2012-2017 Toyota Camry How To Replace the Front Brake Pads and Rotors
Жүктеу.....
Пікірлер: 43
@BurtBowers2 күн бұрын
Well done video buddy, glad you shown included first step of doing brakes is opening the Master cylinder cap letting it lay ontop of the master cylinder reservoir, i seen lot videos out here on other channels they never mention or show doing this whichbis very important doing this, thanks for the posting👍
@scottsmith8909 Жыл бұрын
Good video, going to put front pads on my 2017 Camry that we bought new. I’ve put lots of brake pads on but I wanted to maybe learn some tricks on the Camry. Thanks!
@saulreynoso43713 жыл бұрын
Great video. It's the first time I am going to do my brakes on my camry, but I have done plenty of brake jobs. The only thing I would suggest is putting anti seize where the rotor comes in contact with the wheel bearing and the rim. Makes it a lot easier to remove the rotor next time. Great job though.
@OEMEangg
3 жыл бұрын
thanks for the tip
@Loki2Mira Жыл бұрын
Great video thanks. Just did our brakes. Was going to do rotors also but I couldn’t get them off even hitting with a hammer. Guess their rusted on. I will do them later on and just soak them with some blaster.
@ethanfarkas4190
Жыл бұрын
was your e-brake on?
@BetterTrue3 жыл бұрын
Neat video ... perfectly shot clear and simple explanation.
@OEMEangg
3 жыл бұрын
thanks.
@littlerascals65292 жыл бұрын
Great video,thank you!👍
@SheikShak Жыл бұрын
Thanks….will do mine…..
@giurbitser Жыл бұрын
Thank you excelent
@Ddcash3002 жыл бұрын
Great video.
@josepgutierrez223 жыл бұрын
A 2016 Toyota Avalon break change should be pretty similar to this right?
@OEMEangg
3 жыл бұрын
Yeah, most brake jobs are similar.
@poohmaster543 жыл бұрын
Could I use the brake and caliper grease in place of the silicone paste? I'm also wondering if I can just loosen the bleeder screws as opposed to using the C-clamp to squeeze the pads?
@OEMEangg
3 жыл бұрын
I'm not sure if you can use the caliper grease in place of silicone paste. Yes, you can open the bleeder instead of compressing the piston. Just make sure air is not going to enter the brake system by using the "bottle with a tube filled with brake fluid".
@riasat0013 жыл бұрын
No rust
@hcag22 Жыл бұрын
Do you have to perform a brake bedding-in procedure with these OEM pads/rotors?
@OEMEangg
Жыл бұрын
No need for bedding. It is recommend to drive and brake smoothly for the first 100 mile or so. Avoid sudden stops. (BUT of course if it is an emergency, by all means, hit the brakes.)
@Loki2Mira Жыл бұрын
Just have another question? I was able to change the brake but I guess the rotors had kinda rusted. I tried hitting the back of them with a hammer and they didn’t move at all. They don’t have any of the set screws in the front. I’d there s trick or something I am missing
@OEMEangg
Жыл бұрын
I have a video for brake job on a Toyota Highlander. In it, I show how to take off a rusted rotor. You will need to get two bolts. You can start the video around 3 minutes in. kzread.info/dash/bejne/qauf15Zqf6y7laQ.html
@luisgastelum8307 Жыл бұрын
Why would you skip when you put the pads on
@mattt96342 жыл бұрын
5 in c clamp?
@g2nut433 жыл бұрын
Where did u get the nice flip flops from ?
@OEMEangg
3 жыл бұрын
LOL... That guy is not me.
@SeorgeGoros
3 жыл бұрын
This is by far the best brake pad installation vid I have seen. Very informative and clear
@OEMEangg
3 жыл бұрын
@@SeorgeGoros Thanks for the comment. Some have told me I give too much info.
@SeorgeGoros
3 жыл бұрын
@@OEMEangg whoever complains about too much info when it comes to working on a car is a fool who shouldn’t be taken serious
@OEMEangg
3 жыл бұрын
@@SeorgeGoros Thanks for the comment. I really appreciate it.
@B-S19992 жыл бұрын
Is it the same as 2017 Camry hybrid
@OEMEangg
2 жыл бұрын
I'm not 100% sure but I believe it is the same.
@riddit_stories972 жыл бұрын
What is the name of the first tool you are using in squeezing the caliper
@riddit_stories97
2 жыл бұрын
And also where I can get it thank you
@OEMEangg
2 жыл бұрын
@@riddit_stories97 Some people call it a caliper compression tool or a disc brake pad spreader. You can buy it online or any auto parts store. Below my video is the description. Click on “SHOW MORE”. I list some of the product and tools I use.
@Blank_PK
Жыл бұрын
He’s asking about the c clamp, I know this is old but for anybody in the future coming across this it’s a c clamp
@abrahamromero98783 жыл бұрын
Where do you bought the brake rotors
@OEMEangg
3 жыл бұрын
You can buy them from Autozone. They also sell them at O'Reilly Auto Parts or Pepboys.
@mikehand2668
2 жыл бұрын
I use only Toyota OEM only
@colochona812 жыл бұрын
Don’t see how take out rotors !! 🙄
@OEMEangg
2 жыл бұрын
At around 3:18, you take off the 2 bolts holding the caliper bracket. Now, there is nothing holding the rotor. You can just tap out the rotor. At 3:48, I point to where I tap out the rotor. Sorry about that. I should have recorded that part also.
Пікірлер: 43
Well done video buddy, glad you shown included first step of doing brakes is opening the Master cylinder cap letting it lay ontop of the master cylinder reservoir, i seen lot videos out here on other channels they never mention or show doing this whichbis very important doing this, thanks for the posting👍
Good video, going to put front pads on my 2017 Camry that we bought new. I’ve put lots of brake pads on but I wanted to maybe learn some tricks on the Camry. Thanks!
Great video. It's the first time I am going to do my brakes on my camry, but I have done plenty of brake jobs. The only thing I would suggest is putting anti seize where the rotor comes in contact with the wheel bearing and the rim. Makes it a lot easier to remove the rotor next time. Great job though.
@OEMEangg
3 жыл бұрын
thanks for the tip
Great video thanks. Just did our brakes. Was going to do rotors also but I couldn’t get them off even hitting with a hammer. Guess their rusted on. I will do them later on and just soak them with some blaster.
@ethanfarkas4190
Жыл бұрын
was your e-brake on?
Neat video ... perfectly shot clear and simple explanation.
@OEMEangg
3 жыл бұрын
thanks.
Great video,thank you!👍
Thanks….will do mine…..
Thank you excelent
Great video.
A 2016 Toyota Avalon break change should be pretty similar to this right?
@OEMEangg
3 жыл бұрын
Yeah, most brake jobs are similar.
Could I use the brake and caliper grease in place of the silicone paste? I'm also wondering if I can just loosen the bleeder screws as opposed to using the C-clamp to squeeze the pads?
@OEMEangg
3 жыл бұрын
I'm not sure if you can use the caliper grease in place of silicone paste. Yes, you can open the bleeder instead of compressing the piston. Just make sure air is not going to enter the brake system by using the "bottle with a tube filled with brake fluid".
No rust
Do you have to perform a brake bedding-in procedure with these OEM pads/rotors?
@OEMEangg
Жыл бұрын
No need for bedding. It is recommend to drive and brake smoothly for the first 100 mile or so. Avoid sudden stops. (BUT of course if it is an emergency, by all means, hit the brakes.)
Just have another question? I was able to change the brake but I guess the rotors had kinda rusted. I tried hitting the back of them with a hammer and they didn’t move at all. They don’t have any of the set screws in the front. I’d there s trick or something I am missing
@OEMEangg
Жыл бұрын
I have a video for brake job on a Toyota Highlander. In it, I show how to take off a rusted rotor. You will need to get two bolts. You can start the video around 3 minutes in. kzread.info/dash/bejne/qauf15Zqf6y7laQ.html
Why would you skip when you put the pads on
5 in c clamp?
Where did u get the nice flip flops from ?
@OEMEangg
3 жыл бұрын
LOL... That guy is not me.
@SeorgeGoros
3 жыл бұрын
This is by far the best brake pad installation vid I have seen. Very informative and clear
@OEMEangg
3 жыл бұрын
@@SeorgeGoros Thanks for the comment. Some have told me I give too much info.
@SeorgeGoros
3 жыл бұрын
@@OEMEangg whoever complains about too much info when it comes to working on a car is a fool who shouldn’t be taken serious
@OEMEangg
3 жыл бұрын
@@SeorgeGoros Thanks for the comment. I really appreciate it.
Is it the same as 2017 Camry hybrid
@OEMEangg
2 жыл бұрын
I'm not 100% sure but I believe it is the same.
What is the name of the first tool you are using in squeezing the caliper
@riddit_stories97
2 жыл бұрын
And also where I can get it thank you
@OEMEangg
2 жыл бұрын
@@riddit_stories97 Some people call it a caliper compression tool or a disc brake pad spreader. You can buy it online or any auto parts store. Below my video is the description. Click on “SHOW MORE”. I list some of the product and tools I use.
@Blank_PK
Жыл бұрын
He’s asking about the c clamp, I know this is old but for anybody in the future coming across this it’s a c clamp
Where do you bought the brake rotors
@OEMEangg
3 жыл бұрын
You can buy them from Autozone. They also sell them at O'Reilly Auto Parts or Pepboys.
@mikehand2668
2 жыл бұрын
I use only Toyota OEM only
Don’t see how take out rotors !! 🙄
@OEMEangg
2 жыл бұрын
At around 3:18, you take off the 2 bolts holding the caliper bracket. Now, there is nothing holding the rotor. You can just tap out the rotor. At 3:48, I point to where I tap out the rotor. Sorry about that. I should have recorded that part also.
Brake jobs and flip flops - what a oxymoron 🙄👎