www.williamsmobileclutch.co.uk 🇬🇧 Contact us for your clutch replacements. Thanks for the suggestions and continued support for us small businesses. Kind regards. K-A. Williams.

@stephansondkhar3964

2 жыл бұрын

I need help for ecco sport automatic transmission to replace clucth plate

@AT-AT3

4 ай бұрын

HI , how much time would you tell you spent to realise this operation ?

Massive thanks to Kevin for carrying out the clutch replacement on my Mondeo 👍 What a professional, I can't recommend him enough. Hopefully the rest of the car lasts as long as the new clutch. Many thanks.

@jasonwiggins7894

2 жыл бұрын

Yes he did a great job mate may I ask you how many miles your Mondeo has and also how long was the dmf rattling before you have the job done many thanks Jason

@andrewmount278

2 жыл бұрын

@@jasonwiggins7894 Hello mate, she's done 187250.miles. It started playing up early December, vibrations through the clutch pedal, it was ok when fully engaged and unengaged. But when it was partially engaged wow what a noise and vibration. I also had the clutch go all the way to the floor a few times, but it came back up if you put your foot under it. Hope that helps, I can't recommend Kevin enough though if you do get it changed.

@jasonwiggins7894

2 жыл бұрын

Wow that is great mileage no complaints there Andrew there's lots of Mondeo haters out there but I think they are a great car ready to do another 180000 then catch you later bud

@leebenstead7171

Жыл бұрын

Hi Andrew, did you need to have the wheel alignment checked due to the subframe being loosened? I have the same car/year as you and will being carrying out the same job. Thanks.

@andrewmount278

Жыл бұрын

@@leebenstead7171 Hi Lee No I didn't, the steering wheel was still centred well and she wasn't pulling either way. However I've just replaced the N/S lower arm ball joint and the steering wheel isn't central anymore and she's pulling to the left a little bit, so I will be getting the wheel alignment done now. Hope that helps.

You're a man among men. Thanks for sharing your work with the public.

I have not seen anyone on KZread film better than this. This guy has mastered the clutch change.

@WMCS

2 жыл бұрын

Thanks for the feedback 🍻

Hi mr WILLIAMS. I just want to thank you from France. I could change a clutch on my 2005 Ford mondeo 2.2 TDCI thanks to you. The 2005 Ford mondeo 2.2 TDCI and the 2007 2.0TDCI ZETECH videos were very helpfull. I take my time, and now it's done. The way you shoot your videos are so precious and detailed. So thanks a lot, you do a great job under a car, but an another one as much great to filming your job, cut it, and upload it on youtube. Un grand merci pour vos vidéos et votre partage! Kind regards

Did this exact job on the same model car a couple of years ago on my drive. Took me two days and a bath full of Radox afterwards. He makes this look easy when it is anything but. Man handling gearboxes like that takes some doing, and he clearly earns every pound he makes. 👏👏

@jasonwiggins7894

2 жыл бұрын

Lol... me same as you David I had to get assistance getting the box out and in I didn't fancy dropping it on my lap

Kudos to you Kevin.... You just don't know how to quit... Even if it's raining, snowing or hell will break loose, you just keep going untill the job is done... Stay cool.... "Cheers" From Guatemala I salute you....

Kewin, świetna robota. Podziwiam Cię za to że robisz to na ulicy bez podnośnika w tak krótkim czasie. Szacunek.

as always, very professional and making it look easy. fantastic job 👍🏻

Kevin,another masterclass in mechanical engineering and documentary filming making. Great!!!!

Восхищаюсь твоей работай , что ты делаешь на улице это просто не реально у нас в России город Санкт -Петербург такого даже в сервисах не могут проделать ) уважение тебе

Thats a ball ache of a job on a ramp let alone on the floor, much respect.

awesome camera work among other things

Might be cheaper to set fire 🔥 to it and claim the insurance money than to replace the clutch ! Great Job!

You sir, have the heart of a lion. I take my hat off to you.

@WMCS

Жыл бұрын

Thank you

I love watching your work mate thank you for all your efforts

@WMCS

2 жыл бұрын

Thanks for the feedback

Amazing video, I work for an ford dealer as mechanic in germany and i can tell, 13:46 this screw is such a pain with newer models even here its hard to reach.

@WMCS

2 жыл бұрын

Very true. A lot of time it seizes up. Because the thread is exposed on the opposite side that sits in a recess dam that holds water every time it rains.

@TheAnimus14

2 жыл бұрын

@@WMCS But I have to say I take some ideas from your way to work. You are a great guy and awesome mechanic.

This video makes the Mini videos look like a walk in the park! What a mission! You had to take half the car apart. You took it in your stride though and made it look easy….as usual :-)

Nice work as always remember doing one of these back in the day on my back regretted starting it 😂

Con este video se aprende a desmontar y armar muchas otras cosas además del clutch ,muchas gracias por compartir tu trabajo, que Dios te bendiga y tengas exitos en tu profesion.

Somebody need several days, what you are doiung in several hours. Very good video !

@WMCS

Жыл бұрын

Thank you.

Ford Mondeo is very hard to work. Fantastic vídeo as always Thumbs up one more time👍

Кевин, спасибо за твои ролики... Получилось самому, заменить сцепление с маховиком на vw T5... Удачи тебе!.. Привет из Архангельска!

Those mk3s getting rare this days. My fav Mondeo.

@WMCS

2 жыл бұрын

Definitely.. they are like tanks to be honest ..

@wellwh0

2 жыл бұрын

@@WMCS yup. My dad has it. 16 years strong. Only issue is bloody DMF. Replaced twice.

mammoth of a job with a huge gearbox, but still no probs for Kevin-Albert Williams. Thumbs up from me buddy 👍

@WMCS

2 жыл бұрын

Definitely was a tank this one 😁

Nicely Kelvin..same as me done in Malaysia 🇲🇾

@anisibrahim8931

2 жыл бұрын

Can you share more video to me..I’m interesting your skill fix the car

Great work on the Ford Mondeo TDCI

These videos are unreal. Your like spiderman under these cars. A pop up gazebo from aldi/lidl cheap and cheerful might keep u a bit dry on poxy days. Really enjoyed watching.

Mükembel işçilik ve ustalık saygılar takipdeyim👍😉

Hi Kevin fantastic video as always .all the best Shaun

@WMCS

2 жыл бұрын

Thank you Shaun 🍻

I wish we had such a Service in Germany too:-)

As us mechanics we all know what there like. Il give you Kevin you do have luck on your side, the amount of chassis legs iv had to cut open to well the nut back on lol. Fer play!

Very good job

That car just kept giving didn't, as far as what all had to come apart.... great, clean job as always.....

Nice job bro, Advice, start at the top fisrt while the car is on the ground. In that way, it is easier to reach because the car is not too high. Also, because you are alone, just put the wheels underneath the car just incase the jack stands falls or fails then the car will fall on top of the wheels. Cool😎

Enjoyed this Kevin. Nice one. Also - easier when you lift the box off and push the subframe back up when reassembling.... (I'm using a jack) 😂

Brilliant! Thank you.

Super job 👍👍

Grazieeee mille per il Video

this is fantastic

Hola Albert, mondeo complicado mucho para desarmar de ru parte impecable trabajo ..!!

Un máquina Kevin!!!

nice work))

Skills as ever kev! Would have been interesting to do a clutch on the Subaru or mx5 in the BG 👍🏻

@WMCS

2 жыл бұрын

I’ll definitely keep an eye out for MX5 .. I’ve done one before they’re not bad at all

Sehr gut

Great stuff. What weight do you reckon the gear box is? Back in the day our Mondeo's dmf was replaced with a solid one. Regards Charles

Buen trabajo, yo tengo que hacer otro igual jejej

Good work. Can you list the the equipment you use and your work chothes

HELLO KEVIN, GOOD JOB. WHAT MODEL OF IMPACT WRENCH DO YOU USE?

Is that rubber grease you're using on the input shaft and bellhousing bolt holes?

Hi ! I always watch your videos, I can say that you are the number 1, I have to make a Mercedes vito, and I have not seen any videos. Did you share any videos about it?

This video perfectly shows how big a pain in the arse mondeos are to work on.....one of the most frustrating, swear inducing vehicles ever designed. Great work as always by K-A W

Eyval bro, 👌

What were Ford thinking of when they built that car. Great video…

When the clutch sender is punctured and leak fluid, is it possible to change just him by up and change just the liquid ?

Just curious have you ever tried using a creeper ?. Getting on a bit myself (67) but my arms and neck ache for days after lying on back under car. Really enjoy watching your immense skills !!

Hello. How thick are the panels that you put under the machine while you work?

Just a quick question please, I have installed the new gearbox on fiesta mk6 1.25, just wanted to ask if you advise back bleeding the clutch fluid or do you have any advise on best/safest way, thanks 🙏 love your videos

@CookieScaley

2 жыл бұрын

I know you want a reply from the man himself but with bleeding the clutch you can do it either way you like. I usually only back bleed if I'm having trouble getting air out of the master cyclinder

You make this look easy my man ! One question : you didn't drain the gearbox before removing the cardan shafts ?

Mate i wana get the milwaukee electric ratchet im wondering what better the long reach one i do some you with or smaller one

Nice one. How much is to replace it? Need mine done and it’s the same engine. Cheers

Omg. That mondeo actually tired you alot. Alot of stuff needs to come out just for a clutch. Really good job kevin. Love you alot❤❤. And i want to ask a question. You now when you put the clutch on and then when you start putting the gearbox back on. When you start putting it on does the clutch inside the gearbox move when your putting it in so that the gear box sits. Like i mean when you try and put the gearbox back on. Does the clutch move by it self so that it sits even if youve titened the clutch bolts? please answer my question i really want to know❤❤❤❤

Helo from Poland. I hawe mk3 2.0 tddi. Thanks for movie. Good luck.

@Luton-Mick

2 жыл бұрын

I had a tddi, the best diesel Mondeo they made until they stuck that crap common rail junk with playdough injectors and self destructing high pressure fuel pumps.

It’s 21:00hrs I started renewing my gearbox on the fiesta mk6 1.25 at 08:00hrs, I’m exhausted, covered in bruises and marks, got gearbox oil all in my eyes and face, all I can say is you must have arms like pop eye, oh and I had help off a second person, the clutch pedal felt a bit spongy, so should I bleed it a bit more, I did it about ten times but I lost my will to live 😂

Hi, can you tell me what power/impact ratchet you use? struggling with bolts! great videos!!!

@brianmason8400

2 жыл бұрын

The big impact is an M18 fuel 1/2 drive, and the ratchet is the M12 fuel 3/8drive extended reach.....I believe on both. Kevin, my apologies if I interrupted.

👏

Where'd you get that tray from Kev? That black one you stick all your bits in.

@WMCS

2 жыл бұрын

I got it from my local garden centre

Hi there I did my clutch by watching your video thank you for that but I have a little problem sometimes now when I press clutch in coming to a junction the revs will drop and car will stall will start straight up if I turn key of and on again have you ever had this problem please

@WMCS

2 жыл бұрын

Sounds like the breather hose may be loose or have come disconnected

@robertbentley4217

2 жыл бұрын

Do you mean air box sorry for been a pain

I kind of wonder what you do when you see all the other things that need doing on these vehicles. Even a wash would be nice for some of them

@WMCS

2 жыл бұрын

I suppose you’re just gonna have to keep wondering with Alice .. Yes I can always wash the car .. Is that your fantasy 😉..

@andrewmount278

2 жыл бұрын

She'll get her yearly wash once I've done the pads and discs later in the summer 😁

Hello. Does the dual-mass clutch from the mondeo mk3 2.0 TDCi fit the mondeo mk3 2.2 TDCi?

@WMCS

2 жыл бұрын

I very much doubt as the crank will be of different thickness

Hi Kevin Question: I done the clutch in a Volvo V40 nine months ago and it’s slipping again due to a very elderly owner, would I get away with not changing the DMF ?? it has only done around four thousand miles roughly… I know you said before you change the DMF in every clutch repair or else you won’t take on the job But in this circumstances what would you do. Regards Eric

@WMCS

2 жыл бұрын

Eric in this circumstance which I’ve come across myself before .. within a year the csc had malfunctioned .. I would confidently leave any DMF Within 30k miles.. a DMF lifespan usually is between 60-80k miles for any recent cars ..

@castrolgtx5064

2 жыл бұрын

@@WMCS Thanks for the reply💥👍

@castrolgtx5064

2 жыл бұрын

@@okornel Thanks for the reply💥👍

Super Arbeit! Aber so wie der Wagen von unten aussieht, müsste der mal was gegen Rost tun.

You should get a big gazebo to work under, when it rains

what machine william you have to repair health william

@WMCS

2 жыл бұрын

Hola Miguel🍻

I feel exhausted after watching that.

Is this much differen drom the 2.0 petrol?

@WMCS

2 жыл бұрын

Yes … a lot more involved than the petrol ones. I think I’ll have one up on the channel soon.

@rimmersbryggeri

2 жыл бұрын

@@WMCS Thanks in advance. I have the Haynes manual fo the car but your videos are so much more instructive.

@mickm234

2 жыл бұрын

@@WMCS I shall look forward to it. My 2.0 litre Ghia needs doing. Why is a petrol one easier to do than the diesel please?

@vornamenachname4333

Жыл бұрын

​@@WMCS i have a MK3 2006 1.8 110HP - is it really much easier like this Diesel?

OMG what a ball ache to do kevin thats why I would never buy a ford now I done a clutch on my wifes sierra years ago 10pm at night but the new fords are a nightmare

headlight bulb replacment

@WMCS

Жыл бұрын

For sure.

🙋🏻‍♂️ how are you mate?

@WMCS

2 жыл бұрын

Holla holla 😁🍻✔️

@maverick507

2 жыл бұрын

😂

Ford's saying for Germany is - one leads away with Ford and never comes back 😁😁😁😄😄😄🤣😂

@WMCS

2 жыл бұрын

😆😂😂… oufff

Wow definitely not a DIY job anymore is it the same as a xtype

@WMCS

2 жыл бұрын

Yes exactly the same

@anthonythomas9456

2 жыл бұрын

@@WMCS I know my way around a engine bay but I think that's too bug of a job for me u sir got some serious skills what area u cover and how much would it cost for a xtype

Combien de kilomètres à cette auto merci

@andrewmount278

2 жыл бұрын

186000 miles, whatever that is in kilometres.

@patrickmalliart5736

2 жыл бұрын

Merci de votre réponse Cordialement Patrick.

Never again!

Niech ktoś mi w Polsce powie, że wymiana sprzęgła to cały dzień roboty...

@WMCS

4 ай бұрын

Subscribe to the channel for the weekly repair log. 🍻🍻🍻

What do you think about FORD ? For me they got the strangest contruktions all over! I cant stand FORD at all!!!!!!!!!!

@WMCS

2 жыл бұрын

Well the name itself gave birth to the automotive in all its aspect… so it’s come a long way from the model T..

@stefandiesel9218

2 жыл бұрын

@@WMCS here one strange example: the oilbath timing belt in the 1.0 eco boost engine! its just mad!!!

@brianmason8400

2 жыл бұрын

My opinion, ain't nothing wrong with Ford. ALL veh manufacturers have their goods and bads. Me personally, I'd take a Ford over about anything else, that's all my grandparents drove.

@davidkidd9007

2 жыл бұрын

I’ve had a lot of fords and for what you get they are value for money and pretty reliable . Imagine the cost of doing this on a German car through a garage .