonable priced one that would work just fine
@TboneSTEAK111
Жыл бұрын
If you live in cold climate don't do the thermal bypass. My trans never gets over 110F if it's under 50 degrees after 40 mins of driving. The fluid shouldn't be 230F, but it definitely shouldn't be barely above "Warm" either, it's almost just as bad.
My block where those ears connect to the bell housing cracked on both brackets... So im waiting for ford to tell me im screwed.
Hey. Question for you. Do I need to reprogram anything if I replacing my faulty transmission with same model one? Thank you in advance.
@expressautotransmissiondav4207
Жыл бұрын
I say yes.
How did you go about getting your own shop. I have been wanting to open my own place.
@expressautotransmissiondav4207
2 жыл бұрын
It all kinda happened really fast I made the decision one day working for a local transmission shop. Within a week I had a place found and shook hands on the building im in. If you want to do it jump in feet first is my way of thinking. I was scared and will never deny that but I was confident in what I could do. It's been full of ups and downs that I never truly expected, but I wouldn't feel like myself doing anything else. I hope you take the leap ambition will drive you a long way. Being honest enough to ask to learn is a great building block for a great transmission mechanic. You can do it
@MHolt3573
2 жыл бұрын
@@expressautotransmissiondav4207I work at a fleet shop now as a diesel mechanic & I work with my wife's uncle who was a transmission/bumper to bumper mechanic. My boss passed away at the fleet shop so they put me in charge. I really learned alot about the "other" side to a shop (paperwork, ordering parts, lining up jobs, ect) I'm at the scary part now of taking the leap to do mine own thing.
@expressautotransmissiondav4207
2 жыл бұрын
All I can say is take the leap.
Does the 6r80 come out and bolt up the same?
@expressautotransmissiondav4207
Жыл бұрын
Very similar
@paulhastings7480
Жыл бұрын
Awesome. mine lost 3-4 so I either need to try a rebuild or just remove and replace the trans. Im Hoping my long tubes won't be a pain.