2011 Honda Pilot Rear Brake Pad Replacement
Автокөліктер мен көлік құралдары
amzn.to/3CPe2yh - Versachem 26080 Synthetic Caliper Grease
amzn.to/3FEVcJm - GEARWRENCH 3/8" Drive Micrometer Torque Wrench 10-100 ft/lbs. - 85062
amzn.to/3MSxspe - VESSEL MEGADORA IMPACTA Impact Driven Screwdriver +3x150 (6") No.980 980P3150
amzn.to/3TJIY8u - Max Brakes Premium OE Rotors with Carbon Ceramic Pads KT093942
amzn.to/3DsLATf - Power Stop 17-1281, Z17 Rear Ceramic Brake Pads with Hardware
amzn.to/3AyXq9B - Mission Automotive Brake Caliper Hooks/Brake Caliper Hangers (Set of 2)
amzn.to/3MRVRLv - 8-Pack of Rotor Screws for Brake Discs - Universal Fit for Honda, Acura, Hyundai and Kia Models - Stainless Steel Retaining Screws - By Mission Automotive
amzn.to/3ExJ3Ii - Milwaukee M12 FUEL 3/8" High Speed Cordless Ratchet
amzn.to/3TGT1Lz - Permatex 24200 6 ml Blue Medium Strength Threadlocker
amzn.to/2ZyyHl7 - Brake Cleaner
amzn.to/3sKJB6U - Milwaukee 2767-20 M18 FUEL High Torque 1/2" Impact Wrench with Friction Ring
amzn.to/3VQIhfu - 1/2" Drive Wheel Protector Impact Socket, Non-Marring Lug Nut Thin Wall Deep Socket Set
Just a quick video showing how to replace the rear brake pads on a 2011 Honda Pilot. I also show how to remove and replace the rotor/drum combo if you need to change your rotors as well. This is the Same as many other Honda Models.
Tools Needed:
Large Screwdriver or pry bar
12mm Socket and Ratchet or breaker bar
17 mm Socket and breaker bar or impact wrench
Torque Wrench
Brake Grease (Do not use Petroleum based grease)
Wire Brush or wheel (wear safety glasses)
Torque spec I found online for the small caliper slide pin bolts is 27 ft lbs
Torque spec I found online for the caliper bracket bolts is 65 ft lbs
Here's a video I made of the front brake pads & rotors on this same vehicle: • 2011 HONDA PILOT - HOW...
Thanks for Watching!
Please Subscribe!
-Dan the Fix it Man
www.amazon.com/shop/danthefixitman
Song used in the video:
'ILY Baby' by Dyalla
As an Amazon Associate I earn from qualifying purchases.
Пікірлер: 11
Excellent videos. You make it sooo simple! And explain it well without extra BS.
Great video well done !
awesome vid thx!!!
Thank you
I would never use thread lock on those bolts...they are usually a bitch to get off and I've never come across a loose one.
Thanks for the video !.!. Can you use the caliper grease on the front pins as well or would this be only for the rear caliper pins ?.
@DantheFixitMan
Жыл бұрын
It’s ok to use it for the front pins and contact points too. Just be careful to not get any on the friction Surface of the pads or the rotor. Thanks for watching! -Dan the Fix it Man
I noticed you used this Versachem 26080 Synthetic Caliper Grease for this Rear Brake Pad replacement video. But you used a different grease for your Front Brake Pad replacement video. So do I need to buy both grease versions for front and rear calipers?
@DantheFixitMan
11 ай бұрын
No, either one will work fine for the front and back slide pins. The videos were a few years apart and I had changed the brand that I was using. Thanks for watching! -Dan the Fix it Man
So I don't need to open the Brake fluid Cap under the hood when I flush the pistons for front and rear brakes?
@DantheFixitMan
11 ай бұрын
No, I don't think it's necessary if you're just pushing the pistons back into the caliper. I don't open the cap unless I need to add or remove fluid, unless the master cylinder reservoir is very difficult to see through to determine the correct fluid level. Thanks for watching! -Dan the Fix it Man