It's crazy how much road salt can impact our cars. Nicely done, looks like quite a project!

@T-MillProductions

Жыл бұрын

Oh it was lol. Good ol Wisconsin salt. Can’t wait till spring comes!

@micky2567

Жыл бұрын

Salt is so hard on cars, I give you props for working on that rusty stuff all the time!

@molly4046

Жыл бұрын

Great video man! Really detailed , I appreciate it!

@T-MillProductions

Жыл бұрын

Thanks a lot!

Awesome job bud, thanks for sharing the knowledge! I'm heading back out to the garage with some new skills, thanks again!

@T-MillProductions

10 ай бұрын

Thank you very much! I appreciate you watching and I appreciate the nice comments! I hope your project goes well and you get it done fast and easy. Have a great day!

0:10 Video to replace "a Wheel bearing" 2008 Ford Edge Why label video -- ball joint? 16:08 Well, watched this far. Satisfied ball joint replaced. Nice touch 15/16 socket.

@T-MillProductions

3 ай бұрын

lol so funny story, I was actually doing a ball joint, axle, and wheel bearing so I tried to make 3 videos out of it and I just cut parts out depending on the video

done that ,very well done

@T-MillProductions

4 ай бұрын

Thank you!

life saver

@T-MillProductions

3 ай бұрын

Thanks

Real life video 👍🏽👍🏽👍🏽

@T-MillProductions

Жыл бұрын

Thank you, I try to do the best I can

The ball joint once it is pressed in should not be loose. The snap ring is there to keep the ball joint from falling (in case it loosens up).

@T-MillProductions

7 ай бұрын

I agree!

Has anyone had the “ABS” light on their dashboard?

@T-MillProductions

9 күн бұрын

I have

I love you

@T-MillProductions

4 ай бұрын

Thank you

Question is how long did that ball joint last? Loose is not good and IMO prone to failure. Best repair is a new LCA. Other than that. Thanks for the video.

@T-MillProductions

Жыл бұрын

Hey man nice to see you watching my videos lol. I’ve been a long time subscriber of yours. So this control arm I did replace just a couple months prior to this video. There was a road by my house that was horrible for a long time and after enough drives on it this ball joint went bad. I do agree with you that if the control arm is original just replace it. Watch my other video on control arm tips and tricks.

@T-MillProductions

Жыл бұрын

In that video I show what to do if the front speed but weld breaks

Not sure if I missed this in the video, but when do you grease the ball joint? When the knuckle is seated? Does the ball joint you installed come with grease in it already? Ty in advance, working on my ford edge today!

@T-MillProductions

Жыл бұрын

So oddly enough 1 ball joint had a grease fitting and the other side didn’t for some reason. I personally grease them after they’re installed and the whole job is done, I jack it up so all the tension is off of the ball joint and then I grease it . If you try to grease it before you install it all the grease with shoot out when you run the big nut down. Hope this helps! Thanks for watching and if you needs any more help please don’t hesitate to ask!

If you can get a decently priced control arm with the ball joint You wont have to remove all that.

@T-MillProductions

3 ай бұрын

So i did the control arms multiple times in this thing and those junk non greasable ball joints don’t last for crap where I live so I change them out with greasable ones