2016-2019 Honda Pilot OEM Trailer Hitch Install and Wiring Harness
This video shows you how to install the factory OEM accessory trailer hitch to a 2016, 2017, 2018, and 2019 Honda Pilot. This particular car is a 2018 Honda Pilot AWD base model. I show you all the steps it takes to be able to completely put the trailer hitch on your vehicle. I have also made a separate video for the trailer hitch wiring.
Honda Trailer Hitch(Amazon): amzn.to/3y3ZaYi
Honda Trailer Hitch(eBay): ebay.us/mIKytc
Honda Wiring harness(Amazon): amzn.to/3oe92uc
Honda Wiring harness(eBay): ebay.us/mZ18Ek
Honda Transmission Cooler Kit: amzn.to/3xIybDp
Honda hitch plug: amzn.to/33UZM4x (If needed, comes in above kit)
4 blade flat wiring harness adapter: amzn.to/3j6zsx6
Curt Adjustable Ball Mount: amzn.to/30EWMuL
14MM X 1.5 Thread Tap: amzn.to/3qOCWKT
HORUSDY 48-Pieces Thread Chaser Set: amzn.to/3NmAl2q
Wiring harness video: • 2018 Honda Pilot Trail...
Transmission cooler install video: • 2016-2020 Honda Pilot ...
Filmed with:
GoPro Hero 9: amzn.to/3fhXgdQ
Neewer 660 Lighting: amzn.to/3bougA3
GoPro Mount: amzn.to/3ocP0Qr
Vanguard Tripod: amzn.to/3hldN3o
Amazon Links are associate links and I will receive a small portion of any sales
Пікірлер: 90
Would everyone like me to make a how to video for the Honda add on transmission cooler? Let me know!!
@YusiYL
2 жыл бұрын
Yes Yes
@cm1133
7 ай бұрын
Yed
Thank you for the videos! They worked great! I reviewed them a few times and installed the wiring harness then the hitch today. It went smoothly and I ran into rust in the hitch bolt holes as well here in Maryland. Thanks for making the time to share this. You saved me hundreds $$$ of not having to pay someone to do it and I learned there are still some things we can do to work on cars these days!! Thanks again!!
@chuckger1625
Ай бұрын
Are these 14mm or 18 mm bolts - because he lists a 14mm tap in his comments. Did you use a tap or just the bolts to free the rust?
Добрый день! У меня Пилот 2020 года выпуска. Огромная благодарность за такой понятный и чёткий обзор по установке проводки и фаркопа на Хонду Пилот, просто суппер!!! Я не знаю английского языка но всё что было показано понятно и поучительно!!! Ещё раз огромная благодарность молодому человеку!!!
Thanks for the video! Will be installing Oem hitch and harness this weekend.
@streetriderscustoms
11 күн бұрын
Hopefully this video helps you get the project done easy!
@KantusKid
11 күн бұрын
Helped tremendously. Removed the rear quarter panel and it made installation a whole lot easier. Thanks a bunch! I can finally tow my kayaks now!
Extremely helpful! Saved me loads of time and frustration.
Thank you! Hope this video helps future pilot owners
@streetriderscustoms
11 ай бұрын
Thanks for watching!
Thanks so much for this set of videos! The only thing that tripped me up a little bit was that mine is a Touring model with a rear 12V outlet and I needed to remember to unhook that to remove the panel. Also - it's easy to bend the contacts on the outlet as you're moving the panel around, so be careful.
@streetriderscustoms
3 жыл бұрын
Thanks for watching! I am glad they helped you out, and as of course watch out for those extra connections!
Very helpful I finished my Honda Pilot 2016 successfully. Wire and hitches install
@streetriderscustoms
Жыл бұрын
Awesome! I am glad the video helped you install yours!
Great video totally helped me out. You saved me and my pocket book alot of headaches.
@streetriderscustoms
2 жыл бұрын
I'm glad that the video could help you through the install! Thanks for watching!
I put on the factory hitch on my 2022 Honda Pilot. I used a wire brush on the bolt holes similar to the that used with a battery brush. I blew out the bolt hole with compressed air then used the proper metric tap with WD40 to chase out the rest of the rust in the threads. I used a ratcheting box wrench to turn the tap which worked great.
@streetriderscustoms
Жыл бұрын
It helps a lot getting those threads cleaned out before installing. Glad you could get yours installed easily
Awesome Video!!! Thank you for the detailed steps. I’ll be doing my 2021 soon, Wish you had the power lift adapter 😂👍🏻
@streetriderscustoms
3 жыл бұрын
I hope it's clear enough to follow when you start your project! Thanks for watching
Thanks for both videos
@streetriderscustoms
2 жыл бұрын
Thanks for watching! I hope they help out!
Well done and explained., thanks! Had some doubts on clips but you cleared that and the visuals of course, always tell the tale. Best wishes., God bless you! 🤜🏻🤛🏻
@streetriderscustoms
Жыл бұрын
Glad that the video could help! Its not as hard as it looks, especially with some good directions!
Great video, and thanks for including all the links to purchase the parts.
@streetriderscustoms
3 жыл бұрын
Glad you were able to follow along. Good luck with the install!
@jimihiggins5580
3 жыл бұрын
@@streetriderscustoms where are these links located?
@jimihiggins5580
3 жыл бұрын
Never mind. Found them.
@streetriderscustoms
3 жыл бұрын
@@jimihiggins5580 in the description! Thanks man
Thanks again for the video!! Installed the hitch this weekend. Man...you were NOT kidding about those bolt holes! Of the 2hrs it took for the installation, 1:45 of that was getting those bolt holes cleaned!! LOL. I think I STILL smell like PBBlaster. Not only did I nuke the bolt holes with PBBlaster...I also grabbed some 1/2" wire 'tube brushes', attached it to my drill and was able to get the threads cleaned out pretty readily. Wish Honda could have spent the extra $0.15 and put some plastic plugs over those holes! :)
@streetriderscustoms
2 жыл бұрын
So true! I ran into so much trouble getting those bolt holes cleared out. Such a simple project but yet there's always an issue! Glad to hear you got it done!
OEM transmission cooler install would be great!
@streetriderscustoms
3 жыл бұрын
I think I will be doing that this summer!
I need see you other video for the Wiring Harness install Thanks
@streetriderscustoms
2 жыл бұрын
Here you go kzread.info/dash/bejne/a6Z3lNWNlNadeto.html
This was great! Thank you!
@streetriderscustoms
3 жыл бұрын
Glad I could help you get it done!
@The1FUNBOX
3 жыл бұрын
@@streetriderscustoms I'm having the same issue with rust. Luckily I was able to get 2x2 bolted the last ones won't budge spent a hour trying to get them threaded need some WD40.
Thanks and a video of how to connect the cables to the lights.
@streetriderscustoms
2 жыл бұрын
Using the factory wiring harness you do not need to plug anything into the lights
Need 14 MM X 1.50 Century metric tap to clean rust out of trailer hitch threaded inserts.
@abimatt8746
2 жыл бұрын
What tool did you use the tap ? Is there a particular wrench or
@chuckger1625
Ай бұрын
Are these 14mm or 18 mm bolts - because he lists a 14mm tap in his comments. Did you use a tap yourself?
If you are putting a hitch on a Pilot that's several years old, buy a 14x1.5 thread tap to chase the threaded holes in the frame to clean the rust out. That is a fine pitch thread that, when combined with a bit of surface rust, is just begging to be cross-threaded.
@streetriderscustoms
Жыл бұрын
I thought I had a link in the description all ready but I just added a link now where people can buy one from Amazon. Comes in very handy when doing this job
@desmondyazzie2437
Жыл бұрын
That’s good info. I cannot get those bolts in hope that works.
The only drawbacks to living in states that get snow and ice the road salt does so much damage to the undercarriage all that rust looks gnarly.
@streetriderscustoms
2 жыл бұрын
That is the one and only reason I hate living in New England. It's hard finding a good used car that isn't rusted too much
Great video, was there a torque spec for the 6 bolts? Thanks!
@streetriderscustoms
4 ай бұрын
The torque spec for the bolts are 95nm or 70 lb ft
Hey if you don’t mind. Can you tell me why do some people use 3 fuses under the hood like 2 20 and one 30 I saw your video and you had only 2 ?
@streetriderscustoms
3 жыл бұрын
Im not 100% sure why, but they do give you a brake controller hookup which I did not install. There could be an extra fuse that went with that. I know that the 2 I put in is what you need for the wiring I installed
For final bolt tightening did you use Torque Wrench with specific ft-lb #?
@streetriderscustoms
3 жыл бұрын
Honestly I did not, but I have checked and retightened them, and will do so periodically after towing the camper
@magmavr6
2 жыл бұрын
I just completed this today. Torqued at 63ft-lb or about 85N-m.
@streetriderscustoms
2 жыл бұрын
Thanks for the numbers!
Did you have any problem with the trunk open assist? Opening the trunk with you foot.
@streetriderscustoms
3 жыл бұрын
This Honda is not equipped with that option, so I can't answer for you. I am sure that it would still work but not 100%
how was it to lift into place and get the bolts started solo? did you use something to prop the other side? I don't have anyone to help or anything to hold the other side up
@streetriderscustoms
2 жыл бұрын
It is not too bad. I would make sure the bolts go all the way up and chase the threads first with no rust in there. Then you can lift it up and balance the other side with your knees and get the bolts started. As long as the bolts go in easily you should be able to do it
Hello, I need if it is possible for you to tell me where you bought this kit to buy the same one please, my car is the same color Thank you
@streetriderscustoms
2 жыл бұрын
If you go to the description of the video I have the links to Amazon where you can buy from them
Is there a way to add the wiring after the hitch had already been installed? Mine already has. The oem hitch but no light powering.
@streetriderscustoms
2 жыл бұрын
Of course. It's a separate harness. I have a video on installing that also
@joel96763
Жыл бұрын
Thanks for the video. I was wondering the same thing. I ordered the hitch and will order the wiring harness much later. I'm assuming I can just leave the plug cut off intact for now? Will I have to loosen the hitch bolts to install the harness later?
How exactly are you cleaning out the rust? With wd40? And by tightening and loosening? Im about to do my 2021
@streetriderscustoms
3 жыл бұрын
Yes, spray it good with pb blaster or wd 40 and just work the bolt in a little at a time and then back out.
@pshawhudson
3 жыл бұрын
Great Thanks! Appreciate the video.
You didn't show how you did this yourself. How did you get the heavy hitch assembly up to screw it in?
@streetriderscustoms
11 күн бұрын
I lifted it up with my hands and basically held the other side up with my foot. Once you get a bolt on each side started it will not fall down. You could use a floor jack on one side also to help
Hey If you don't mind me asking, the exact bolt size. I want buy extra to clean the rust similar to you. I live in north as well, and just checked it is rusty. sprayed some PB blaster but wanted clean with spare bolt. I just ordered the hitch have not received it yet to go look for it. Thanks in advance.
@streetriderscustoms
3 жыл бұрын
From a couple website it looks like the bolt size is M14 x 1.50, and whatever length you want, the factory bolts are 40mm. It's a great idea to clean those up before hand. Mine were so bad it took forever to get them all the way in.
@rikram33
3 жыл бұрын
@@streetriderscustoms Thanks for the prompt response. They look pretty bad on mine. I may have to spray some more PB blaster. Now will look for those bolts.
@streetriderscustoms
3 жыл бұрын
Good luck! Just remember to take your time and go slow, one of those break off in the frame and its game over!
@stephendudek8806
3 жыл бұрын
You can buy a 14mm x 1.5mm pitch tap on Amazon for $12 and use that to chase (clean up) the threads. I have a 2018 pilot and live in Chicago so I had 3 years of rust on these threaded holes when I went to put the hitch on. After trying to clean the threads I was able to get all the bolts started, but no where near all the way in. Used the tap and viola - no problem with bolts. Hindsight - I should have purchased the tap to start with given the snow and salt where I live. www.amazon.com/dp/B07VX8DX7Q?ref=ppx_pop_mob_ap_share
@rikram33
3 жыл бұрын
@@stephendudek8806 Thanks so much.
Hi, does your honda hitch take a 2 inch receiver bar??
@streetriderscustoms
5 ай бұрын
Yes this hitch is a 2" receiver
@brandonalbright125
5 ай бұрын
@streetriderscustoms thank you. I just ordered one.
I see yours is kinda offset to the left in the bumper cutouts mine is too. I'm kind of a perfectionist so i wasn't pleased but oh well🤷♂️
@streetriderscustoms
3 жыл бұрын
Ya it is off centered. It does actually annoy me but there's just no way to make it fit any better. Thanks a lot Honda!!
I just picked up the hitch for $408...from Honda. LGB
@streetriderscustoms
2 жыл бұрын
You should return it and buy from the link in the description and save money
Just remember if you don’t have a Honda factory ATF cooler you still only tow 3,500lbs/350TGW. VS 5,000lbs/500TGW with ATF cooler.
@streetriderscustoms
3 жыл бұрын
Very true, these aren't to beasts. I'm not sure if I will add one or not, our camper is around 1500lbs
@jppilotadventurez5251
3 жыл бұрын
@@streetriderscustoms I would, these cars and transmission aren’t really built in mind for towing, yeah we "CAN". I just added mine yesterday. Taking it to dealer to make sure transmission fluid is at the proper level.
Every time I click the link for the parts the price keeps going up. REALLY WTF! great video but the nickel and dime algorithm crap is annoying.
@streetriderscustoms
Жыл бұрын
Unfortunately I have no control over that! I just put the links to Amazon in there and those prices are set by whoever is selling them. I have noticed that when I first uploaded the video the prices were much lower than they are now